Related Manuals for LG UW34 Series
Summary of Contents for LG UW34 Series
- Page 1 INSTALLATION MANUAL LED TV* Please read this manual carefully before operating your set and retain it for future reference. UW76** UW34** www.lg.com...
-
Page 2: Table Of Contents
LANGUAGE & COUNTRY SELECTION - DIAL - Automatically for Setup - TV Name - Manually for Setup - SoftAP - USB LG Smart Install Utility TV MANAGER - USB Download Menu INSTALLATION MENU INTRODUCTION LG HOTEL MODE - Hotel Mode Operation... -
Page 3: Location And Function Of Controls
LOCATION AND FUNCTION OF CONTROLS LOCATION AND FUNCTION OF CONTROLS Parts and Button Screen Remote control and Intelligent sensors Power Indicator Intelligent sensor - Adjusts the image quality and brightness based on the surrounding environment. Joystick Button - This button is located below the TV screen. NOTE You can set the power indicator light to on or off by selecting General in the main menus. -
Page 4: Led Clock Connection
LOCATION AND FUNCTION OF CONTROLS LED Clock Connection (Depending on model) This TV can be connected to a LED Clock via the CLOCK port. CLOCK LED Clock (*Not Provided) -
Page 5: Ezmanager
EZMANAGER EZMANAGER • Image shown may differ from your TV. INTRODUCTION The Pro:Centric Platform enables you to simply install, manage and use guest-centric solutions. The default Domain “procentric.local” and IP Server Address are needed to be registered in DNS TV will contact the IP Server using the default Domain “procentric.local” via IP on server search page. If TV doesn’t contact the Server, TV will search the pre-defined channel earlier than all channels. -
Page 6: Language & Country Selection
EZMANAGER LANGUAGE & COUNTRY SELECTION - Please select the Language and Country. Some countries need to select the Time Zone. -
Page 7: Automatically For Setup
EZMANAGER Automatically for Setup From the TV Configuration Options screen, you can choose how to proceed with the configuration of this TV. Whether you will configure the TV for Pro:Centric operation via the wizard or use a USB memory device to configure the TV, you may first wish to set the Room Number on the TV. - If you intend to set Room Number as part of the TV configuration, use the Room Number option to assign the Room # for this TV before you continue with additional configuration. - Page 8 EZMANAGER This step automatically searches for the Pro:Centric Server. If was found the Pro:Centric data channel, select the ‘NEXT’ .
- Page 9 EZMANAGER Downloading the Pro:Centric application files takes few minutes. After the installation is completed, the following screen will be displayed.
-
Page 10: Manually For Setup
EZMANAGER Manually for Setup Select a Label and/or enter the Room Number using the numeric keypad on the remotes or using the virtual keyboard on the TV screen. To continue, move and select ‘NEXT’ . Please select the ‘MANUAL PRO:CENTRIC’ . - Page 11 EZMANAGER Configure the appropriate Pro:Centric settings in the TV.
- Page 12 EZMANAGER Downloading the Pro:Centric application files takes few minutes.
-
Page 13: Usb Lg Smart Install Utility
EZMANAGER After the installation is completed, the following screen will be displayed. USB LG Smart Install Utility Select the ‘USB CONFIGURATION’ →‘TV MANAGER’ . - If you have USB Memory for “LG_DTV” or “lg_dtv” folder, this step shows the USB file list for downloading the items. - Page 14 EZMANAGER - Detail information is described in TV Manager chapter of Installation Menu Downloading the files takes few minutes.
- Page 15 EZMANAGER After the installation is completed, the following screen will be displayed.
-
Page 16: Installation Menu
The abundant functions for Hotel TV linked with software installation can be projected on OSD as ‘Installation Menu’ . The wide range of hotel features can be performed simply on additional window to enhance the LG hotel TV’s easy installation and convenient operation for Hotelier and System Integrators. -
Page 17: Lg Hotel Mode
INSTALLATION MENU LG HOTEL MODE Use the button to select the LG HOTEL MODE SETUP. Use the ‘OK’ button and then button to select Hotel Mode Operation. - When ‘Hotel Mode Operation’ is set to On (Work), all functions of Hotel Mode apply. -
Page 18: Key Management
IR Operation y Decide whether work the LG remote control or not. - When ‘IR Operation’ is set to 'Normal' , all remote keys are available. - 'Use PWR Only' makes block all remote keys except power key. -
Page 19: Dtv Programme Update
INSTALLATION MENU Setup Menu - Permit to tune and manage programmes as 'On'(permitted) or 'Off'(not permitted). Programme Change y Decide to change channel or not by setting ‘Program Change' as ‘On’(Change Possible) or ‘Off’(Change Impossible) when present source is TV. - When ‘Programme Change' is set to Off (Change Impossible) »... -
Page 20: Aux Source Setting
INSTALLATION MENU Input - Set whether it is turned on by the set input source or by the last stored input source. Programme - Select start channel number if Input source’s value is TV. A/V Setting - If ‘A/V Setting’ is changed from ‘Off’ to ‘On’ , A/V parameters that are set before entering ‘Installation Menu’ are applied whenever turn on power. -
Page 21: Network
INSTALLATION MENU NETWORK button to select the NETWORK. Use the MAC Address - Displays the MAC address (not customizable). Network Setting One-click network connection - Connects easily to a wired/wireless network. - Network Connection to connect to an available network automatically. Follow the prompts on the TV. To connect to a network through Set Expert - For use in special circumstances such as in offices (in cases where a static IP is used). -
Page 22: Ip Stream Control
INSTALLATION MENU IP Stream Control Audio PTS Offset - Controlling output stream timing of audio. - You can set the '-500~500' (Change step is -10 or +10) Video PTS Offset - Controlling output stream timing of video. - You can set the '-500~500' (Change step is -10 or +10) IGMP - You can set IGMP version. -
Page 23: Worf
INSTALLATION MENU WORF - Press the ‘OK’ button in ‘WORF Setting’ item to go to the ‘WORF’ menu. - When WORF is set to ‘Enable’ , Hour and Minute items are enabled and then the WORF function is enabled. - When WORF is set to ‘Disable’ , ‘Hour’ and ‘Minute’ items are disabled and then the WORF function is disabled. Room Number Setting - Press the ‘OK’... -
Page 24: Room Number Setting
INSTALLATION MENU Room Number Setting - Press the ‘OK’ button in Room Number Setting item to go to the ‘Change a room number’ menu. - You can set or change Label and Room Number using the Room Number Setting. GENERAL Configuration Setup Select RCU - It is a mode to set whether to use Select RCU or not. - Page 25 INSTALLATION MENU • Type of Connector: D-Sub 9-Pin Male Signal Signal requirements RX RS232 Standard RS232 specification TX RS232 Standard RS232 specification IR from TV Power ground 6, 8 Not connected Male connector on box, viewed +5VDC 10%, max 100mV ripple towards connector.
