Table of Contents
Advertisement
D2E160-AH02-15
3.2 Nominal data
Motor
M2E074-LA
Phase
1~
Nominal voltage / VAC
230
Frequency / Hz
50
Method of obtaining
ml
data
Valid for approval/
-
standard
-1
Speed (rpm) / min
2500
Power consumption / W
550
Current draw / A
2.45
Capacitor / µF
12
Capacitor voltage / VDB
400
Min. back pressure / Pa
400
Min. ambient
-25
temperature / °C
Max. ambient
90
temperature / °C
ml = Max. load · me = Max. efficiency · fa = Free air
cs = Customer specification · ce = Customer equipment
Subject to change
3.3 Technical description
Weight
9.7 kg
Size
160 mm
Motor size
74
Rotor surface
Painted black
Impeller material
Sheet steel, galvanized
Housing material
Sheet steel, galvanized
Guard grille material
Steel, phosphated and coated with white-
aluminum plastic (RAL 9006)
Motor suspension
Motor vibration-damped on both sides
Direction of rotation
Counterclockwise, viewed toward rotor
Degree of protection
IP00
Insulation class
"F"
Moisture (F) /
F2-1
Environmental (H)
protection class
Installation position
Shaft horizontal
Condensation
None, open rotor
drainage holes
Mode
S1
Motor bearing
Ball bearing
Touch current
< 0.75 mA
according to IEC
60990 (measuring
circuit Fig. 4, TN
system)
Electrical hookup
Via terminal strip, capacitor connected
Motor protection
Thermal overload protector (TOP) with
basic insulation
with cable
Axial
Pollution degree
2
Protection class
I (with customer connection of protective
earth)
Item no. 11166-5-9970 · ENU · Change 88948 · Approved 2016-11-08 · Page 5 / 10
ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · info1@de.ebmpapst.com · www.ebmpapst.com
Operating instructions
Motor capacitor
according to EN 60252-
1 in safety protection
class
1~
Conformity with
230
standards
60
Approval
Comment
ml
-
2400
730
3.2
; Use the device in accordance with its degree of protection.
12
400
Information on surface quality
390
The surfaces of the products conform to the generally applicable industrial
-25
standard. The surface quality may change during the production period.
This has no effect on strength, dimensional stability and dimensional
50
accuracy.
The color pigments in the paints used perceptibly react to UV light over
the course of time. This does not however in any way affect the
technical properties of the products. The product is to be protected against
UV radiation to prevent the formation of patches and fading. Changes in
color are not a reason for complaint and are not covered by the warranty.
3.4 Mounting data
; Secure the screws against unintentional loosening (e.g. use self-
For screw clearance, see Chapter 3.1 Product drawing
Strength class of
screws
Any further mounting data required can be taken from the product
drawing or Section Chapter 4.1 Mechanical connection.
3.5 Transport and storage conditions
Max. permitted
ambient temp. for
motor (transport/
storage)
Min. permitted
ambient temp. for
motor (transport/
storage)
S0
EN 60335-1
CCC; EAC
Thermal overload protector with basic
insulation
With regard to cyclic speed loads, note that the rotating parts of
the device are designed for a maximum of one million load
cycles. If you have special questions, consult ebm-papst for
support.
locking screws).
8.8
+ 80 °C
- 40 °C
Advertisement
Table of Contents
