Subscribe to Our Youtube Channel
Related Manuals for Jet JAT-106
Summary of Contents for Jet JAT-106
- Page 1 Pneumatic Impact Wrench #505106, JAT-106 #505107, JAT-107 JAT-107 shown Operation & Parts Manual M-505106 Edition 2 11/2018 427 New Sanford Road LaVergne, TN 37086 Ph.: 800-274-6848 www.jettools.com Copyright © 2016 JET...
-
Page 2: Warranty And Service
Accessories; Shop Tools; Warehouse & Dock products; Hand Tools: Air Tools NOTE: JET is a division of JPW Industries, Inc. References in this document to JET also apply to JPW Industries, Inc., or any of its successors in interest to the JET brand. -
Page 3: Safety Warnings
15. Excessive air pressure and too much free Do not use this tool for other than its intended rotation may decrease life of the tool and may use. If used for other purposes, JET disclaims cause a hazardous situation. any real or implied warranty and holds itself 16. - Page 4 arsenic and chromium from chemically 32. Do not lubricate the tool with combustible treated lumber liquids, such as kerosene, diesel or jet fuel. Your risk of exposure varies, depending on 33. Do not dispose of this tool with normal how often you do this type of work.
-
Page 5: About This Manual
As with any tool operation, safety of operator and bystanders should be first priority. If there are questions or comments, please contact your local supplier or JET. JET can also be reached at our web site: www.jettools.com. -
Page 6: Tool Specifications
Specifications were current at time of publication, but because of our policy of continuous improvement, JET reserves the right to change specifications at any time and without prior notice, without incurring obligations. -
Page 7: Setup And Assembly
Setup and Assembly until it clicks into position. Any missing parts or damage should be reported Rotate regulator switch to preferred setting. immediately to your JET ® distributor. Do not use a Regulator settings are for reference only and damaged tool. Read this instruction manual do not indicate specific power settings. -
Page 8: Maintenance
Tool Pressure mechanisms. Always oil the tool and disconnect air hose before storage. JET Air Tools operate on 70-to-100 psi (pounds per square inch) air pressure measured at the tool Air system requirements when the tool is operating. Set tool to 90 psi unless indicated otherwise. - Page 9 When its useful life has expired, please leave tool Use a light oil containing rust inhibitors, such as at a specialized facility. SAE #10. Many JET air tools have integral oil Figure 2 Recommended arrangement of air piping and air line system...
- Page 10 Troubleshooting JAT-106/107 Impact Wrenches Any disassembly of the tool should be done by qualified service personnel. For problems not addressed below, contact JET technical service at 800-274-6846. Problem Possible cause Remedy Tool will not start. Air valve closed or obstructed.
-
Page 11: Replacement Parts
Problem Possible cause Remedy Severe air leakage. Air valve obstructed or damaged. Clean or replace. (Note: Minimal escape of Housing loose or damaged. Tighten or replace as needed. air is often normal for air tools.) Replacement parts Service parts are listed on the following pages. To order parts or reach our service department, call 1-800- 274-6848 Monday through Friday, 8:00 a.m. - Page 12 #505106, JAT-106, 3/8-inch Impact Wrench – exploded view JAT-106,107 Impact Wrenches...
- Page 13 #505106, JAT-106, 3/8-inch Impact Wrench – parts list Index Part No. Description Index Part No. Description JAT106-01 Motor housing JAT106-23 Spring 40312 Screw M8x8L SB-1/8 Steel ball 1/8in. JAT106-03 Air inlet JAT106-25 Anvil bushing JAT106-04 Trigger JAT106-28 Hammer case JAT106-07...
- Page 14 #505107, JAT-107, 1/2-inch Impact Wrench – exploded view JAT-106,107 Impact Wrenches...
- Page 15 #505107, JAT-107, 1/2-inch Impact Wrench – parts list Index Part No. Description Index Part No. Description JAT106-01 Motor housing JAT106-23 Spring 40312 Screw M8x8L SB-1/8 Steel ball 1/8in. JAT106-03 Air inlet JAT106-25 Anvil bushing JAT106-04 Trigger JAT106-28 Hammer case JAT106-07 Exhaust diffuser JAT104-12 O-Ring 50x1.5 mm...
- Page 16 427 New Sanford Road LaVergne, Tennessee 37086 Phone: 800-274-6848 www.jettools.com JAT-106,107 Impact Wrenches...
Need help?
Do you have a question about the JAT-106 and is the answer not in the manual?
Questions and answers