Download
Share
Print this page
EAW UXA4410 Manual
  1. Manuals
  2. Brands
  3. EAW Manuals
  4. Amplifier
  5. UXA4410 series
  6. Manual

EAW UXA4410 Manual

Hide thumbs Also See for UXA4410:

Advertisement

Quick Links

Download this manual
Line Array
Application Guide

Advertisement

loading
Need help?

Need help?

Do you have a question about the UXA4410 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for EAW UXA4410

Summary of Contents for EAW UXA4410

  • Page 1 Line Array Application Guide...
  • Page 2 Resolution Users will need to perform the following 2 help file. general tasks to properly put an EAW line source product into use. This manual includes Using EAW Resolution™ details for each task. EAW Resolution is the key to determining 1.
  • Page 3 Line Array Application Guide EAW Passive Line Array Products - KF810P Symmetry of Sources Symmetrical arrangement Phase Aligned LF Tuned of acoustic sources along spacing of LF components to a common axis for utmost extend pattern control without consistency throughout the need for enormous horns.
  • Page 4 Line Array Application Guide EAW Passive Line Array Products - KF810P Tel 800 992 5013 / +1 508 234 6158 www.eaw.com...
  • Page 5 Line Array Application Guide EAW Passive Line Array Products - SB818P|F Retractable Rigging 18in Premium Transducer For groundstack With wicked long excursion configuration 5.3in voice coil driver Cable Chases On front and back conceal wiring and rigging for clean look...
  • Page 6 Line Array Application Guide EAW Passive Line Array Products - SB818P|F Tel 800 992 5013 / +1 508 234 6158 www.eaw.com...
  • Page 7 Line Array Application Guide EAW Passive Line Array Products - KF210 CONFIGURATION Subsystem Transducer Loading 2x10" cone, 2.5" VC Vented 1x1.4" exit, 3" VC compression drivers Isophasic Wave Guide Operating Mode Amplifier Channels External Signal Processing Single-amp LF/HF DSP w/EAW Focusing™ & DynO™...
  • Page 8 Line Array Application Guide EAW Passive Line Array Products - KF210 Tel 800 992 5013 / +1 508 234 6158 www.eaw.com...
  • Page 9 8x KF810P-80 line items. It is quite clear how much more directive the vertical has become in this image and if we continue to add modules to the array, the effect will become more pronounced. Tel 800 992 5013 / +1 508 234 6158 www.eaw.com...
  • Page 10 125Hz across this listening area. If directivity at lower frequencies is required for the application, array length must be considered. Pairing with EAW UXA4410 Power Amplifier Below are the recommended configurations when using UXA4410 with line array products KF810P MODEL...
  • Page 11 Line Array Application Guide SB818P|F MODEL CHANNEL AMPLIFIER UXA4410 KF210 - Bi Amped MODEL CHANNEL AMPLIFIER UXA4410 Tel 800 992 5013 / +1 508 234 6158 www.eaw.com...
  • Page 12 KF810P is a 3-way line array product, utlizing a passive crossover between the MF/HF. When wiring to UXA4410, utilize NL4 in outputs 1 & 3. Connect 2 pins +/- to LF, then the other 2 pins +/- to MF/HF into a Phoenix connector (which can then plug into the KF810P input). It's possible to loop 2 more cabinets in the same manner using Loop Thru.
  • Page 13 1 only is utilzed. When in bi amped mode, pin 1 +/- is LF, and pin 2 +/- is HF. When wiring to use with UXA4410 in single amp mode, plug NL4 into any output on the amp, then directly into the cabinet (NOTE: Pin 2 +/- will be unused).
  • Page 14 Line Array Application Guide Using UXA4410 Power Amplifier It is required to use an EAW amplifer with any EAW line array products. Important processing such as limiting, FIR filters, and DYNO (Dynamic EQ) is prudent to the loudspeakers performance. Tel 800 992 5013 / +1 508 234 6158...
  • Page 15 2. Power Switch– Applies mains power to the device. If the device has entered Sleep mode, it may be woken up again either from the EAW Resolution software application, or by switching this switch off, then on again. 3. Menu Buttons– There are three buttons to determine which section of the device to view or edit.

