Table of Contents
Advertisement
2
5
7
8
1. INPUT (Input mode selection)
The menu is displayed. Press
mode, and press
* You can select the input terminal by pressing the input
switch of the monitor.
Input mode
PC1 DVI-D
*1
*2
PC2 HDMI
PC3 D-SUB
*3
PC4 RGB
AV1 DVI-D
*1
AV2 HDMI
*2
AV3 COMPONENT
*3
AV4 S-VIDEO
AV5 VIDEO
*1 Select the terminal for DVI SELECT. (See page 7.)
*2 Select the terminal for HDMI SELECT. (See page 7.)
Select the terminal for HDMI AUDIO SELECT which is
used for audio input. (See page 7.)
*3 Select the terminal for BNC SELECT. (See page 7.)
2. MUTE
Turns off the volume temporarily.
Press the MUTE button again to turn the sound back to the
previous level.
3. MENU
Displays and turns off the menu screen (see page 5).
4. VOL +/- (Volume adjustment)
Pressing
or
menu screen is not displayed.
V O L U M E
Press
or
to adjust the volume of the sound.
* If you do not press any buttons for about 4 seconds, the
VOLUME menu automatically disappears.
Downloaded From TV-Manual.com Manuals
Basic Operation
1
3
4
6
or
to select the input
to enter.
Video
PC1 input terminal
PC2 input terminal
PC audio input
terminal
PC3 input terminal
PC4 input terminals
AV1 input terminal
AV2 input terminal
AV audio input
AV3 input terminals
terminals
AV4 input terminal
AV5 input terminal
displays the VOLUME menu when the
15
5. BRIGHT +/- (Backlight adjustment)
Pressing
menu screen is not displayed.
B R I G H T
Press
or
* If you do not press any buttons for about 4 seconds, the
BRIGHT menu automatically disappears.
6. SIZE (Screen size selection)
The menu is displayed.
Press
or
7. DISPLAY
Displays monitor information. Every time you press this button,
the display changes from INFORMATION 1 →
INFORMATION 2 → display clear and so on.
INFORMATION 1
Audio
LAN
1 9 2 0 x 1 0 8 0
INFORMATION 2
LAN
1 9 2 0 x 1 0 8 0
• The display disappears automatically after about 15
seconds.
•
is displayed during LAN communication.
LAN
• If
is displayed in red, there is a duplicate IP address.
LAN
8. MODE (Color mode selection)
Each time you press this button, the color mode changes in
the following order:
STD (Standard) → VIVID → sRGB → STD...
• sRGB applies to PC input only.
sRGB is international standard of color representation
specifi ed by IEC (International Electrotechnical
Commission). Color conversion is made in taking account
of liquid crystal's characteristics and represents color tone
close to its original image.
or
displays the BRIGHT menu when the
15
to adjust the brightness.
to select the screen size. (See page 4.)
XXXX/XX/XX XXX
INPUT MODE
:
PC3 D-SUB
SIZE
:
WIDE
COLOR MODE
:
STD
BRIGHT
:
15
VOLUME
:
15
ID No.
:
0
MODEL
:
LDT521V
S/N
:
STATUS
:
XXXX-XXXX-XXXX-XXXX
V: 60 Hz
H: 66.3 kHz
XXXX/XX/XX XXX
RS-232C/LAN SELECT
:
LAN
DHCP CLIENT
:
OFF
IP ADDRESS
:
XXX.XXX.XXX.XXX
SUBNET MASK
:
XXX.XXX.XXX.XXX
DEFAULT GATEWAY
:
XXX.XXX.XXX.XXX
MONITOR NAME
:
XXXXXXXXXXXX
DATA PORT
:
XXXXX
MAC ADDRESS
:
XX-XX-XX-XX-XX-XX
V: 60 Hz
H: 66.3 kHz
XX:XX:XX
XX:XX:XX
3
E
Advertisement
Table of Contents
