Advertisement
Secure non-stable work piece with a clamp, vice or other adequate holding device.
9
Remove adjusting keys and wrenches from the machine and its vicinity before turning it on.
9
DO NOT use equipment for any purpose other than that for which it is designed.
8
DO NOT operate the polisher/sander if any parts are damaged or missing as this may cause failure or possible personal injury.
8
WARNING! DO NOT sand any materials containing asbestos.
‰
DO NOT switch the polisher/sander on whilst the head is in contact with the work piece and avoid unintentional starting.
8
DO NOT get the polisher/sander wet or use in damp or wet locations or areas where there is condensation.
8
DO NOT allow untrained persons to operate the polisher/sander.
8
DO NOT operate the polisher/sander when you are tired, under the influence of alcohol, drugs or intoxicating medication.
8
DO NOT use the polisher/sander where there are flammable liquids, solids or gases such as paint solvents, etc.
8
DO NOT leave the polisher/sander operating unattended.
8
DO NOT carry the polisher/sander with your finger on the power switch.
8
DO NOT pull the cord to remove the plug from the power supply.
8
Use a qualified person to lubricate and maintain the polisher/sander.
9
When not in use unplug from the mains power supply and store in a safe, dry, childproof area.
9
LEAD PAINT WARNING! Paint once contained lead as a traditional ingredient. Contact with the dust from the removal of such paint is
toxic and must therefore be avoided. The following action must be taken before using machine as a sander:
1. User must determine potential hazard relating to age of paint to be removed. (Modern paints do not have lead content).
2. DANGER! Keep all persons and pets away from the working area. The following are particularly vulnerable to the effects of lead
paint dust: Expectant women, babies and children.
3. We recommend personal protection by using the following safety items:
A) Paint Spray Respirator (Sealey ref. SSP1699) B) PE Coated Hooded Coverall (Sealey ref. SSP266). C) Latex Gloves (Sealey
ref. SSP24).
4. Take adequate measures to contain paint dust, flakes and scrapings. Wear safety equipment, as in (3) above and thoroughly clean
all areas when task is complete.
5. Ensure the paint waste is disposed of in sealed bags or containers according to local regulations.
2. INTRODUCTION
Features six speed power control suitable for sanding and polishing. Speeds range from 1400 to 3000rpm. Alloy bevel gear head with composite
motor housing. Supplied with Ø170mm backing pad and side handle. Fitted with Schuko Plug.
3. SPECIFICATION
Model no ........................................................... MS900PSEU
Free speed ...................................................... 1000-3000rpm
Motor power ................................................................1300W
Supply ................................................................. 230V - 5.8A
Pad size .................................................................. Ø170mm
Thread size ......................................................... M14 x 2mm
Noise power .................................................................92dBA
Noise pressure .............................................................81dBA
Vibration ................................................................. 7.678m/s²
Uncertainty ................................................................. 1.5m/s²
VIBRATION.................................................. 7.678
4. ASSEMBLY
WARNING! Ensure the unit is not plugged into the
‰
mains supply before attempting assembly.
4.1.
Attach the side handle.
Note: there is a mounting hole on either side and the
top to suit the application and/or operator.
4.1.1.
To attach the rubber pad, fig.2:
Thread the rubber pad on shaft (S) and tighten using
spanner by holding shaft steady with spindle lock.
4.1.2.
To fit a sanding disc, fig.2:
Select the grade of self adhesive
sanding disc required (D), peel off the backing and
centrally locate the disc onto the rubber pad.
To fit a polishing bonnet, fig.3:
4.1.3.
Fit the polishing bonnet (Z) over the secured rubber pad,
using the pull cord, tighten the bonnet and tie a bow to
secure, tuck the loose ends of the bow neatly under
the bonnet.
5. OPERATION
WARNING! Ensure you read, understand and apply the safety
‰
instructions in Section 1.
‰ WARNING! The warnings, cautions and instructions discussed in this manual cannot cover all possible conditions and situations
‰
‰
that may occur. It must be understood that common sense and caution are factors which cannot be built into this product, but
must be applied by the operator.
5.1.
Ensure the power control switch is NOT locked on before plugging into the mains.
5.2.
Hold the polisher firmly with one hand on the handle grip and the other on the side handle. To select the required speed rotate the
speed selector switch, fig.1, to the required speed 1 to 6.
© Jack Sealey Limited
A
fig.2
Original Language Version
fig.1
fig.3
MS900PSEU | Issue:2 (H,F) 29/08/19
Advertisement