- Page 26 INSTALLATION MENU DTV Programme Update - It is a mode to set whether to update DTV programme automatically or not. When DTV Programme Update is set to ’Auto’ , the function to update TV’s programme map according to dtv programme’s stream information. DTV Programme Update is set to ‘Manual’...
-
Page 27: External Speaker
INSTALLATION MENU External Speaker (Depending upon model) Volume Control - Selects the volume control method of an external speaker. You can select ‘Off’ , ‘Int Variable’ , ’ Fixed.’ , ’Ext Variable’ by pressing button. Ext Variable uses the External Vol Up/Down Control Line to change the volume up to 1 Watts. Int variable is linked to the main volume OSD and change the volume 0 - 1 Watts. -
Page 28: Hcec Setup
- You will have 3 modes to choose [Default], [HCEC] and [TVLink-CEC]. - If [Default] is selected, you can use SIMPLINK which is provided in LG TV. Also you can enable and disable SIMPLINK through SIMPLINK MENU. - If [HCEC] is selected, you can use TVLink-HCEC Protocol. For more detailed information, please refer to TVLink-HCEC Protocol document) - If [TVLink-CEC] is selected, TV will not directly work for key input except for power key. -
Page 29: Clock Setup
INSTALLATION MENU Clock Setup Clock Source - You can select ‘Off’ , ‘Pro:Centric’ , ‘TV’ , ‘NTP’ , ‘Admin’ by pressing button. - NTP : Clock is synchronized using Network Time Protocol. It's only enabled when network cable is connected. - Admin : It's automatically set to Admin when clock is updated by commercial protocols like TVLink-HCEC, TVLinkInteractive, or HCAP API. -
Page 30: Preloaded App
INSTALLATION MENU PreLoaded App If you want to use a particular app, you can choose from the menu. you can setting each apps activation. You can check or uncheck by pressing ‘OK’ button. Lock Mode - If ‘Lock Mode’ is ‘Yes’ , the following features will be unavailable. - If it is set to ‘Enable’... -
Page 31: Dmr
TV. - Supported device : Mobile device based on Android (higher than v4.4 Kitkat) / iOS * Support the lower than v4.4 (Kitkat) on the LG mobile device based on Android - Supported version : Higher than Bluetooth 3.0 DIAL - With this DIAL service, you can launch the target app at Smart Home Launcher bar without select the target app by remote controller. -
Page 32: Tv Manager
INSTALLATION MENU Wi-Fi Channel - You can control wireless channel on SoftAP mode. This is controlled from 1 to 11 channel. If you select ‘Auto’ , wireless channel of SoftAP will be set to random channel. TV MANAGER USB Download Menu * USB Cloning : An Installer can quickly set up and clone multiple TV sets at a property. - Page 33 INSTALLATION MENU Ez Download - Ez Download is a function that enables users to download the desired items all at once, such as EPK (software update file), TLL (see Export Clone File descriptions for more information regarding file types), Logo Image, etc (TLX, MICOM for Pro:Centric). Splash images and EPK files should be copied into the folder named LG_DTV on the USB.
- Page 34 INSTALLATION MENU Logo Image Download - If there are more than two USB Memory Device, It is possible to select the USB. - The download sequence is Logo Image Download → Select Image → UPDATE. NOTE Splash Image update function supports only JEPG,BMP format file of less than 8 MB filesize. We recommend you that splash image resolution match the TV`s panel resolution.
- Page 35 INSTALLATION MENU Update TV Software - This feature update EPK of TV through the hex file in USB. The target file is located in \LG_DTV folder. - If there are more than two USB memory Device, It is possible to select the USB. - The download sequence is Update TV Software →...
- Page 36 INSTALLATION MENU Update Micom Software - This feature update MICOM of TV through the hex file in USB. The target file is located in \LG_DTV folder - If there are more than two USB memory Device, It is possible to select the USB. - The download sequence is Update Micom Software →...
- Page 37 INSTALLATION MENU Import Clone File - Once the internal TV data and its channel map information is written to the USB memory card, the user can start “Import Clone File” process with the data file generated and stored in USB memory card. As previously warned in “Export Clone File” process, the user should not turn TV off nor unplug the USB memory card.
- Page 38 INSTALLATION MENU Export Clone File - "Export Clone File” must be done first before “Import Clone File” process, as it generate the file to be used in “Export Clone File”. While writing is in process, the user must not turn TV off nor unplug the USB memory card. The steps in “Export Clone File” are explained below. The following images might be slightly different than the OSD image.