  • Page 16: Amplifier Output Connections

    9. Mute Buttons– DSP output mute status is indicated and controlled by an illuminated button for each channel. These flash when the entire unit is muted from the AUXA port or from EAW Resolution software Mute-All, or if this channel has been muted by the protection systems.
  • Page 17 More than one speaker can be connected to each channel provided the total impedance per channel is not less than 2 ohms. In bridged mode the minimum total impedance should not be less than 4 ohms. Tel 800 992 5013 / +1 508 234 6158 www.eaw.com...

  • Page 18: Load Matching

    Going Online with UXA4410 Before going online, assure the computer being used is connected to the same Ethernet network as the UX/UXA units. Two network cables will need to be connected to the processors/ amplifiers for Control and DSP (one to the ETHNET port, the other to one of the DANTE ports).
  • Page 19 To add a processor or amplifier to the system, click on the “+” symbol next to Processors & Amplifiers in the Project Explorer window. Upon being prompted, choose a name and a product from the devices available. Click “OK” once complete. Tel 800 992 5013 / +1 508 234 6158 www.eaw.com...
  • Page 20 The selected device will now be loaded into the system. In this case, as offline. To connect the processor or amplifier to the system, start by clicking Network > Connect. Tel 800 992 5013 / +1 508 234 6158 www.eaw.com...
  • Page 21 A prompt may appear if Resolution is not in sync with the device. Choose whether to push the Resolution settings to the device, or cancel to use the last known settings. Tel 800 992 5013 / +1 508 234 6158 www.eaw.com...
  • Page 22 Resolution settings to the device, or cancel to use the last known settings. At this point, the device is online and ready to use in the system (as indicated by the green light). Tel 800 992 5013 / +1 508 234 6158 www.eaw.com...
  • Page 23 3. Signal Routing: Assign input sources to input channels, or combine input sources to a single input channel. Select an input source type between Analog, AES3, and Dante (See both pull- down menus below). Tel 800 992 5013 / +1 508 234 6158 www.eaw.com...
  • Page 24 2. EQ/Filters Section: Manually adjust settings for all EQ/Filter bands. Use << >> buttons to navigate from one band to the next. There is an additional pull-down menu to choose type of filter. Once a Greybox is loaded, only the HPF may be modified. Tel 800 992 5013 / +1 508 234 6158 www.eaw.com...
  • Page 25 Line Array Application Guide 3. Greybox: Load EAW Greyboxes and set Input source (See pull down menu below). 4. Output Section: Adjust gain, invert polarity, and set delay or delay distance. Unity Gain and Invert Polarity is disabled once a Greybox is loaded.
  • Page 26 Line Array Application Guide Click any output channel, then click on Select/Configure Greybox. On the main Greybox Configuration window, click Add Greybox… Tel 800 992 5013 / +1 508 234 6158 www.eaw.com...
  • Page 27 Leg, Amp Type, Amp Gain, and Listener Distance. Either choose an available Amp Type or create one new by clicking on <New…> under the pull- down menu. Tel 800 992 5013 / +1 508 234 6158 www.eaw.com...
  • Page 28 Entry Method may either be by Voltage or Power. Back to the Greybox configuration window, the newly created amplifier will now be available on all channels under Amp Type. Click “OK” once complete. Tel 800 992 5013 / +1 508 234 6158 www.eaw.com...
  • Page 29 Dante card when Resolution is connected to the Ethernet port of a UX processor or UXA amplifier. The IP address of the Dante card is stored in the internal memory. This is only required once unless the internal Dante card is replaced. Tel 800 992 5013 / +1 508 234 6158 www.eaw.com...
  • Page 30 NOTE: Processor or Amplifier control will work fine without a unified Dante port. With the Unify Processors window open, select the processor and Dante interface that needs to connect. Click Unify to complete. Tel 800 992 5013 / +1 508 234 6158 www.eaw.com...
