Advertisement

Quick Links

Radio care
Warranty
The HT446E/L comes with a 12 month warranty,
for details see our full terms & conditions.
Advice
Do not use options or accessories not specified by
Entel
Ensure that the radio is used within the parameters
for which it was designed
Please switch the transceiver off before connecting
optional accessories
Warning
Turn the transceiver off in the following locations:
In explosive atmospheres (flammable gas, dust
including metallic & grain powders etc)
Whilst taking on fuel or while parked near
fuel station
Near explosives or blasting sites
In aircraft, medical institutions or near persons known
to be wearing a pacemaker
Caution
Do not disassemble or modify the transceiver for any
reason
Do not transmit while touching the antenna
terminal or any exposed metallic parts of the
aerial as this may result in a burn
Please check and observe regulations in your
country with regards to use whilst driving
Battery care
Introduction
Your Entel radio is supplied with a high performance
Lithium Ion (Li-Ion) battery. These batteries:
Extend talk time
Reduce the battery's size and weight
Do not suffer from 'memory effect' that reduces the
life of Ni-Cad and NiMH batteries
Have a low toxicity, therefore reducing the impact
on the environment
Battery Pack Precautions
Switch the transceiver OFF before charging
Charge the battery pack before use
Do not recharge the battery pack if it is already fully
End of Life Disposal
When your Entel transceiver reaches the end of its
useful life, please ensure that the unit is disposed of
in an environmentally friendly way. For country
specific information please see:
www.entel.co.uk/recycling
Cleaning your Radio
After exposure to any potentially corrosive substance
including salt water it is recommended to thoroughly
wash the transceiver in fresh water. If washing with the
battery removed from the radio, ensure that the battery
is not immersed in water & clean only with a damp cloth.
Note: Do not
wash the
transceiver if you
suspect the
waterproofing
seal may be
damaged.
Please return to
your supplier for
inspection /
repair.
charged. This could lead to a premature battery
replacement warning message (See Battery
Communications on page 4)
Charge the battery in accordance with the
instructions enclosed with your charger
Do not charge the transceiver and/or battery pack
if they are wet
The battery pack includes potentially hazardous
components. Please:
Do not disassemble or reconstruct battery
Do not short-circuit the battery
Do not incinerate or apply heat to the battery
Do not immerse the battery unless attached securly
to the radio in water or get it wet by other means
Battery care / information
Do not charge the battery near fires or under
direct sunlight
Use only the specified charger and observe
charging requirements
Do not pierce the battery with any object or
strike it with an instrument
Do not use the battery pack if it is damaged in
any way
Do not reverse-charge or reverse-connect the
battery
Do not touch a ruptured or leaking battery
If liquids from the battery get into your eyes,
immediately:
Wash your eyes out with fresh water avoiding
rubbing them.
Seek medical treatment
Battery Pack
If a battery is not to be used for an extended
period of time (e.g. several months) remove the
battery pack from the equipment and store in a
cool and dry location (around 0°C) part charged.
Ensure that the battery is recharged once every
three months and do not fully discharge the bat-
tery before storage.
Each charge cycle reduces the battery's life.
Minimise the number of times you charge your
battery especially in hotter environments which
further shortens a battery's life.
Battery Communications
Each battery used with your radio has a
microprocessor fitted, which logs the number of
times your battery has been charged.
On a radio with an LCD display, the number of times
the battery has been charged, together with the
remaining charge cycles available, will be shown
during switch on. On the advanced 8-key and 20-key
models, battery charge cycle information may also be
accessed via the menu. (If not de-activated by your
dealer)
The warranty on all batteries is 12 months or 450
charge cycles, whichever is the sooner. After 420
cycles, at switch on the radio will emit a series of
short tones, and on LCD models a waste bin icon
will flash to alert you to the need to buy a new
battery.
After 450 cycles, at switch on the radio will emit a
series of long beeps, and LCD models the message
will change to BATTERY COUNT EXCEEDED
REPLACE BATTERY. The radio will continue to
operate but its operational time may be reduced,
eventually failing all together.
Note: only genuine Entel batteries should be used.
Only genuine batteries offer the battery charge
count feature informing you when the battery is
reaching the end of its useful life. Customer
satisfaction is assured as you can not be supplied
with sub standard, potentially dangerous battery
packs from 3rd party manufacturers, ensuring it
delivers the expected capacity and endurance.
On HT series batteries a breathable membrane is
used. This is clearly marked on the battery label.
Piercing the membrane will allow water ingress to
the battery, and will invalidate the warranty.
4

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the HT446E/L and is the answer not in the manual?

