EAW CAM150 Instruction Manual

Integrated mixer/amplifiers

Hide thumbs Also See for CAM150:

Specifications (2 pages)

Table Of Contents

Table of Contents

Quick Links

150 /

CAM

Integrated Mixer/Amplifiers

CAM150-MIXER AMPLIFIER

��

INSTRUCTION MANUAL

CAM

��

"EAW" IS A REGISTERED TRADEMARK

��

OF LOUD TECHNOLOGIES INC.

��

� � � � � � �

��

�

��

�

��

�

��

�

��

�

��

Table of Contents

Need help?

Do you have a question about the CAM150 and is the answer not in the manual?

Questions and answers

Summary of Contents for EAW CAM150

Page 1 150 / Integrated Mixer/Amplifiers CAM150-MIXER AMPLIFIER �� INSTRUCTION MANUAL �� © 2004 LOUD TECHNOLOGIES INC. �� "EAW" IS A REGISTERED TRADEMARK �� OF LOUD TECHNOLOGIES INC. ��...
Page 2: Table Of Contents
C. The Component has been exposed to rain; or Part No. 0010169 Rev. A 02/04 © 2004 LOUD Technologies Inc. All Rights Reserved. – CAM150 / CAM60 D. The Component does not appear to operate normally or exhibits a AVIS marked change in performance;...
Page 3: Introduction
The CAM150 has a 150 watt power amplifier, and the CAM60 has 60 watts. Apart from this difference in power output, the two models are identical in details and operation.
Page 4: Front Panel Features
Turn down the Master Volume level so the top two LEDs do not light. – CAM150 / CAM60 6. POWER SWITCH Use this switch to turn the unit on or off. The power is on when the top of the switch is pressed, and off when the bottom is pressed.
Page 5: Rear Panel Features
�� CAM150 / CAM60 –...
Page 6 Make sure that the taps on the speakers add up to no more than 90% of the rated power for the amplifier being used CAM150: 135 watts, CAM60: 54 watts. CAUTION: To prevent the risk of electric shock, never touch the bare wires coming from the OUTPUT TERMINALS of the amplifier when it is switched on.
Page 7: Voltage Conversion
AC Mains has the same voltage as your unit, and is capable of supplying adequate current. Voltage Conversion The CAM150 and CAM60 can be configured to operate at 115 VAC or 230 VAC. Be sure the VOLTAGE SELECTOR switch located on...
Page 8: Xlr Connectors
XLR Connectors Inputs 1 to 4 can accept 3-pin male XLR connectors, wired as follows (according to standards specified by the Audio Engineering Society): – CAM150 / CAM60 XLR Balanced Wiring Pin 1 = Shield Pin 2 = Hot (+) Pin 3 = Cold (–)
Page 9: Typical Hookup Diagram
7. TYPICAL HOOKUP DIAGRAM CAM150 / CAM60 –...
Page 10: Specifications
Audio Outputs Number of Channels: Low Impedance: 4 Ω Constant Voltage: 25V, 70V, 100V Screw-terminal connectors CAM150 (4.5 Ω, 32.5 Ω, 66.5 Ω) CAM60 (10 Ω, 83 Ω, 170 Ω) Pre Out: One unbalanced RCA line-level output 1V/600 Ω Monitor Out: One terminal strip connection 1 watt/8 Ω...
Page 11: Block Diagram
9. SERVICE INFORMATION In the event that your CAM150 or CAM60 should require servicing, please follow these instructions: 1. Call EAW Commercial Tech Support at 1-888-337-7404, 7 am to 5 pm PST (Monday-Friday), to verify the problem and obtain a Return Authorization (RA) Number. Be sure to have the serial number of the unit when you call.
Page 12 EAW Commercial A LOUD Technologies Inc. Company EAW Commercial | One Main Street | Whitinsville, MA 01588 USA | TEL toll free within US/Canada 888.337.7404 TEL outside US 425.892.6503 | FAX 425.485.1152 | www.eawcommercial.com © 2004 LOUD Technologies Inc. All Rights Reserved.

This manual is also suitable for:

Cam60

EAW CAM150 Instruction Manual

Quick Links

Need help?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for EAW CAM150

Summary of Contents for EAW CAM150

This manual is also suitable for:

Table of Contents