Table of Contents
Advertisement
P
ROGRAMMABLE
T
T
D
WO
ONE
EC
Press (or Press and hold in for one second) the PF key
assigned to "Two Tone Dec" to turn the 2-Tone Decoder
"On" or "Off" (toggle).
CW ID S
INGLE
Press (or Press and hold in for one second) the PF key
assigned to "CW ID Single" to send the station callsign,
via Morse Code, once. Programming of the callsign is
performed by your VERTEX STANDARD dealer.
CW M
1 - CW M
ESSAGE
Press (or press and hold in for one second) the PF key
assigned to "CW Message 1 - 8" to send a pre-pro-
grammed Morse Code message on the transmitted sig-
nal. Programming of the message(s) is performed by
your VERTEX STANDARD dealer.
DC P
S
OWER
AVE
Press (or Press and hold in for one second) the PF key
assigned to "DC Power Save" to turn the DC Power
Save feature "On" or "Off" (toggle).
When DC Power Save feature is set to "ON," activate
the various power save feature (determined from your
VERTEX STANDARD dealer) while the repeater oper-
ates from the Backup Power Source.
E
NCRYPTION
Press (or Press and hold in for one second) the PF key
assigned to "Encryption" to turn off the Optional En-
cryption Unit temporarily.
E
C
NCRYPTION
ODE
Press (or Press and hold in for one second) the PF key
assigned to "Encryption Code" to select the Encryption
Code (determined from your VERTEX STANDARD
dealer; require the FVP-35 Rolling Code Encryption
Unit).
K
L
EY
OCK
Press (or Press and hold in for one second) the PF key
assigned to "Key Lock" to lock the repeater's front panel
keys (except "Key Lock" key); this feature can be en-
abled to prevent repeater settings from being disturbed.
L
PTT
OCAL
Press (or Press and hold in for one second) the PF key
assigned to "Local PTT" to enable ("On") or disable
("Off") operation using a PTT switch connected to the
front panel's Microphone Jack.
4
F
UNCTION
8
ESSAGE
PF K
D
EY
ETAILS
M
ONITOR
Press (or Press and hold in for one second) the PF key
assigned to "Monitor" to cancel CTCSS and DCS squelch
decoding, so as to enable reception of signals present on
the channel that do not contain a matching CTCSS tone
or DCS code.
M
M
ONITOR
This function provides to "Monitor" to cancel CTCSS
and DCS squelch decoding, so long as the PF key as-
signed to "Monitor M" is pressed and held in.
M
T
ULTI
ONE
Press (or Press and hold in for one second) the PF key
assigned to "Multi Tone" to switch the Tone Table be-
tween "Main" and "Sub."
P
I
ANEL
NDICATOR
Press (or Press and hold in for one second) the PF key
assigned to "Panel Indicator" to turn the Front Panel's
Illumination "On" or "Off" (toggle).
R
EMOTE
Press (or Press and hold in for one second) the PF key
assigned to "Remote" to toggle the operating mode be-
tween the "Remote" mode and "Local" mode.
When the "Remote" mode is selected, the repeater op-
erates according to the control instructions received
from the external device (connected to the ACC jack on
the rear panel). While in the "Local" mode, the repeater
operates from the front panel's PF keys.
R
EPEAT
Press (or Press and hold in for one second) the PF key
assigned to "Repeat" to toggle the operating mode be-
tween the "Repeater" mode and "Base Transceiver"
mode.
For normal operation, set this key to the "Repeat" mode.
When the "Base Transceiver" mode is selected, you can
speak into the microphone to use this repeater as a trans-
ceiver.
R
ESET
Press (or Press and hold in for one second) the PF key
assigned to "Reset" to reset (same function as the
POWER switch "off" and "on") the repeater.
VXR-9000 FM R
EPEATER
FCC ID: K6610443250/IC ID: 511B-10443250
O
M
PERATING
ANUAL
Vertex Standard Co., Ltd.
Advertisement
Table of Contents