Questions and answers

Summary of Contents for Entel HT446E/L

  • Page 1 Warranty End of Life Disposal • Do not charge the battery near fires or under The HT446E/L comes with a 12 month warranty, • When your Entel transceiver reaches the end of its direct sunlight for details see our full terms & conditions.
  • Page 2: Packing List

    Bluetooth double earpiece headband defender headset with boom mic and ear cup PTT • User guide CD * VOX = Voice Operated Transmit (hands free operation) For complete up to date list of optional accessories visit www.entel.co.uk Optional Accessories Preparing Your Radio For Use Battery & Charger Options...
  • Page 3: Using Your Radio

    Turn your radio on using the on / off power button on the front of the radio. The radio will “beep” and the LED will briefly illuminate yellow. (The beep may be disabled, if required, by your Entel approved dealer). Making a Call...
  • Page 4 To enable / disable the VOX feature, press the bottom side function button below the PTT button for 1 second. For a list of VOX compatible audio accessories see page 5 of this guide, contact your dealer or visit www.entel.co.uk...
  • Page 5: Controls And Indicators

    Programming your HT446E radio Controls & Indicators Dealer The radio’s frequency and tone configuration can be changed in user programming mode. This will Channel change control programmable allow you to put any of the standard frequencies or tones in to any channel position. When a radio button 3 Antenna has been configured this information can be quickly and easily cloned into other units using an...
  • Page 6 Check / Modify CTCSS/DCS Tone User Programmable Key Lock Checking the current configuration this action). The user programmable Key Lock function allows the Key Lock to be assigned to the lower side button and enabled \ disabled via the radio’s controls without the use of a computer. To check the entered setting, press the •...
  • Page 7: Frequency Table

    Radio Cloning HT446E Frequency Table Frequency Beeps • Radio cloning allows you to copy the programmed channel and button setup information from a 446.00625 MHz • • ‘master’ radio into other unprogrammed radios without the use of a PC. Cloning is performed by 446.01875 MHz •...
  • Page 8 DCS (DPL) Tone Table Beeps Beeps Beeps ▬ ● ▬ ● ▬ ● Intentionally Left Blank...
  • Page 9 Controls & Indicators HT446L All the features of the HT446E (see page 10) plus the following: Dealer Volume control Standard Features: programmable button 3 Antenna • LCD Display • Up to 255 programmable channel positions (8 RF channels) • Low battery indication on LCD dispaly Dealer programmable •...
  • Page 10: Lcd Indicators

    LCD Indicators Programming your HT446L radio The radio’s frequency and tone configuration can be changed in user programming mode.This will • Key Bleeps Off allow you to put any of the standard frequencies or tones in to any channel position.When a radio has been configured this information can be quickly and easily cloned into other units using an •...
  • Page 11 User Programmable Key Lock Radio Cloning HT446L The user programmable Key Lock function allows the Key Lock to be assigned to the lower side Radio cloning allows you to copy the programmed channel and button setup information from a button and enabled \ disabled via the radio’s controls without the use of a computer. ‘master’...
  • Page 12: Troubleshooting Guide

    Replace with genuine accessory Ch15 446.081250 CTCSS tone 85.4Hz Radio emits constant tone Incompatible battery fitted Replace with genuine Entel battery when switching on Ch16 446.093750 CTCSS tone 88.5Hz Below are in HT446L only Radio emits 5 short beep tones...
  • Page 13 Notes Notes Use this page to record important information, such as the serial number of your radio and any private channels programmed by your dealer etc.

Table of Contents