Table of Contents
Advertisement
Controls I Contra/es I Contra/es
1
2
3
4
5
6
7
@
INPUT
BASS BOOST
LPF
HPF
SENSITIVITY
(VJ
LEVEL[dB)
FREGUENCY[Hz]
FREGUENCY(Hz]
D
Isl
IEl!EI
IEl!EI
IEl!EI
D
Isl
1
1
0.5 3 ( m f
21□□.
1~0
1<,0
190
2.
2
.
p.5
fl·
3·
•
1 •
•
ad
4
·o.:3
@
5
0.2
D
18
50
200
50
200
50
200
@
(MIN]
1MAx1
(MINI
(MAXltu=JIMINJ
IMAX)
(JU
[Ju
10
The unit is a S-channel amplifier
incorporating 2 stereo amplifi-
ers and 1 monaural amplifier in a
single body. The stereo amplifier
on one side is called amplifier
A,
while the one on the other side is
amplifier B. The monaural amplifi-
er is called the amplifier SUB. This
unit is compatible with a large va-
riety of systems by combining the
switches and functions described
in the following.
G)
Fuse (30 A
x
3)
I
NOTE
I
If
you can't
find the
specified
capacity
fuse at your
store
etc., consult
your
KENWOOD dealer.
@
Battery terminal (POWER IN
BATT.)
®
Power control terminal (P.CON)
Controls the
unit
ON/OFF.
©
Ground terminal (GND)
@
SPEAKER OUTPUT terminals
(A.ch/ B.ch)
• Stereo connections:
When you wish
to use
the
unit as a
stereo
amplifier,
stereo
connections
are used. The
speakers to be con-
nected
should
have
an
impedance
of
20
or
greater.
When
multiple
speak-
ers are to be
connected, ensure
that
the combined impedance is 20
or
greater
for each channel.
• Bridged
connections:
When
you
wish to use the unit
as
a
high-output amplifier,
bridged
con-
nections
are
used. (Make
connections
to the
LEFT channel
®
and the RIGHT
channel
0
SPEAKER OUTPUT
termi-
nals.)
The
speakers to be connected
~
'
---,
~
' ---,
~' ---,
11m I Dial
OFF
HPF
OFF
HPF
INPVT SELECTOR
I'll
F ILTER
la)
@
11
12
13
14
15
should
have an
impedance of 4 0 or
greater.
When
multiple
speakers are
to
be connected,
ensu
re
that
the
com-
bined
impedance
is
4 0 or greater.
@
SPEAKER OUTPUT terminals
(SUB)
As this
un it
accepts
speakers with
a
minimum impedance
of 2 ohms, con-
nect
speakers
with
2-ohm or
hig
her
impedance to
these
terminals.
(J)
SP LEVEL INPUT terminal
The output
from the FACTORY
INSTALLED
HEAD
UNIT
up
t
o
50
W
can
be input. The
power
is
turned
on
and
off as the unit detects
input
signal
(SIGNAL
SENSING TURN-ON).
Therefore
it is not
necessary to con-
nect the
power control w
ire.
@
REMOTE terminal (SUB)
(for separately available part
KCA-RC01A)
This
terminal
is an exclusive
terminal
for
a controller to adjust the volume
of the SUB
output.
®
LINE IN terminal (A.ch/B.ch/
SUB)
@
INPUT SENSITIVITY control
(A.ch/B.ch/SUB)
Set
this
con tro
l
accord
ing to
the
pre-output
level
of
the
HEAD UN
IT
connected w
ith this
un
it.
I
NOTE
I
For the pre-output
level, refer
to
the
"Specifications"
in the
instruction
manual
of
the
HEAD
UN IT.
@
INPUT SELECTOR switch
Set
this
switch
according to the
con-
nection
with this unit.
• A B position:
Select
"A
B" when there is no
connection
to
the SUB
input.
SUB out-
put
signal
is created
by this
unit.
• SUB
position:
Select
"SUB"
when
there
is con
nection
to the
SUB
input.
@
BASS BOOST LEVEL control
(SUB)
Sets the low frequency level
to
be
compensated.
@
LPF FREQUENCY control (SUB)
Th is con
t
rol adjusts the frequency
band output from this
unit.
@
FILTER switch (A.ch/B.ch)
Th is
swit
c
h
allow
fi ltering of the
speaker output signals.
• HPF (High-Pass Filter) position:
The
fil
ter outputs the band
of
higher
frequenc ies than the frequency
set
w
ith the
"HPF FREQUENCY"
control.
• OFF position:
The
entire
bandwidth is output with-
out
filtering.
@
HPF FREQUENCY control
(A.ch/ B.ch)
Th is con trol adjusts
the
frequency
band
output from this
unit.
@
Power indicator
W hen
the power
is turned
on,
the
Power indicator
lights.
8
9
@
~
KENWOOO
@
16
Hide quick links:
Advertisement
Table of Contents
