DeWalt DCF899HP2 Manual
Hide thumbs
Also See for DCF899HP2:
- Instruction manual (41 pages) ,
- Original instructions manual (141 pages)
Table of Contents
Advertisement
Quick Links
Definitions: Safety Alert Symbols and Words
This instruction manual uses the following safety alert symbols and words to alert you to hazardous situations and your risk
of personal injury or property damage.
DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
(Used without word) Indicates a safety related message.
NOTICE: Indicates a practice not related to personal injury which, if not avoided, may result in property damage.
Fig. A
Trigger switch
1
Forward/reverse control button
2
Anvil
3
Main handle
4
Battery release button
5
Battery pack
6
Worklight
7
Detent pin (DCF899)
8
Hog ring (DCF897, DCF899H)
9
7/16" (11 mm) Hex quick-release chuck (DCF898)
10
Speed selector
11
DCF897
3
1
11
7
5
6
WARNING: Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
WARNING: To reduce the risk of injury, read the
instruction manual.
if you have any questions or comments about this or
any D
WALT tool, call us toll free at:
e
1-800-4-D
WALT (1-800-433-9258).
e
English
2
4
1
Advertisement
Table of Contents
Related Manuals for DeWalt DCF899HP2
Summary of Contents for DeWalt DCF899HP2
- Page 1 English Definitions: Safety Alert Symbols and Words This instruction manual uses the following safety alert symbols and words to alert you to hazardous situations and your risk of personal injury or property damage. DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
-
Page 2: General Power Tool Safety Warnings
English GENERAL POWER TOOL SAFETY WARNINGS b ) Use personal protective equipment. Always wear eye protection. Protective equipment such as dust WARNING! Read all safety warnings and all mask, non-skid safety shoes, hard hat, or hearing instructions. Failure to follow the warnings and protection used for appropriate conditions will reduce instructions may result in electric shock, fire and/or personal injuries. -
Page 3: Additional Specific Safety Rules
English Additional Safety Information g ) Use the power tool, accessories and tool bits, etc. in accordance with these instructions, taking WARNING: ALWAYS use safety glasses. Everyday into account the working conditions and the eyeglasses are NOT safety glasses. Also use face or work to be performed. -
Page 4: Batteries And Chargers
English minimum wire size. The following table shows the correct • Do not charge or use the battery pack in explosive size to use depending on cord length and nameplate atmospheres, such as in the presence of flammable ampere rating. If in doubt, use the next heavier gauge. The liquids, gases or dust. - Page 5 When the FLEXVOLT™ battery is in a 60V Max* or a please call 1-800-4-D WALT (1-800-433-9258) or visit our 120V Max* (two 60V Max* batteries) product, it will operate website www.dewalt.com. as a 60V Max* battery. The RBRC® Seal shipping Mode: When the cap is attached to the The RBRC®...
-
Page 6: Charger Operation
English • Make sure that the cord is located so that it will not use it on any other voltage. This does not apply to the be stepped on, tripped over or otherwise subjected vehicular charger. to damage or stress. WARNING: Shock hazard. Do not allow any liquid to •... -
Page 7: Electronic Protection System
English screw exposed. Align the slots on the back of the charger DCB107, DCB112, DCB113, DCB115, DCB118, DCB132 with the exposed screws and fully engage them in the slots. Charging Charger Cleaning Instructions Fully Charged WARNING: Shock hazard. Disconnect the charger from the AC outlet before cleaning. -
Page 8: Future Use
English nOTE: Battery packs should not be stored completely Fig. D depleted of charge. The battery pack will need to be recharged before use. SAVE THESE INSTRUCTIONS FOR FUTURE USE Motor Be sure your power supply agrees with the nameplate marking. - Page 9 English Anvil with Hog Ring (Fig. G, H) The center position of the control button locks the tool in the off position. When changing the position of the control DCF897, DCF899H button, be sure the trigger is released. To install an accessory on the hog ring anvil, firmly push nOTE: The first time the tool is run after changing the accessory onto the anvil 3 ...
-
Page 10: Maintenance
D WALT Industrial Tool Co., 701 East Joppa Road, Towson, MD 21286, call 1-800-4-D WALT (1-800-433-9258) or visit our website: www.dewalt.com. Repairs The charger and battery pack are not serviceable. WARNING: To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment... -
Page 11: Register Online
WALT will maintain the tool and replace worn parts caused by normal use, for free, any time during the first year after purchase. 2 YEARs FREE sERViCE On DEWAlT BATTERY PACKs DC9071, DC9091, DC9096, DC9182, DC9280, DC9360, DCB120, DCB127, DCB201, DCB203BT, DCB207, DCB361...