Advertisement
Quick Links
Owner's Guide and Installation Manual
Attach sales receipt to this card and retain as your proof of purchase
DATE OF PURCHASE:
MODEL NUMBER:
To register your fixture, please visit our website www.montecarlofans.com
6LFR62XXXD Series Fan
cETL Model NO. : 6LFR62
RETAILER NAME:
RETAILER ADDRESS:
9.94 kg
21.87 lbs
Total fan weight with light
Advertisement
Related Manuals for Monte Carlo Fan Company 6LFR62 D Series
Summary of Contents for Monte Carlo Fan Company 6LFR62 D Series
- Page 1 Owner’s Guide and Installation Manual 6LFR62XXXD Series Fan cETL Model NO. : 6LFR62 Attach sales receipt to this card and retain as your proof of purchase DATE OF PURCHASE: RETAILER NAME: RETAILER ADDRESS: MODEL NUMBER: To register your fixture, please visit our website www.montecarlofans.com 9.94 kg 21.87 lbs Total fan weight with light...
-
Page 2: Cautions And Warnings
Cautions and Warnings WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING READ AND SAVE THESE INSTRUCTIONS Installation work and electrical wiring must be done by qualified person(s) in accordance with applicable codes and standards (ANSI/NFPA 70), including fire-rated construction. - Page 3 Mounting bracket Before you begin installing the fan, Switch Before installing this fan make sure the Use metal outlet box suitable for fan power off at Service panel and lock outlet box is properly installed to the support and use only the screws provided service disconnecting means to prevent house structure.
- Page 4 Downrod Yoke Canopy Canopy bottom Yoke cover Place downrod over canopy, canopy Partially loosen downrod set screws from Thread lead wires and safety cable from bottom cap and yoke cover yoke at top of motor assembly. motor assembly through downrod. Cross pin Slot Screwdriver...
- Page 5 SAFETY CABLE INSTALLATION Wall Switch Black (Live) Power source White (Neutral) Blue (For Light) Ground/Green White (For Light) Red (Motor 1) Purple (Motor 2) Lag screw Safety cable Gray (Motor 3) Green/Ground Receiver Washer Black (AC IN L) Lock washer White (AC IN N) For Canadian installation and for USA fan Make wiring connections using wire connectors provided as indicated above.
- Page 6 Plate on motor Light pan Loosen 2 and remove one set screws Place light pan over lead wires Install the light pan. Align its key holes from the plate on motor as shown in with the set screws on the plate and illustration.
- Page 7 Install Blanking Plate Lexan shade Attach LED light fixture onto the light pan, Attach lexan shade by locating dimples in Isolate the quick connects with electrical aligning the holes on the LED light fixture light pan with grooves on the Lexan tape.
-
Page 8: Transmitter Operation
REMOTE CONTROL SETTING and OPERATION Transmitter Operation Remove the battery cover from the remote control transmitter and install battery, battery provided. Replace the cover. Note: Use 2 1.5V/AAA battery. Note: If not using for long period of time, remove battery to prevent damage to remote transmitter, and store the remote transmitter away from excess heat or humidity. - Page 9 The buttons on the remote control transmitter control the fan speed and light as follows. Fan speed 1 = minimum speed 2 = low speed 3 = medium low speed 4 = medium speed 5 = medium high speed 6 = high speed This button turns the fan off.
-
Page 10: Troubleshooting
Trouble Shooting or wiring. In some cases, these installation errors may be mistaken for defects. If you experience any faults, installation, please call our Customer Service Center at the number printed on your parts list insert sheet. Warning means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel. - Page 11 Jan.2021...