Advertisement
Quick Links
Advertisement
Related Manuals for Gallagher M12000i
Summary of Contents for Gallagher M12000i
- Page 1 FENCE ENERGIZER M6000i / M12000i Instructions - ENG...
- Page 2 3E5260 - Edi on 2 - February 2021 DISCLAIMER: Whilst every eff ort has been made to ensure accuracy, neither Gallagher Group Limited nor any employee of the company shall be liable on any ground whatsoever to any party in respect of decisions or ac ons they may make as a result of using this informa on.
-
Page 3: Table Of Contents
Contents Important Informa on ....................5 How the Energizer works ...................8 Installa on Guide ......................9 Understanding Your Energizer ...................12 Understanding Your Energizer Controller ..............13 Accessories ........................19 Troubleshoo ng ......................20 Waste Electrical And Electronic Equipment ..............20 Ed 1. -
Page 5: Important Informa On
• Regularly inspect the supply cord, cables, wires and energizer for any damage. If found damaged in any way, immediately cease use of the energizer and return it to a Gallagher Authorised Service Centre for repair in order to avoid a hazard. - Page 6 Important Informa on ver cal plane of the non-electrifi ed wires. The barbed wire and razor wire shall be earthed at regular intervals. • Follow the energizer manufacturer’s recommenda ons regarding earthing. • The energizer earth electrode should penetrate the ground to a depth of at least 1 m (3 ) and not be within 10 m (33 ) of any power, telecommunica ons or other system.
- Page 7 This energizer complies with interna onal safety regula ons and is manufactured to interna onal standards. Gallagher reserves the right to make changes without no ce to any product specifi ca on to improve reliability, func on or design. E & OE.
-
Page 8: How The Energizer Works
Gallagher 3E5260 M6000i/M12000i Energizer User Manual HOW THE ENERGIZER WORKS The energizer sends electrical pulses along the fence line, about one second apart. These pulses give the animal a short, sharp, but safe shock. The shock doesn’t harm the animal. It is suffi ciently memorable that the animal never forgets the shock, and will avoid the fence. -
Page 9: Installa On Guide
Gallagher 3E5260 M6000i/M12000i Energizer User Manual INSTALLATION GUIDE Energizer Controller Mount the controller on a fl at surface within 3m (10 ) of the energizer, or up to 50m (160 ) if using an RJ-12 extension cable*. The controller is suitable for indoor and outdoor use. - Page 10 Earth Stake (G879) and then clamp the exposed wire to each stake using an Earth Clamp (G876). Tighten the clamp. For further instruc ons on the earth (ground) system see the Gallagher Power Fence™ Manual. Note: Poor grounding can cause interference on telephone lines, radios and televisions.
- Page 11 Screw the terminal closed, ensuring the wire is fi rmly clamped. A ach the other end of the cable to the fence using a Joint Clamp (G603). For instruc ons on fence installa on see the Gallagher Power Fence™ Manual or go to www.gallagher.com.
-
Page 12: Understanding Your Energizer
Gallagher 3E5260 M6000i/M12000i Energizer User Manual UNDERSTANDING YOUR ENERGIZER Fence Fault LED Power On LED Flashing red when the Green when the energizer has detected a energizer is powered fence fault. Solid red when there is a sudden increase in fence load. -
Page 13: Understanding Your Energizer Controller
Gallagher 3E5260 M6000i/M12000i Energizer User Manual UNDERSTANDING YOUR ENERGIZER CONTROLLER Voltage Display Current Display Shows energizer / earth / fence zones voltage Shows the amount of load on the energizer / fence zones Status LED Quickscan Bargraph Provides quick indica on of the... - Page 14 Gallagher 3E5260 M6000i/M12000i Energizer User Manual Current Display The output current indicates how hard your energizer is working. When your fence is in good condi on this reading will be low, typically under 15 Amps. As the load on the fence increases the current will rise and output voltage will fall. The output current will typically change with fence condi ons, seasonal grass growth and wet weather.
- Page 15 Gallagher 3E5260 M6000i/M12000i Energizer User Manual Using The Energizer Controller Energizer Output and Alarms The energizer output is the default screen display mode. The zone indicator arrow is highligh ng the energizer zone ( ) and the energizer output voltage is 7.3KV in this case.
- Page 16 fi nd faults before your fence becomes ineff ec ve (voltage too low), Gallagher recommend se ng the current alarm 10A above normal opera on. Many events can cause the current to increase, including rainfall, grass growth, broken fences and failed insulators.
- Page 17 0.2-0.3KV is achieved. In dry condi ons or areas with low mineral content soil an earth return system may be required as described in the Gallagher Power Fence™ Manual or visit www.gallagher.com.
- Page 18 Gallagher 3E5260 M6000i/M12000i Energizer User Manual Fence Zone 1–6 View the Fence Zone performances by pressing the naviga on bu ons (< or >) un l the zone indica on arrow is highligh ng the desired fence zone (1–6). The fence zones voltage, current and alarm informa on is displayed in the same way as the Energizer output informa on.
-
Page 19: Accessories
Controller indica ng that zone is below the set alarm voltage. Gallagher Energizer Remote and Fault Finder G50700 The Gallagher Energizer Remote and Fault Finder displays which zone(s) are in fault and can then be used to locate the fault within that zone. Power to the fence at the fault loca on can be turned off... -
Page 20: Troubleshoo Ng
Gallagher 3E5260 M6000i/M12000i Energizer User Manual TROUBLESHOOTING Problem Causes Solution Energizer has started to run The internal temperature of Mount the energizer in a cool slowly the energizer is too high area, out of direct sun and with adequate ven la on. - Page 22 Gallagher Private Bag 3026, Hamilton, New Zealand...