Advertisement
Optional Steering Wheel Control Programming (cont.)
The Mute button can be set to control the factory OnStar functions or given the ability to control the aftermarket radio. This option
can be set using the program button on the side of the interface. The default setting for this button is factory mode which controls
the factory OnStar. If this button is set to aftermarket mode, OnStar must be accessed by using the factory controls located on
the rearview mirror.
Factory Mode
•
The SWC Mute button is programmed to control OnStar
It cannot be programmed for short press/long press dual
command functionality and is blocked from doing so.
Use the function chart on the next page as a guide to program the functions in the proper order for your new radio
1. Turn the key to the ignition position.
2. Press and release the programming button on the side of the interface the number of times that corresponds with either
factory or aftermarket mode. One press will set factory mode and two presses will set aftermarket mode. The LED will blink
each time the button is pressed.
3. Once you have chosen either factory or aftermarket mode, after 2.5 seconds the LED will come on solid. At this point you
have two options:
A. To restore the SWC to factory default settings: Simply wait 7 seconds and the LED will blink 3 times indicating
the interface has timed out. The default settings are now restored and no further action is required.
B. To program custom SWC assignments: Proceed to step 4
4. With the LED on, press the first button to be learned on the steering wheel, the LED will turn off. At this point you have
two options:
A. For short press functionality: Release the button within 1.5 seconds. The LED will turn back on.
B. For long press functionality: Hold the button until the LED starts blinking. Release the button and the LED
will go back to solid.
5. If you need to program more buttons, repeat step 3 for each additional audio function on the steering wheel.
6.
If you come across a function in the chart that your steering wheel does not have, or you do not want to program, press and
release the program button on the side of the interface to skip that function.
7. Once programming is completed, wait seven seconds. The LED will flash three times indicating end of programming.
8. Test the interface for proper functionality. Whenever a SWC is pressed the LED on the interface should blink. If any function
does not work, repeat the programming steps
Optional Programming Order
Alpine
1
Volume +
2
Volume -
3
Mute
4
Preset +
5
Preset -
6
Source
7
Track +
8
Track -
9
Power
10
Enter/Play
11
Band/Program
12
Receive
13
End
14
VR
15
Pacific Accessory Corporation
JVC
Kenwood
Volume +
Volume +
Volume -
Volume -
Mute
Mute
Source
Source
Track +
Play
Track -
Track +
Band/Disc +
Track -
Preset/Disc -
Disc/FM +
Select
Disc/AM -
Attenuation
Answer
Phone Receive
Voice Dial
Phone Reject
On Hook
Voice Dial
Off Hook
Mute (Multimedia
Power
units only)
Preset +
*Other = Advent, Boyo, Dual, Lightning Audio, Rockford Fosgate, & Visteon
Pacific Accessory Corporation
®
©2016 Pacific Accessory Corporation
www.pac-audio.com
Radio Replacement & Steering Wheel Control Interface
with OnStar Retention for General Motors Vehicles
Aftermarket Mode
•
OnStar control through the SWC Mute button is disabled.
This will free up the Mute button to send mute radio
command and another 2nd function.
Clarion
Other*
Volume +
Volume +
Volume -
Volume -
Mute
Mute
Source
Preset +
Search +
Preset -
Search -
Source
Band
Track +
Send/End
Track -
Send
Band
End
N/A
| Ph. 866-931-8021 | support@pac-audio.com
RP5-GM32
Pioneer
Sony
Volume +
Volume +
Volume -
Volume -
Mute
Mute
Preset +
Preset +
Preset -
Preset -
Source
Source
Track +
Track +
Track -
Track -
Band
Band
Reject Call/Source
Phone Menu
(Bluetooth equipped
radios only)
Answer Call
Answer/End Call
End Call
VR
Fusion
Volume +
Volume -
Mute
Source
Track +
Track -
Audio
Power
Rev. 022516
Page 3
Advertisement
