Toshiba 27A45 Service Manual page 20

2-5: HORIZONTAL SIZE
1. Receive the monoscope pattern.
2.
Using the remote control, set the brightness and contrast
to normal position.
3. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (06) on the remote control to
select "H. SIZE".
4.
Press the VOL. UP/DOWN button on the remote control
adjust the H.SIZE becomes 10 ± 4%.
2-6: VERTICAL POSITION
1. Receive the monoscope pattern.
2. Using the remote control, set the brightness and contrast
to normal position.
3. Adjust the VR401 until the horizontal line becomes fit to
the notch of the shadow mask.
2-7: VERTICAL SIZE
1. Receive the monoscope pattern.
2. Using the remote control, set the brightness and contrast
to normal position.
3. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (07) on the remote control to
select "V. SIZE".
4. Press the VOL. UP/DOWN button on the remote control
until the SHIFT quantity of the OVER SCAN on upside
and downside becomes 9 ± 2%.
2-8: VERTICAL LINEARITY
NOTE: Adjust after performing adjustments in section 2-7.
After the adjustment of Vertical Linearity, reconfirm
the Vertical Position and Vertical Size adjustments.
1. Receive the monoscope pattern.
2. Using the remote control, set the brightness, contrast,
to normal position.
3. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (08) on the remote control to
select "V. LIN".
4. Press the VOL. UP/DOWN button on the remote control
until the SHIFT quantity of the OVER SCAN on upside
and downside becomes minimum.
ELECTRICAL ADJUSTMENTS
horizontal line
Notch
Shadow mask
Fig. 2-1
2-9: TRAPEZIUM
1. Receive the cross hatch signal from the Pattern
Generator.
2. Using the remote control, set the brightness and contrast
to normal position.
3. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (32) on the remote control to
select "TRAPEZIUM".
4. Press the VOL. UP/DOWN button on the remote control
until the both vertical lines of the screen become paralled.
2-10: PARABOLA CORR
1. Receive the cross hatch signal from the Pattern
Generator.
2. Using the remote control, set the brightness and contrast
to normal position.
3. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (30) on the remote control to
select "PARABOLA".
4. Press the VOL. UP/DOWN button on the remote control
until the right and left vertical lines are straight.
2-11: LEVEL
1. Connect the AC voltmeter to pin 6 of CP101.
2. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (33) on the remote control to
select "LEVEL".
3. Press the VOL. UP/DOWN button on the remote control
until the AC voltmeter is 75 ± 2mV.
2-12: SEPARATION 1, 2
Please do the method (1) or method (2) adjustment.
Method (1)
1. Set the multi-sound signal generator for each different L-
ch and R-ch frequency (Ex. L-ch=2KHz, R-ch=400Hz)
and receive the RF.
2. Connect the oscilloscope to the Audio Out Jack.
3. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (34) on the remote control to
select "SEP 1".
4. Press the VOL. UP/DOWN button on the remote control
to adjust it until the audio output wave becomes a fine
sine wave.
5. Press the CH UP button once the set to "SEP 2" mode.
Then perform the above adjustment 4.
D-2 27A45/27A45C