Advertisement
Speed Settings:
Range from 1000rpm - 3000rpm
5.3.
To start the polisher press and hold in the safety lock button (fig.5.1) and squeeze the trigger. When releasing the trigger, the safety lock
button will engage, preventing the polisher from being inadvertently started.
WARNING! The high speed settings are intended for sanding. If used for polishing an excessive amount of surface material may be
‰
removed.
Note: As the rubber support disc is flexible, when sanding it should not be used head on, but at an angle of approximately 10 to 20
degrees.
Contact your Sealey stockist for details of compound heads and lambs wool bonnets.
6. MAINTENANCE
WARNING! Before attempting any maintenance ensure the unit is unplugged from the mains power supply.
‰
6.1.
Keep the machine clean and dry. DO NOT use abrasives or solvents to clean the unit. Ensure all external head screws are tight.
6.2.
Clean regularly by blowing a jet of compressed air through side vents to ensure motor ventilation is kept clear.
WARNING!‰Wear approved safety eye protection and, if necessary, respiratory protection.
‰
Note: The following maintenance must only be carried out by a suitably qualified person or an authorised Sealey service agent.
6.3.
Check carbon brushes by removing each side screw, fig.1. Check to see if the brushes are worn or cracked. If so, the brushes must
be replaced to avoid sparking and damage to the armature. Always change brushes as a pair. Use only genuine spare parts as these
are specifically designed for the machine. Failure to do so may be dangerous and will invalidate your warranty.
6.4.
After each 500 hours of use replace the gear head grease to prevent gear wear and possible drive failure.
This tool is subject to the vibration testing section of the Machinery Directive 2006/42/EC. When operated in accordance with these
instructions and tested in accordance with the standard below, results in the following vibration emission declared in accordance with
EN 12096:1997
Model No: MS900PSEU Sander/ Polisher
Tested in Accordance with: BS EN ISO 28927-3:2009
Measured Vibration Emission Value (a): 7.678m/s²
Uncertainty value (k): 1.5m/s²
These values are suitable for comparison with the vibration emission levels of other tools that have been obtained using the
same test method.
This tool may cause hand-arm vibration syndrome if its use is not adequately managed.
A health and safety assessment by the user (or employer) will need to be carried out to determine the suitable duration of use for each
tool. Note that the value declared is an average figure from a series of tests according to the applicable standard. The value may differ
depending on a number of variables including but not limited to; the user; the condition of the tool; attachments made to the tool i.e.
sockets, grinding/cutting discs, sanding discs, blades, handlesand leader hoses.
Health surveillance.
We recommend a programme of health surveillance to detect early symptoms of vibration injury so that management procedures can
be modified to help prevent significant handicap.
Personal protective equipment.
We are not aware of any personal protective equipment (PPE) that provides protection against vibration injury by attenuating the
vibration emissions of this tool. We recommend a sufficient supply of clothing (including gloves) to enable the operator to remain warm
and dry and maintain good blood circulation in fingers etc.
Guidance relating to the management of hand arm vibration can be found on the HSC website www.hse.gov.uk – Hand-Arm Vibration
at Work.
.
WEEE REGULATIONS
Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic Equipment
(WEEE). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid
waste authority for recycling information.
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500
© Jack Sealey Limited
WARNING! - Risk of Hand Arm Vibration Injury.
01284 703534
sales@sealey.co.uk
Original Language Version
www.sealey.co.uk
MS900PSEU | Issue:2 (H,F) 29/08/19
Advertisement
