® NERGY Disclaimer: ViewSonic Corporation shall not be liable for technical or editorial errors or omissions contained herein; nor for incidental or consequential damages resulting from furnishing this material, or the performance or use this product.
Getting Started Congratulations on purchasing a ViewSonic PJ700 LCD projector! Save the original box and all packing material for future shipping needs. Package Contents • ViewSonic PJ700 LCD Projector • AC power cords (US, Europe, China) • ViewSonic Wizard CD-ROM (includes User Guide in PDF format) •...
• Do not look directly into the lighted lens; doing so will cause severe eye injury. • Keep small children away from the projector. Children can be severely burned by the hot lens. Also, children are more likely to look directly into the lens. ViewSonic PJ700...
The power LED lights a steady green after warm-up. The steady green light indicates that the • ViewSonic PJ700 is ready to use. To turn off the lamp, press (and hold for 2 seconds) the Standby/On button. The power LED •...
Connecting Input and Output Devices Use Figure 3 below as a guide when connecting input and output devices to the ViewSonic PJ700 projector. Remote control sensor S-Video Video IN Audio IN L Audio IN R Audio IN 1 Audio IN 2...
To adjust the size of the projected area, refer to the following table. The table shows minim maximum distances from the screen that you can place the projector to achieve a specific sc All distances are given in inches. ViewSonic PJ700 Figure 4: Recommended Projector Distances Table 1: Recommended Distances to Screen...
Rotate the rear foot adjuster to align the image. The rear foot adjusts the horizontal alignment of the projected image. • Front foot adjuster Press the release button to lower the front foot adjuster Figure 5: Angle Adjustment Rotate the rear foot adjuster ViewSonic PJ700...
2, Video, or S-Video. On the remote control: Press the RGB button to select a computer (RGB) as the input source. Press the Video button to toggle between Video and S-Video. ViewSonic PJ700 Projector control pad LED indicators MUTE RESET...
Press the TIMER button on the remote control to activate the on-screen timer. Press the button again to turn off the display. Auto Button Press the Auto button on the remote control to automatically adjust the vertical position and horizontal position, phase, and size. ViewSonic PJ700...
Color Balance B darkens or lightens the Blue color of the projected image. Aspect selects an aspect ratio for the projected image. The aspect ratio is the ratio of width to height of the projected image. ViewSonic PJ700 SETUP Main Menu Video INPUT IMAGE OPT.
• Select V: Invert for a front projection ceiling mount. • Select H&V: Invert for a rear projection ceiling mount. Start up selects a start-up screen. You can select or deselect the ViewSonic Welcome screen to display automatically at start-up.
Sync on G (Synchronize on G) allows you to toggle On or Off the Sync on G option. If you are unsure whether you are using a Sync on G input device, leave this option set to Off. ViewSonic PJ700 OPTIONS Menu...
• Select V: Invert for a front projection ceiling mount. • Select H&V: Invert for a rear projection ceiling mount. Start up selects a start-up screen. You can select or deselect the ViewSonic Welcome screen to display automatically at start-up.
Power Operating conditions Storage conditions Dimensions and weight Regulations May require a Macintosh adapter ViewSonic PJ700 Type Three 0.9” 800 x 600 polysilicon, active matrix TFT LCD Pixels 480,000 (800 dots x 600 lines x 3 colors) Colors 16.7 million Type Manual zoom (1.2x), manual focus...
• A minor power surge can cause the lamp to shut off. Turn off the Power switch. Let the projector cool down, then restart. • The projector may have overheated. Allow the projector to cool down, then restart. • Recheck the power cord connection. • Replace the lamp module. ViewSonic PJ700 display menu to reset factory defaults. ®...
Page 20
• Adjust the audio source device. No video • Check the video input connections. • Adjust the Brightness. A bright dot appears in the picture • This is a characteristic of liquid crystal technology and is usually not a problem. ViewSonic PJ700...
Power Indicator Lights If the Lamp or Temperature indicator is red or flashing red when the ViewSonic PJ700 is turned on, there is a problem and you should not proceed. Turn off the projector and let it cool down. Power...
The lamp shuts off very soon because the remaining usage hours has elapsed. Replace the lamp immediately. The ViewSonic PJ700 is not receiving a signal from the source. The current horizontal or vertical frequency signal from the computer cannot be used by this projector.
Projector Lamp Figure 7: Lamp Replacement ViewSonic PJ700 Lamp Unit • To order a new lamp unit contact ViewSonic Customer Support. • Estimated lamp life is 1500 hours. Make sure the power cord is disconnected and the unit WARNING: is cool. Wait 45 minutes for the lamp to cool down.
Make sure the projector is cool and the power cord is unplugged before beginning. Vacuum the air-filter. Caution: Never operate the projector without the air-filter; doing so will damage the projector. “+” side Pull out Battery Holder Figure 8: Installing the Batteries ViewSonic PJ700...
Attaching the Optional Handle The ViewSonic PJ700 comes with an attachable handle. Follow the steps below to attach the handle. Handle hooks Figure 9: Attaching the Handle ViewSonic PJ700 The handle hooks are on the left side of the projector, as shown in the figure to the left.
How long the warranty is effective: ViewSonic projectors are warranted for two (2) years for all parts excluding the lamp, two (2) years for all labor, and ninety (90) days for the lamp from the date of the first consumer purchase.
If you have any questions concerning which proper power cord to use, please consult with the dealer from whom you have purchased the product. Switzerland ...SEV Britain...BASE/BS Japan ...Electric Appliance Control Act Figure A1 Figure A2 Maximum Current Rating of Unit 10 Amps 12 Amps 12 Amps 10 Amps 12 Amps ViewSonic PJ700...
CE Conformity The device complies with the requirements of the EEC directive 89/336/EEC as amended by 92/ 31/EEC and 93/68/EEC Art.5 with regard to “Electromagnetic compatibility,” and 73/23/EEC as amended by 93/68/EEC Art.13 with regard to “Safety. ViewSonic PJ700...