TABLE OF CONTENTS INTRODUCTION Special Features Parts Check List ... 3 FCC AND IC REGULATIONS ... 4 IMPORTANT SAFETY INSTRUCTIONS ... 7 REPLACING THE BATTERY PACK ... 9 GETTING STARTED ... 12 WALL MOUNTING ... 14 EXAMPLES OF THE HANDSET DISPLAY ... 16 BASE UNIT FUNCTION KEYS ...
Up to 24 name characters or 11 phone number digits can be displayed. With the VTech VT 1930c, the user can easily answer a call by pressing any key other than the OFF, MUTE or VOLUME Keys.
¥ Detachable power supply. ¥ Non-volatile storage of security code, Caller ID and memory dial records. This manual is designed to make you familiar with the VTech VT 1930c. We strongly recommend you read the manual before using your phone.
5. Belt clip 6. Battery pack 7. Telephone line cord HANDSET AC POWER ADAPTOR TELEPHONE LINE CORD To purchase replacement battery packs, call VTECH Communications at 1-800-595-9511. In Canada, call VTECH Electronics 7377. VT 1930c SPARE BATT CHARGING HS IN-USE POWER Q.MEM...
Should you experience trouble with this telephone equipment, please contact: VTECH COMMUNICATIONS SERVICE DEPT. at 1-800-595-9511. In Canada, call VTECH Electronics at 1-800-267-7377. For repair/warranty information. The telephone company may ask you to disconnect this equipment from the line network until the problem has been corrected.
Page 7
FCC. For repair procedures, follow the instructions outlined under the VTECH Limited Warranty. This equipment may not be used on coin service provided by the phone company or Party Lines.
Page 8
Your VTech VT 1930c is designed to operate at the maximum power al- lowed by the FCC and IC. This means your handset and base unit can communicate only over a certain...
Never spill liquid of any kind on the product. 10.To reduce the risk of electric shock, do not disassemble this product, but take it to a VTech authorized service facility. Opening or removing cabinet parts other than specified access doors may...
There may be a remote risk of electric shock from lighting. 14.Do not use the telephone to report a gas leak in the vicinity of the leak. VTECH COMMUNICATIONS SERVICE DEPT. at 1-800-595-9511. In Canada, call VTECH Electronics at 1-800-267-7377.
REPLACING THE BATTERY PACK Charging The Handset Battery Pack The handset of your VTech VT 1930c cordless telephone is powered by a rechargeable battery pack. It charges automatically whenever the handset is in the base. You should charge the battery pack for 16 hours when you first receive your phone.
Page 12
REPLACING THE BATTERY PACK To Replace The Handset Battery Pack Follow The Steps Below: 1. Remove the battery case cover by pressing on the ridged lines and sliding downward. PRESS and SLIDE DOWNWARD 2. Discard the old battery pack. DonÕt put the old battery pack in a trash compactor or a fire - it could burst.
Page 13
In Canada, call VTECH Electronics at 1-800-267- 7377. Spare Battery Charger The VT 1930c has a built-in spare Battery Charger, which is located in the cradle of the Base Unit. NOTE: In order to benefit from this feature, you must obtain an optional Spare Battery...
GETTING STARTED Setting Up Your VTech VT 1930 c Choose an area near an electrical outlet and a telephone wall jack. AC Power Adapter Plug the AC power adapter into an electrical outlet and the DC connecter to the back of the base unit.
Page 15
3. Never touch uninsulated telephone wires or terminals unless the telephone line disconnected at the network interface. 4. Use caution when installing or modifying telephone lines. VT 1930c POWER HOLD INT.COM DIGITAL CORDLESS been...
WALL MOUNTING The Wall Mounting bracket is de- signed to fit on standard Wall Mounting plates. 1. Choose a spot near an electrical outlet and a telephone jack. Your phone requires a modular telephone jack and a standard electrical outlet (120v AC). The power cord is six feet long;...
Page 17
EXAMPLES OF THE HANDSET DISPLAY Handset Display Messages PHONE ON is displayed when the phone is in use. After pressing a volume key, this displays the current volume setting. This display warns of a low battery condition. The handset operates for at least 5 minutes after the low battery indication first appears.
THE LCD DISPLAY-EXAMPLES This display is confirms that a commu- nication link has been established with the Base. This message is displayed while in OFF mode, if another phone is currently using the same line. This message is displayed when both the handset and base unit are on a call together.
HOLD or SPEAKER PHONE to return to the call. With a Speakerphone call on HOLD, picking up an extension phone, or activating the VT 1930c Handset will turn the Speakerphone OFF. FLASH Key During a Speakerphone call, press this key to flash the line.
THE BASE UNIT LAYOUT HOLD INT.COM PULSE AC POWER JACK TONE PHONE CORD JACK RINGER TONE/PULSE SWITCH BASE RINGER ON/OFF SWITCH Q.MEM REDIAL FLASH MUTE SP.PHONE 9V DC TEL. LINE ANTENNA MEMORY DIALING CARD POWER INDICATOR HS IN-USE INDICATOR CHARGING INDICATOR SPARE BATT INDICATOR MEM KEY Q.MEM KEY...
BASE UNIT FEATURES Power Indicator Glows when the power supply is plugged in and power is applied to the Base Unit. HS In Use Indicator Glows when the Handset has been activated. Charging Indicator Glows when the Handset is placed in the Base Unit cradle.
QUICK REFERENCE GUIDE Set-Up Adapter ¥ Plug AC adapter into a standard electrical outlet and Base Unit. ¥ Set TONE/PULSE switch to PULSE or TONE. The unit is factory set to TONE. ¥ Let the handset battery pack charge for 16 hours before first use. ¥...
