Table of Contents
Advertisement
Quick Links
P a g e
| 1
PRODUCT MODEL NUMBER:
TL-9932 32 in 1 IP QAM
MODULATOR
ABOUT THIS
MANUAL
DISCLAIMER
No part of this document may be reproduced in any form without the written permission of the copyright
owner.
The contents of this document are subject to revision without notice due to continued progress in
methodology, design and manufacturing. TRANSLITE GLOBAL LLC shall have no liability for any error or
damage of any kind resulting from the use of this document.
COPY WARNING
This document includes some confidential information. Its usage is limited to the owners of the
product that it is relevant to. It cannot be copied, modified, or translated in another language
without prior written authorization from TRANSLITE GLOBAL LLC
Advertisement
Table of Contents
Related Manuals for TransLite TL-9932
Summary of Contents for TransLite TL-9932
- Page 1 The contents of this document are subject to revision without notice due to continued progress in methodology, design and manufacturing. TRANSLITE GLOBAL LLC shall have no liability for any error or damage of any kind resulting from the use of this document.
-
Page 2: Table Of Contents
P a g e INDEX TABLE OF CONTENTS CHAPTER 1 INTRODUCTION ........................3 1.1 PRODUCT OVERVIEW........................3 1.2 KEY FEATURES........................... 3 1.3 SPECIFICATIONS ..........................3 1.4 PRINCIPLE CHART ..........................5 1.5 APPEARANCE AND DESCRIPTION ...................... 6 CHAPTER 2 INSTALLATION GUIDE ...................... -
Page 3: Chapter 1 Introduction
CHAPTER 1 INTRODUCTION PRODUCT OVERVIEW TL-9932 32 in 1 IP QAM modulator is TRANSLITE Mux-scrambling-modulating all-in-one device. It supports maximum 1024 IP input through the 3 GE ports and 32 multiplexing scrambling QAM (DVB-C) modulating channels with non-adjacent carriers (50MHz~960MHz) output through the RF output interface. -
Page 4: Specifications
P a g e SPECIFICATIONS Input Input 512×2 IP input, 2*100/1000M Ethernet Port (SFP interface optional) Transport Protocol TS over UDP/RTP, unicast and multicast, IGMP V2/V3 Transmission Rate Max 840Mbps for each GE input Input Channel 1024 Output Channel Max PITranslite 256 per channel PID re-mapping (auto/manually optional) Functions... -
Page 5: Principle Chart
P a g e Constellation 16, 32, 64, 128, 256QAM RS (204, 188) RF Output Interface 1 F typed output port for 32 carriers, 75Ω RF Range 50~960MHz, 1kHz stepping Output Level -20dBm~+10dBm(87~117dbµV), 0.1dB stepping ≥ 40dB TS Output 32 IP output over UDP/RTP/RTSP, unicast/multicast, 2*100/1000M Ethernet Ports (SFP) System Network management software (NMS) supporting General... -
Page 6: Appearance And Description
P a g e Carrier Setting Illustration CH 2 CH X CH X CH 1 CH X CH 31 CH 32 ……… ……… 384M Start Frequency End Frequency APPEARANCE AND DESCRIPTION Front Panel Illustration NMS/CAS: network management port and CA data port Power Indicator... -
Page 7: Chapter 2 Installation Guide
ACQUISITION CHECK When user opens the package of the device, it is necessary to check items according to packing list. Normally it should include the following items: ➢ TL-9932 32 in 1 IP QAM Modulator ➢ User’s Manual ➢ Power Cord... -
Page 8: Installation Preparation
➢ Checking the possible device missing or damage during the transportation ➢ Preparing relevant environment for installation ➢ Installing TL-9932 32 in 1 IP QAM Modulator ➢ Connecting signal cables ➢ Connecting communication port (if it is necessary) DEVICE’S INSTALLATION FLOW CHART... -
Page 9: Grounding Requirement
P a g e Electric Isolation, Dust Free Machine Hall Volume resistivity of ground anti-static material: 1X107~1X1010， Floor Grounding current limiting resistance: 1M (Floor bearing should be greater than 450Kg/㎡) 5~40℃ (sustainable)，0~45℃ (short time) Environment Temperature installing air-conditioning is recommended Relative 20%~80% sustainable 10%~90% short time Humidity... -
Page 10: Frame Grounding
When the device adopts united way, the grounding resistance should be smaller than 1Ω. Caution: Before connecting power cord to TL-9932 32 in 1 IP QAM Modulator, user should set the power switch to “OFF”. -
Page 11: Web Nms Management
P a g e | 11 TL-9932 32 in 1 IP QAM Modulator cable illustration: • RF Input/Loop Cable Illustration: • NMS Cable illustration (CAT5): CHAPTER 3 WEB NMS MANAGEMENT User can only control and set the configuration in computer by connecting the device to web NMS Port. -
Page 12: Operation
P a g e | 12 192.168.99.252, we then change the device IP to 192.168.99.xxx (xxx can be 0 to 255 except 252 to avoid IP conflict). Launch the web browser an input the device IP address in the browser’s address bar and press Enter. - Page 13 P a g e | 13 Monitor → Input Status: Clicking “Input Status”, it will display the interface as Figure-3 where users can check the input status of Data1 and Data 2. Users need to add IP in “TS Config” part. Otherwise, it will monitor nothing.
