Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for NODEXON NX-WC6008
Summary of Contents for NODEXON NX-WC6008
- Page 1 NX-WC6008 Wireless Controller Switch Product Guide...
- Page 2 This material is being distributed "as is." This document's contents are subject to change at any time without notice. Please visit the Nodexon Networks website for the most up-to-date information. Nodexon Networks makes every effort to guarantee content accuracy, but cannot be held liable for any losses or damages incurred as a result of content...
- Page 3 It is intended for the users who have some experience in installing and maintaining network hardware. At the same time, it is assumed that the users are already familiar with the related terms and concepts. Obtaining Technical Assistance Website:https://www.nodexon.com/ Technical Support Website:https://nodexon.com/support Community:http://www.nodexon.com/community Technical Support Email:support@nodexon.com Case Portal :https://www.nodexon.com/caseportal Website:https://www.nodexon.com/...
-
Page 4: Product Overview
1 Product Overview The NX-WS6008 wireless LAN controller is introduced by Nodexon Networks to provide powerful access control capability for medium-large-sized wireless networks. 1.1 NX-WS6008 Table 1-1 Technical Specifications of NX-WS6008 Model NX-WS6008 DDR3 SDRAM: 2GB Memory BOOTROM: 8MB FLASH: 128MB... - Page 5 Figure 1-2 Rear Panel of NX-WS6008 LED Indicators State Meaning The power module is NOT in the position or fails. Solid green The power module is operational. Blinking green The system is being initialized. Solid green The initialization process is complete. Solid red The system sends out an alarm.
-
Page 6: Preparation For Installation
Misuse of battery may cause damage to the device or hurt to people. Do not replace battery by yourself. Instead, contact Nodexon Service Center for the replacement of battery. This device is an A-class product. It may cause radio interference in living environment, which may require you to take anti-interference measures. -
Page 7: Cleanness Requirements
Long-time Working Short-time working Long-time Working Short-time Working Condition Condition Condition Condition 15ºC to 30ºC (59ºF to 86ºF) 0ºC to 45ºC (32ºF to 113ºF) 40%~65% 5%~95% The ambient temperature and humidity are measured at a point 1.5 meters (4.9 feet) above the ground and 0.4 meters (1.3 feet) before the device when there is no protective board in the front or back of the rack. -
Page 8: Anti-Interference Requirements
Maintain an appropriate humidity and temperature. Always wear an anti-static wrist strap when you touch any circuit board. Place the circuit board on an anti-static workbench or in an anti-static shielding bag. Try to hold a circuit board by its edges. Do not touch any components or the PCB. 2.2.4 Anti-Interference Requirements The wireless controller is susceptible to external interference such as electromagnetic wave and current. -
Page 9: Installation Flowchart
3 Installing Wireless Controller 3.1 Installation Flowchart Please follow the following procedure to install the wireless controller to ensure the smooth installation and avoid any damage to the device. Begin Read Chapter 2 Ensure Requirements are Met Mount Wireless Controller Connect Cables Verify Installation Power on Wireless Controller... -
Page 10: Installing Power Cable
3.2.2 Mounting NX-WS6008 on Workbench In the absence of a 19-inch standard cabinet, install the wireless controller on a clean workbench. During the operation, pay attention to the following items: The workbench is firm and well-grounded. The supplied plastic cushion is stuck to the small hole at the bottom of the wireless controller and a 10 cm clearance is reserved for dissipation. -
Page 11: Connecting Console
3.5 Connecting Console NX-WS6008 supplies an EIA/TIA-232 configuration console for local configuration. If you configure NX-WS6008 through Web, skip this part. Table 3-2 Console Attributes Parameter Description Connector RJ-45 Interface Standard Asynchronous EIA/TIA-232 Baud Rate 57,600 bps, 115,200 bps, 9,600 bps (default) Command line interface Supported Services Connection to character terminals... -
Page 12: Configuration Guide
4 Configuration Guide 4.1 Setting up Configuration Environment When you use the wireless controller for the very first time, you will need to configure it through a console port as follows: As shown in the following figure, connect the serial port of a character terminal or microcomputer to the console port through an RS232 cable. - Page 13 Figure 4-3 Setting Communication Parameters for Serial Port. After building the configuration environment, you may power on the wireless controller 4.2 Powering on Wireless Controller 4.2.1 Verification Before Power-on Before powering on the wireless controller, please check the following items:...
-
Page 14: Verification After Power-On
If the power cable and the grounding cable are connected correctly. If the power supply voltage meets the requirement. If the configuration cable is connected correctly, the microcomputer or terminal is turned on, and the setting is complete. - Page 15 0.000000] Checking for the daddiu bug... no. 0.000000] Determined physical RAM map: 0.000000] memory: 000000000003f000 @ 0000000000dd1000 (usable after init) 0.000000] memory: 000000000f000000 @ 0000000000f00000 (usable) 0.000000] memory: 00000000d0000000 @ 0000000020000000 (usable) 0.000000] memory: 000000000ffff000 @ 00000000f0001000 (usable) 0.000000] memory: 000000030efff000 @ 0000000100001000 (usable) mount: Mounting /dev/sda1 on /var/storage failed: No such device or address Starting rg_lowmem_killer...
-
Page 16: Power Troubleshooting
5 Troubleshooting 5.1 Power Troubleshooting You may use the power indicator on the front panel to decide if the power supply system is operating normally. For description of indicators, see Chapter 1. If a fault occurs, check the following items: ...