Yamaha PLG150-AP Owner's Manual page 62

MIDI Data Format
2.1.3.1 XG System On
11110000
01000011
0001nnnn
01001100
00000000
00000000
01111110
00000000
11110111
When ON is received, the SOUND MODULE MODE changes to XG.
Since approximately 50ms is required to process this message, be sure to
allow an appropriate interval before sending the next message.
2.1.3.2 XG System parameter change
This message sets the XG System block (see Tables <1-1> and <1-2>).
2.1.3.3 Multi Part parameter change
This message sets the XG Multi Part block (see Tables <1-1> and <1-3>).
2.1.3.4 Part Assign parameter change
This message sets the XG Part Assign block (see Tables <1-1> and <1-4>).
2.1.4 PLG150-AP Native parameter change
This message sets parameters unique to the PLG150-AP.
Each message sets a single parameter. The message format is as follows.
11110000
01000011
0001nnnn
01100111
0ggggggg
0mmmmmmm
0lllllll
0sssssss
:
11110111
For parameters whose Data Size is 2 or 4, the appropriate amount of data will
be transmitted as indicated by Size.
2.1.4.1 PLG150-AP Native System parameter change
This message sets the PLG150-AP Native System block (see Tables <2-1>
and <2-2>).
2.1.4.2 PLG150-AP Native Multi Part parameter change
This message sets the PLG150-AP Native Multi Part block (see Tables <2-1>
and <2-3>).
2.1.5 Other parameter change messages
2.1.5.1 Master Tuning
This message changes the pitch of all channels simultaneously.
11110000
01000011
0001nnnn
00100111
00110000
00000000
00000000
0000mmmm
0000llll
0xxxxxxx
11110111
In general, use the Master Tune parameter in XG System (see Table <1-2>)
26
PLG150-AP Owner's Manual / Bedienungsanleitung / Mode d'emploi
F0H Exclusive status
43H YAMAHA ID
1NH N:device Number
4CH Model ID
00H Address High
00H Address Mid
7EH Address Low
00H Data
F7H End of Exclusive
F0H Exclusive status
43H YAMAHA ID
1NH N:Device Number
67H Model ID
GGH Address High
MMH Address Mid
LLH Address Low
SSH Data
:
F7H End of Exclusive
F0H Exclusive status
43H YAMAHA ID
1NH N:Device Number
27H Model ID
30H Address High
00H Address Mid
00H Address Low
0MH Master Tune MSB
0LH Master Tune LSB
XXH don't care
F7H End of Exclusive
2.2 Bulk dump
This device uses only the following bulk dump messages.
[ XG BULK DUMP ]
1) XG System bulk dump
2) XG Multi Part bulk dump
[ PLG150-AP NATIVE BULK DUMP ]
1) PLG150-AP Native System bulk dump
2) PLG150-AP Native Multi Part bulk dump
2.2.1 XG bulk dump
This message sets XG-related parameters. Unlike parameter change mes-
sages, a single message can modify multiple parameters.
This message format is as follows.
F0H
11110000
01000011 43H
0NH
0000nnnn
4CH
01001100
SSH
0sssssss
TTH
0ttttttt
GGH
0ggggggg
MMH
0mmmmmmm
0lllllll LLH
VVH
0vvvvvvv
: :
KKH
0kkkkkkk
F7H
11110111
Address and Byte Count are given in tables <1-n>.
Byte Count is indicated by the total size of the Data in tables <1-n>.
Bulk dump is received when the beginning of the block is specified in
"Address."
"Block" indicates the unit of the data string that is indicated in tables <1-n>
as "Total Size."
Check sum is the value that produces a lower 7 bits of 0 when this Start
Address, Byte Count, Data, and the Check sum itself are added.
2.2.1.1 XG System bulk dump
This message sets the XG System block (see Tables <1-1> and <1-2>).
2.2.1.2 XG Multi Part bulk dump
This message sets the XG Multi Part block (see Tables <1-1> and <1-3>).
2.2.2 PLG150-AP Native Bulk Dump
This message sets the special parameters for PLG150-AP.
Unlike Parameter change, one message can modify multiple parameters.
This message format is as follows.
F0H
11110000
43H
01000011
0NH
0000nnnn
67H
01100111
0sssssss SSH
TTH
0ttttttt
0ggggggg GGH
MMH
0mmmmmmm
LLH
0lllllll
VVH
0vvvvvvv
: :
0kkkkkkk KKH
F7H
11110111
The detail are the same as for 2.2.1 XG Bulk Dump. However, see Tables <2-
n> for the Address, Byte, Count, and block.
2.2.2.1 PLG150-AP Native System bulk dump
This message sets the PLG150-AP Native System block (see Tables <2-1>
and <2-2>).
2.2.2.2 PLG150-AP Native Multi Part bulk dump
This message sets the PLG150-AP Native Multi Part block (see Tables <2-1>
and <2-3>).
3. Realtime Messages
3.1 Active Sensing
a) Send
This is not transmitted.
b) Receive
After FE is received one time, if the MIDI signal does not come within 300
msec, PLG150-AP will act the same as when ALL SOUND OFF, ALL
NOTE OFF, and RESET ALL CONTROLLERS are received, and return to
the condition where has not been received once.
Exclusive status
YAMAHA ID
N:Device Number
Model ID
Byte Count MSB
Byte Count LSB
Address High
Address Mid
Address Low
Data
Check-sum
End of Exclusive
Exclusive status
YAMAHA ID
N:Device Number
Model ID
Byte Count MSB
Byte Count LSB
Address High
Address Mid
Address Low
Data
Check-sum
End of Exclusive