Black & Decker HRV415B Instruction Manual page 5

Fig. D
Automatically charge (Fig. E, F)
iMPORTAnT: The power switch
position (I) for the vacuum to charge.
1. Plug the battery charger
2. Slide the jack plug 22
dock's charging socket
3. Place the charging dock base on a leveled floor with the
back of the charger against a wall.
nOTE: Do not place anything under the charging dock. It
will prevent the vacuum from automatically charging.
nOTE: Provide a minimum of 48 inches (122 cm) of clear
space around the dock.
Fig. E
15
23
4. Place the vacuum on the charging dock so that the
charging electrodes
17
plates 7 as shown in Figure F.
5. The Start/Stop button
short beep, indicating the vacuum is charging. The
Start/Stop button LED will turn off when the vacuum is
fully charged.
nOTE: You can check the charging status of the vacuum from
your BLACK+DECKER app.
nOTE: In SPOT and QUICK CLEAN Mode, the vacuum will finish
its cleaning cycle and stop and not return to the dock, unless
battery level is low, in which case it will search for the dock.
nOTE: In AUTO MODE, the vacuum will search for the
charging dock when it is low on battery charge. However,
if the room is too large or the vacuum is obstructed from
"seeing" the dock, it may fail to find the dock to automatically
recharge. If this occurs, place the vacuum on the charging
dock as described above.
Fig. F
3
2
MUsT be in the ON
1
18 into a wall outlet.
end of the charger into the charging
as shown in Figure E.
23
28
22
contact the two charging
3 will blink and emit a single
17
Using the BLACK+DECKER App to operate
your robot vacuum
The BLACK+DECKER App allows you to operate and connect
to your robot vacuum from a compatible mobile device.
After downloading the App, you connect your device to the
vacuum. Then you can use the App to operate the robot.
nOTE: Your mobile device has to be within Bluetooth range
22
to operate the robot
You can use the BLACK+DECKER App to:
• Schedule an auto cleaning to occur on the days and
times of your choosing.
nOTE: If at any time, the robot is switched to the OFF
position, the scheduling function will need to be restored
by reconnecting to the app after the unit has been turned
back on.
• Initiate a quick, spot, or manual cleaning.
• Monitor the robot's battery charge level.
• Add another BLACK+DECKER robot vacuum to your device.
• View Troubleshooting FAQ for suggestions on how to
solve common problems or errors.
• Create an account to receive promotional materials.
• Disconnect your device from the robot.
To download the BlACK+DECKER App and connect
your device, do the following:
1. Download the BLACK+DECKER App, application at:
2. Double-click the BLACK+DECKER App icon to launch the
App on your device. An App TERMS AND CONDITIONS
page appears.
nOTE: The BLACK+DECKER App is governed by separate
terms and conditions available for viewing through the
mobile application.
3. Scroll down the App TERMS AND CONDITIONS page to
make the Agree button clickable.
4. Click the Agree button to continue. A CREATE ACCOUNT
page appears.
5. Take one of the following options on the CREATE
ACCOUNT page:
- Complete and Submit the form if you want to create
a Stanley Black & Decker (SBD) user account. SBD
will send promotional emails to the email address
you specify.
- Click Skip to continue without creating an SBD
user account.
6. ANDROID ONLY; iOS SKIP to the next step. When the
Quick Setup screen appears, ensure that the "Enable
Bluetooth", "Location Services", and "App Permissions"
boxes are checked, and click Continue.
7. On the Select Product screen, click the Robot Vacuum
icon to connect the robot vacuum to your mobile device.
IMPORTANT: The power switch
position (I) for the vacuum to pair
8. When the Connecting screen appears, press and
hold the Start/Stop button
to connect your mobile device to the vacuum. A
confirmation message appears when the connection
English
1 MUST be in the ON
3 on the robot vacuum
5