Related Manuals for Jet JAT-124
Summary of Contents for Jet JAT-124
- Page 1 1/2” Right Angle Impact Wrench #505124, JAT-124 Operation & Parts Manual M-505124 Edition 1 02/2015 427 New Sanford Road LaVergne, TN 37086 Ph.: 800-274-6848 www.jettools.com Copyright © 2015 JET...
-
Page 2: Warranty And Service
Accessories; Shop Tools; Warehouse & Dock products; Hand Tools NOTE: JET is a division of JPW Industries, Inc. References in this document to JET also apply to JPW Industries, Inc., or any of its successors in interest to the JET brand. -
Page 3: Safety Warnings
10. The air tool must be properly lubricated before operating. Do not use this tool for other than its intended use. If used for other purposes, JET disclaims 11. Never start a percussion type air tool (chipper, any real or implied warranty and holds itself breaker, buster, etc.) without securing the... - Page 4 22. Shut off air supply and discharge any residual 33. Do not lubricate the tool with combustible pressure from tool before removing hose, liquids, such as kerosene, diesel or jet fuel. making adjustments, changing accessories, 34. Do not dispose of this tool with normal or storing tool.
-
Page 5: About This Manual
As with any tool operation, safety of operator and bystanders should be first priority. If there are questions or comments, please contact your local supplier or JET. JET can also be reached at our web site: www.jettools.com. -
Page 6: Tool Specifications
Specifications were current at time of publication, but because of our policy of continuous improvement, JET reserves the right to change specifications at any time and without prior notice, without incurring obligations. -
Page 7: Setup And Assembly
Any missing parts or damage should be reported Rotate air regulator dial to select forward or ® immediately to your JET distributor. Do not use a reverse (F/R) rotation. There are two speeds damaged tool. Read this instruction manual for forward, and one for reverse. -
Page 8: Maintenance
Tool Pressure Air system requirements JET Air Tools operate on 70-to-100 psi (pounds Use proper air hose size (refer to tool per square inch) air pressure measured at the tool specifications). The hose should be just long when the tool is operating. - Page 9 Use a light oil containing rust inhibitors, such as When using multiple hoses, air hoses should be SAE #10. Many JET air tools have integral oil larger than leader hose. Join multiple hoses reservoirs, which should be kept filled when in-line directly, rather than with quick connect fittings oilers are not used.
- Page 10 Troubleshooting JAT-124 Impact Wrench Any disassembly of the tool should be done by qualified service personnel. For problems not addressed below, contact JET technical service at 800-274-6846. Problem Possible cause Remedy Tool will not start. Air valve closed or obstructed.
-
Page 11: Replacement Parts
Problem Possible cause Remedy Severe air leakage. Air valve obstructed or damaged. Clean or replace. (Note: Minimal escape of Housing loose or damaged. Tighten or replace as needed. air is often normal for air tools.) Replacement parts Service parts are listed on the following pages. To order parts or reach our service department, call 1-800- 274-6848 Monday through Friday, 8:00 a.m. - Page 12 #505124, JAT-124, 1/2-inch Impact Wrench – exploded view JAT-124 Impact Wrench ...
- Page 13 #505124, JAT-124, 1/2-inch Impact Wrench – parts list Index Part No. Description Index Part No. Description JAT124-01 Hammer case JAT124-28 Rear end plate JAT124-02 Housing JAT124-29 Spring pin ø2.5x8 SK7 JAT124-03 Motor housing JAT124-30 Cylinder JAT124-04 Trigger JAT124-31 Rotor vane...
- Page 14 This page intentionally left blank. JAT-124 Impact Wrench ...
- Page 15 This page intentionally left blank. ...
- Page 16 427 New Sanford Road LaVergne, Tennessee 37086 Phone: 800-274-6848 www.jettools.com JAT-124 Impact Wrench ...