Page 24
QUICK REFERENCE GUIDE ¥ Press and hold MEM/PROG . The handset will display PROGRAM LOCATION. ¥ Enter a two digit memory location (00..20). The unit will store the number, emit a warbled tone to confirm successful programming and exit program mode. Memory Dialing (speed Dialing): MEMORY DIALING FLASH...
Page 25
QUICK REFERENCE GUIDE Using REDIAL From the Handset: ¥ Press the PHONE key, then REDIAL to automatically redial the last number you dialed. ¥ Press REDIAL so that the number is shown on the display and then press the PHONE key. From the Base Unit : ¥...
The earpiece volume level indicator on the display will change accordingly. There are four volume levels. FLASH You can use your VTech VT 1930c cordless phone with services such as Call Waiting. Simply press the PHONE key to FLASH the line.
Page 27
BASIC OPERATION With a Handset call an hold, picking up an extension phone, or activating the VT 1930c Speakerphone will turn the Handset OFF. With a Speakerphone call on hold, picking up an extension phone, or activating the VT 1930c Handset will turn the Speakerphone OFF.
PRESS PHONE INT.COM MUTE CLR/DEL Message Waiting Your VT 1930c is capable of detecting a Visual Message Waiting Indication, generated by many phone service providers. If you subscribe to Voicemail service from your local telephone company, and Visual Message Wait-...
ADVANCED FUNCTIONS The MSG. WAITING alert may reap- pear, as long as unplayed messages remain in your Voicemail box. NOTE: Message Waiting works in conjunction with Voicemail service from many local phone companies. This is an optional service. You are not required to subscribe to it.
Page 30
ADVANCED FUNCTIONS To select a different ringer type for the Base Unit do the following: Press and hold : MEM/PGM The display will show the following : Press : The display will show the following: Press : The display will show the following: Press : 1 for ringer type 1 2 for ringer type 2...
MEMORY DIALING Storing Memory (Speed) Dial numbers To program a speed dial location, do the following: ¥ With the Handset OFF, enter the telephone number you wish to store (20 Digits Maximum). ¥ Enter program mode by pressing and holding MEM/PGM .
MEMORY DIALING ¥ Press MEM/PGM again to exit memory dial mode and leave the number on the display. ¥ Press PHONE . The number on the display will be dialed after a 2 second pause. ¥ Note that if digits were on the display prior to entering memory dial mode, the contents of the speed dial memory will be...
CALLER ID (CID) Caller ID (CID) Your VTech VT 1930c cordless phone is capable of displaying the name and/ or phone number of the person calling, before you answer the phone. Subscription to Caller ID service through your local phone company is required to utilize this feature.
7 digits of the received telephone number will be used. Consequently, you would actually dial this: The VTech VT 1930c was designed to accommodate this situation. If you need to temporarily add a long dlstance prefix and /or area code (such as 1503)
CALLER ID (CID) Reviewing Numbers Calls stored in memory can be reviewed by pressing CID . The display will show the number of the most recent (Call #01). The top line of the display is used to indicate the memory location number and the bottom line of the display shows the name, see below: There may be additional characters...
CALLER ID (CID) Deleting Numbers Pressing the CLR/DEL button deletes the Caller ID (CID) number displayed. ¥ While the phone is in Caller ID (CID) mode, press the CLR/DEL key once to delete the current call and the display will show: ¥...
MAINTENANCE Taking Care Of Your Telephone Your VTech VT 1930c cordless telephone contains sophisticated electronic parts, so it must be treated with care. Avoid rough treatment Place the handset down gently. Save the original packing materials to protect your telephone if you ever need to ship it.
If you still have difficulty after trying suggestions, call Communications at 1-800-595-9511. In Canada, call VTECH Electronics at 1-800-267-7377. THE PHONE DOESNÕT WORK AT ALL. ¥ Make sure the Power Cord is pugged in. ¥ Make sure the telephone line cord is plugged firmly into the base unit and the telephone wall jack.
Page 41
IN CASE OF DIFFICULTY COMMON CURE FOR ELECTRONIC EQUIPMENT Electronics, like people, can sometimes get confused. If the unit does not seem to be responding normally, then try putting the handset in the cradle. If it does not seem to respond after trying this a few times, do the following (in the order listed): 1.
8770 SW NIMBUS AVENUE BEAVERTON, OREGON 97008 in Canada, ship the unit via UPS Insured, or equivalent to: Suite 200- 7671 Alderbridge Way VTECH Communications assumes no responsibility for units sent without prior Return Authorizatlon WHAT DOES OUR WARRANTY NOT COVER? ¥ Batteries ¥...
TECHNICAL SPECIFICATIONS FREQUENCY CONTROL Crystal Controlled Dual Synthesizer TRANSMIT FREQUENCY Handset : 925.05 MHz to 927.75 MHz ( All ten channels within this range) Base : 902.3 MHz to 905.0 MHz (All ten channels within this range) RECEIVE FREQUENCY Handset : 902.3 MHz to 905.0 MHz ( All ten channels within this range) Base...
Page 44
THE VTECH GROUP OF COMPANIES. Distributed in the U.S.A. by VTECH Communications, 8770 SW Nimbus Avenue / Beaverton, Oregon, 97008. Distributed in Canada by VTECH Electronics Canada Ltd., Suite 200 - 7671 Alderbridge Way Richmond, B.C. V6X 1Z9. Copyright 1998 for VTECH COMMUNICATIONS LTD..
Need help?
Do you have a question about the 1930c and is the answer not in the manual?
Questions and answers