Military grade all-weather lcd displays (36 pages)
Summary of Contents for Marine PC MPC-SL19
Page 1
Marine PC MPC-SL19 USER MANUAL 19” IP-65 Marine Display Sunlight Readable LED B/L LCD (1st Edition 2009) All information is subject to change without notice. Approved by Checked by Prepared by Erik Hank Jack Page 1...
TABLE OF CONTENTS RECORD OF REVISION ......................2 TABLE OF CONTENTS ......................3 1.0 INTRODUCTION......................8 2.0 CONTROL AND FEATURES..................... 9 3.0 INSTALLATION ......................10 4.0 OSD OPERATION ....................... 16 5.0 TECHNICAL SPECIFICATION ..................28 Page 3...
Page 4
EMC conformance All MarinePC equipment and accessories are de signed to the best industry standards for use in the recreational marine environment. The design and manufacture of Marine PC equipment and accessories conform to the appropriate ElectroMagnetic Compatibility (EMC) standards, but correct installation is required to ensure that performance is not compromised.
Page 5
Packing List Before installation, please ensure the following items have been shipped: 1 x MPC-SL19 Marine Display 4 x Mounting bracket lugs and 4 stainless steel threaded studs 1 x Power Cable (5000 mm) 1 x VGA Cable (3000 mm) If any of these items should be missing or damaged, please contact your distributor or sales representative immediately.
Page 6
This Page Intentionally left Blank. Page 6...
Page 7
Usage Notice Precautions To maximize the life and safe use of your unit, always be sure to follow the warnings, precautions and maintenance recommendations in this user’s guide. In a Watercraft or Vehicle: The monitor should be visible to the driver only if it is used for navigation, or system control.
1.0 INTRODUCTION About MarinePC Marine Displays The MPC-SL19 is a high-performance marine Monitor, with optically bonded AR glass or sunlight readable touch screen, is especially engineered to survive the most demanding applications. You will soon become familiar with the quality difference in this bright sunlight readable (0.5 to 1,000 nits) monitor.
The MarinePC MPC-SL19 is designed to be mounted in two configurations: VESA75 / VESA100 MOUNT The MarinePC MPC-SL19 is designed compatible with VESA75 and VESA100 mount. By installing the monitor with this kit, the user can adjust the viewing angle to improve viewability in changing environments.
Page 11
Mounting holes on the MarinePC MPC-SL19 allow the monitor to be mounted by rear mounted using VESA75 or VESA100 mount PANEL (Flush) MOUNT For installation, there are four tapped mounting holes on the two sides of the unit’s panel. The mounting hardware packet is included with the product accessories in the shipping box.
Page 12
Installing the display 1. Carefully insert the monitor into the aperture, ensuring that your gasket on the rear of the fascia lays flat against the aperture edge. IMPORTANT: The gasket must lay flat against the aperture edge to ensure watertight integrity.
Page 13
Power requirements Your Sunlight Viewable display is designed to run on boat’s DC power systems rated at 12 V or 24 V. The MarinePC MPC-SL19 is equipped with 9~36V DC wide range power input. The DC power system should be either: •...
Page 14
Display location and mounting options Your display can be mounted using the flush mounting kit supplied. MarinePC recommends that you power the unit and select a suitable mounting location prior to installing the display. When planning the display location, the following points should be considered to ensure safe, comfortable and reliable operation: •...
4.0 OSD OPERATION Introduction Your MarinePC Sunlight Viewable display can be controlled using the On Screen Display (OSD) menu and/or the 8 buttons on the front bezel of the unit. The OSD menu enables you to change the way in which your display is set up and is accessed using the Menu button.
Page 17
BRIGHTNESS Key When you press the BRIGHTNESS Key, the screen will show the following image You can press the UP /DOWN Key to do the screen brightness adjustment. When the brightness achieve 50 and keeping pressing “UP” Key, the dimming will keep the brightness at 50.
Page 18
NIGHT MODE KEY When you press the “NIGHT MODE” KEY, the dimming will be down to under 0.5 nit directly. And if you press “BRIGHTNESS” KEY or “VR” knob at this moment, it will not function until you press the “NIGHT MODE” KEY again to release this restriction. When you press “MENU”, “DISP”, “PIP”...
Page 19
PIP KEY 1. Default main screen shows at RGB1 & RGB2 Press “PIP” KEY Figure 1 2. Default main screen stays at DVI1 & DVI2 Press “PIP” KEY Figure 2 3. Default main screen stays at VIDEO 1 Press “PIP” KEY Figure 3_1 4.
Page 20
When you enter the “PIP Port Change” screen, the status bar will remain at “OFF” position if you keep pressing the “DOWN” KEY to the end. At the other hand, the status bar will remain at top item of each menu if you keep pressing the “UP” KEY to the end.
Page 22
DVI 1 & 2’s setting screen: DVI Setting Item Description: ・ CONTRAST―――Contrast Adjustment。 ・ R_LEVEL――― Red Color level Adjustment。 ・ G_LEVEL――― Green Color level Adjustment。 ・ B_LEVEL――― Blue Color level Adjustment。 ・ TEMPERATURE――― Color Temperature Adjustment。 ・ DISP MODE――― FULL――― Full Screen。 EVEN―――...
Page 23
VIDEO 1 & 2 & 3’ setting screen: VIDEO Setting Item Description: ・ CONTRAST――― Contrast Adjustment。 ・ SHARPNESS――― Horizontal edge sharpness ・ HUE――― Color Adjustment ・ R_LEVEL――― Red Color level Adjustment。 ・ G_LEVEL――― Green Color level Adjustment。 ・ B_LEVEL――― Blue Color level Adjustment。 ・...
Page 24
PIP Sub-menu setting screen: PIP Setting Item Description: ・ PIP_SIZE――― Picture in Picture Screen Size Adjustment。 ・ CONTRAST――― Contrast Adjustment。 ・ R_LEVEL――― Red Color level Adjustment 。 ・ G_LEVEL――― Green Color level Adjustment 。 ・ B_LEVEL――― Blue Color level Adjustment 。 ・...
Page 25
OSD setting screen: OSD Setting Item Description: ・ H_POSITION―― Horizontal Screen Adjustment。 ・ V_POSITION―― Vertical Screen Adjustment。 ・ TRANSLUCENT――― Screen background color can be adjusted as transparent as you want (total 10 scales)。 ・ BRIGHTNESS――― Selection between “BRIGHTNESS” key or “VR” Button for brightness adjustment。...
Page 26
SYSTEM RETURN setting screen: You may choose “SYSTEM RETURN” selection item on the OSD Screen to restore all of the parameter setting to factory default value. When you press “UP” or “RIGHT” KEY, the parameter will show “YES” and confirm it. Page 26...
Page 27
“KEY LOCK” Mode Function setting screen: When you press “MENU” and “BRIGHTNESS” KEY simultaneously for 3 seconds, you will enter the “KEY LOCK” mode. At the same time, the screen will show “KEY LOCK” image as below for 5 seconds and then disappear. In the “KEY LOCK”...