- Page 14 P a g e | 14 Monitor → AC Checked: Clicking “AC Checked”, it will display the interface as Figure-5 where users can check scramble status. Figure-5 Parameters → TS Config: Clicking “TS Config”, it will display the interface where users can configure the output TS parameters in this interface.
- Page 15 P a g e | 15 ➢ Stream Select Clicking “Stream Select”, and click “+” to add IP input, then select one channel to parse, it will display the interface where users can choose the programs to Mux out. (Figure-7) Input Area Output Area Set output IP address of...
- Page 16 P a g e | 16 : To enable/disable the PID remapping To refresh the input program information To refresh the output program information Select one input program first and click this button to transfer the selected program to the right box to output. Similarly, user can cancel the multiplexed programs from the right box.
- Page 17 P a g e | 17 ➢ General Clicking “General”, it will display the interface where users can set parameters for each output channel. (Figure-9) Figure-9 ➢ PID Pass Clicking “PID Bypass”, it will display the interface as Figure-10 where user can add PIDs to be passed, click the “+”...
- Page 18 P a g e | 18 Figure-10 Parameters → Scrambler: Clicking “Scrambler”, it will display the interface where users can choose the programs to scramble. (Figure-11) Scramble channel select carrier select CA channel select EMMG and ECMG working state, green means it work normally, while red means...
- Page 19 P a g e | 19 Parameters → Modulator: Clicking “Modulator”, it will display the interface as Figure-12 where to set RF output parameters. Click “quickly config” to set all channels RF QAM output parameters Click “Channel config” to set each channel RF QAM output parameters Figure-12...
- Page 20 When users click “Channel config” button, it triggers a dialog box as follow where users can set the corresponding channel configration. Parameters → IP Stream: TL-9932 supports TS to output in IP (32*MPTS) format through the DATA port. Clicking “IP Stream”, it will display the interface as Figure-13 where to set IP out parameters. Quickly Config...
- Page 21 P a g e | 21 Set output IP address Click to enable the status and select TS out thru Data 1 or Data 2 When users click “Channel Config” button, it triggers a dialog box where users can set corresponding MPTS channel configration.
- Page 22 P a g e | 22 System → Password: Clicking “Password”, it will display the screen as Figure-15 where to set the login account and password for the web NMS. Figure-15 System → Configuration: Clicking “Configuration”, it will display the screen as Figure-16 where to set your configurations for the device.
- Page 23 P a g e | 23 System → Firmware: Clicking “Firmware”, it will display the screen as Figure-17 where to update firmware for the device. Figure-17 System → Date/Time: Clicking “Date/Time”, it will display the interface as Figure-18 where users can set date/time for this device.
-
Page 24: Chapter 4 Troubleshooting
CHAPTER 4 TROUBLESHOOTING All TRANSLITE products have been passed the testing and inspection before shipping out from the factory. The testing and inspection scheme already covers all the Optical, Electronic and Mechanical criteria which have been published by TRANSLITE. To prevent potential hazard, please strictly follow the operation conditions. -
Page 25: Chapter 5 Packing List
Device was suffered from physical damage ➢ Longtime idle. ➢ After switching on and restoring to factory setting, device still cannot work properly. ➢ Maintenance needed CHAPTER 5 PACKING LIST TL-9932 32 in 1 IP QAM Modulator User's Manual Power Cord... -
Page 26: Chapter 6 Applications
P a g e | 26 CHAPTER 6 APPLICATIONS...
Need help?
Do you have a question about the TL-9932 and is the answer not in the manual?
Questions and answers