Table of Contents
Advertisement
Parts and their functions
29.
M.GAIN/M.PED DISPLAY SELECT button <M.GAIN/
M.PED>
EXIT button <EXIT> (In setup mode)
Press this button to display and change M.GAIN or M.PED settings.
M.PED settings are only displayed, the DATA SET buttons <UP>
<DOWN> cannot be used to make settings. Use the Master pedestal
control <M.PED> to adjust the iris lever.
z Setting and Displaying M.GAIN/M.PED
1. Press <M.GAIN/M.PED> when IRIS or other (ND/CC,
SHUTTER) DISPLAY SELECT status is displayed.
The button lights and the M.GAIN display <M.GAIN> lights
green. (However, when M.GAIN is not at the standard position,
the display always lights yellow)
2. Press the lit DATA SET button <UP> <DOWN>.
This allows you to change the M.GAIN setting.
3. Press <M.GAIN/M.PED> again.
The M.GAIN display <M.GAIN> goes off and the M.PED display
<M.PED> lights green. (However, when M.PED is not at the
standard position, the display always lights yellow)
4. Press <M.GAIN/M.PED> again.
The button goes off and the M.PED display <M.PED> goes
off. (However, when M.GAIN or M.PED is not at the standard
position, the display stays yellow)
Then the setting display returns to IRIS indication.
<Note>
Use the master pedestal control to adjust M.PED. (This setting is
always available regardless of display status)
Pressing another Display Select button (<ND/CC> or
<SHUTTER>) turns off the button and lights the selected button.
To exit setup mode, hold down this button for about 2 seconds.
For details on setup mode, refer to Operations and Settings on the
supplied CD-ROM.
30.
M.GAIN display <M.GAIN>
The setting display lights green when a M.GAIN setting is displayed.
When the M.GAIN setting is not at the standard position, the setting
display always lights yellow regardless of what it shows.
(Standard position: 0)
When a M.GAIN setting is selected, the M.GAIN display lights.
31.
M.PED display <M.PED>
The setting display lights green when an M.PED setting is displayed.
When the M.PED setting is not at the standard position, the setting
display always lights yellow regardless of what it shows.
(Standard position: 0)
Operating the master pedestal control <M.PED> when the setting
display shows something other than M.PED will replace this indication
with the M.PED value for about 2 seconds.
<Note>
Use the master pedestal control <M.PED> to adjust M.PED. (This
setting is always available regardless of display status)
32.
SHUTTER DISPLAY SELECT button <SHUTTER>
EXECUTE button <EXECUTE> (In setup mode)
Press this button to display and change SHUTTER settings.
<Note>
When the Shutter On/Off button <SHUTTER ON> is set to Off, the
SHUTTER DISPLAY SELECT button <SHUTTER> is available and
the SHUTTER can be adjusted. (Adjustments can be made prior to
operation)
z Setting and displaying the SHUTTER
Hold down the STEP/SYNC select button <STEP/SYNC> for
about 2 seconds to switch between STEP and SYNC settings.
When SYNCRO is selected, the SYNCRO display lights green.
1. Press <SHUTTER> when IRIS or other (ND/CC, M.GAIN/M.
PED) DISPLAY SELECT status is displayed.
The button lights and the SHUTTER display <SHT> where
STEP/SYNC is selected lights green.
Then the setting display shows the SHUTTER setting of STEP
or SYNCHRO selected using the STEP/SYNC select button
<STEP/SYNC>.
2. Press the lit DATA SET button <UP> <DOWN>.
This allows you to change the SHUTTER setting.
(continued)
3. Press <SHUTTER> again.
The button goes off and the SHUTTER display <SHT> goes off.
Then the setting display returns to IRIS indication.
Pressing another Display Select button (<ND/CC> or
<M.GAIN/M.PED>) turns off the button and lights the selected
button.
In setup mode, it confirms menus and set values.
For details on setup mode, refer to Operations and Settings on the
supplied CD-ROM.
33.
SHUTTER display <SHT>
The setting display lights green when a SHUTTER setting is
displayed.
<Note>
Hold down the STEP/SYNC select button <STEP/SYNC> for about
2 seconds to switch between STEP and SYNC settings. When
SYNCRO is selected, the SYNCRO display <SYNC> lights green.
34.
SYNCRO display <SYNC>
The setting display lights green when a SHUTTER (SYNC) setting is
displayed. The STEP display light goes off.
Off:
SHUTTER is in STEP mode
On:
SHUTTER is in SYNCRO mode
<Note>
Hold down the STEP/SYNC select button <STEP/SYNC> for about 2
seconds to switch between the STEP and SYNCRO settings.
35.
Camera number tens' place digit display <10 to 19>
This LED lights when the camera number is a number between 10
and 19. Use setup mode to set camera number.
On:
The camera number is a number between 10 and 19.
Off:
The camera number is a number between 1 and 9.
36.
Camera number display <No.>
This function displays the camera number. Indicates the one's digit
of a camera number between 10 to 19. The ten's digit is indicated by
the ten's digit display.
Use setup mode to set the camera number.
37.
Camera select button <SELECT>
For future use.
15
Advertisement
Table of Contents