  • Page 31 After the function is complete, the linked interface may be viewed in the bottom pane as illustrated below. Click Done to accept or Break to undo and reverse the action. Under Online Devices, Resolution now associates the Dante card with the processor or amplifier. Tel 800 992 5013 / +1 508 234 6158 www.eaw.com...
  • Page 32 Rigging Hardware and Accessories Rigging EAW loudspeakers will invariably require hardware not supplied by EAW. Various types of load-rated hardware are available from a variety of third-party sources. There are a number of companies specializing in manufacturing hardware for, designing, and installing rigging systems.
  • Page 33 Position per Resolution 2 software. STINGER • Place flybar assembly on top of SB818P|F and use M8 X 30 bolts w/flat and lock washer to rig front and rear positions. Tel 800 992 5013 / +1 508 234 6158 www.eaw.com...
  • Page 34 Do so by laying the frame on a surface, then lowering SB818P|F array and attach using M8 X 22 bolts w/flat and lock washer to rig front and rear positions. NOTE: Orientation of KF810P adapter “Z” hole needs to be located to the rear of the array. Tel 800 992 5013 / +1 508 234 6158 www.eaw.com...
  • Page 35 To connect a second KF810P, repeat the same process but with M8 X 22 threaded bolt w/ flat and lock washers on front rigging. Repeat this process to use desired KF810P amount in array (see Resolution for array limitations). Tel 800 992 5013 / +1 508 234 6158 www.eaw.com...
  • Page 36 Select 0 deg (“Z”) position on rear rigging and use M10 bolt w/flat washers and lock nut to secure. • Attach shackle (¾ “) to desired stinger position and raise array (Use Resolution for optimal position). • Place second KF810P on surface underneath array and lower. Tel 800 992 5013 / +1 508 234 6158 www.eaw.com...
  • Page 37 The quantity recommendations below are for general purposes, providing a balanced system for most music applications. Quantities may need to be adjusted up or down for specific situations. Tel 800 992 5013 / +1 508 234 6158 www.eaw.com...
  • Page 38 • Place the first KF810P on top of frame, and secure front rigging with M8 x 22 bolts w/flat and lock washers (See Resolution for ground-stack limitations). Tel 800 992 5013 / +1 508 234 6158 www.eaw.com...
  • Page 39 Place frame on the ground. “Z” hole needs to be orientated towards the front of intended array. • Place the first KF810P on top of frame, and secure front rigging with M8x22 bolts w/flat and lock washers. Tel 800 992 5013 / +1 508 234 6158 www.eaw.com...
  • Page 40 Repeat this process to add additional KF810Ps, with rigging arm on KF810P beneath (See Resolution for ground-stack limitations). NOTE: Refer to chart on KF810P rigging or Resolution for KF810P to KF810P rigging angles. Tel 800 992 5013 / +1 508 234 6158 www.eaw.com...
  • Page 41 [4] of the first module. The next page shows in detail the fastening of the angle on the rear between the two modules. Tel 800 992 5013 / +1 508 234 6158 www.eaw.com...
  • Page 42 LOCK” position and release module B. This way, module B is completely blocked by the two pins on the rear. After assembly is completed, always make sure that all the pins have been completely inserted and are locked. Rear Rigging Assembly Plate Tel 800 992 5013 / +1 508 234 6158 www.eaw.com...
  • Page 43 Raise rigging ears on KF210 and align to flybar holes. • Insert front rigging pins on both sides. • Align and lock into place rigging plates on flybar to rear rigging assembly on KF210 module. Tel 800 992 5013 / +1 508 234 6158 www.eaw.com...
  • Page 44 Line Array Application Guide KF210 Carts • The KF210 Cart can transport up to 4x KF210 line array items. Tel 800 992 5013 / +1 508 234 6158 www.eaw.com...

  • Page 45: Warranty

    Line Array Warranty Application Guide These EAW products were designed and engineered at our headquarters in Whitinsville, MA USA and go through multiple quality checks during manufacturing. We guarantee our loudspeakers against defects in workmanship, materials and against malfunctions for a period of 6 years from date of delivery.