Table of Contents
Advertisement
Quick Links
OPERATING GUIDE
CCD CAMERA
IK-53V/IK-52V
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must ac-
cept any interference received, including interference that may cause undesired operation.
INFORMATION
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own ex-
pense.
USER-INSTALLER CAUTION: Your authority to operate this FCC verified equipment could be
voided if you make changes or modifications not expressly approved by the party responsible for
compliance to Part 15 of the FCC rules.
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est comforme à la norme NMB-003 du Canada.
Advertisement
Table of Contents
Related Manuals for Toshiba IK-53V
Summary of Contents for Toshiba IK-53V
-
Page 1: Operating Guide
OPERATING GUIDE CCD CAMERA IK-53V/IK-52V FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must ac- cept any interference received, including interference that may cause undesired operation. -
Page 2: Table Of Contents
1. GENERAL ...2 2. CAMERA PARTS AND FUNCTIONS ... 3 3. CONNECTIONS ... 5 4. SETTING ...6 4-1. Video Scanning Modes ...6 4-2. Electronic Shutter ...8 4-3. Reset Restart ... 9 4-4. External Trigger Mode ... 10 5. Input Output Signal Specifications ... 15 6. -
Page 3: General
1. GENERAL The IK-53V/IK-52V is a monochrome video camera using a solid image sensor CCD (Charged Coupled Device). High Picture Quality The VGA-applicable CCD of 330,000 pixels provides a fine picture equivalent to VGA. The square pixel CCD eliminates the necessity of conversion to aspect ratio when processing im- ages. -
Page 4: Camera Parts And Functions
2. CAMERA PARTS AND FUNCTIONS Top/Bottom/Front Side [Top] [Bottom] [Front] Lens mount (C mount) This is used to mount a C-mount type lens or optical equipment. Camera fixing reference hole (top side) Camera fixing reference hole/Tripod fixing metal screw hole (bottom side) Camera fixing reference hole/Tripod fixing metal screw hole (bottom side) Imaging area... - Page 5 Rear Side HD/VD VIDEO OUT DC IN/SYNC VIDEO OUT DC IN/SYNC plug (12-pin connector) This receives +12 VDC, and sends a video signal from the camera. When a synchronizing signal generator is connected to this plug and an external synchronizing signal (HD/VD signal) is applied, the camera can be operated synchronously with the external signal.
-
Page 6: Connections
PART input (signal) VIDEO INDEX output – (signal) – VD input (GND) Reset (GND) Camera Cable (optional) IK-53V IK-52V Connector: HR10A–10R–12PB by HIROSE electronics Co. Ltd Reset restart External trigger mode DC+12V Video output (GND) Video output (signal) HD input (GND) -
Page 7: Setting
4. SETTING 4-1. Video Scanning Modes This camera has two types of video signal scanning modes. Select the mode with the partial scanning switch (MODE SELECT switch bit 9) located and the setting of Pin 9 (PART input) of the 12-pin connector on the rear panel of the camera. Rear HD/VD VIDEO OUT... -
Page 8: Partial Scanning On
Partial Scanning ON In this mode, the pixel signal of the vertical center portion from the VIDEO OUT connector is output each 1/180 second. External HD/VD sync is permitted. 1/180s (175H) When Partial Scanning Mode is ON Video output Blanking interval Video interval Blanking interval 134H... -
Page 9: Electronic Shutter
4-2. Electronic Shutter This can be set with the MODE SELECT switch located on the rear panel. Description of the MODE SELECT Switch Rear HD/VD VIDEO OUT DC IN/SYNC M GAIN *The electronic shutter cannot be used in the reset-restart operation. Normal Shutter This mode permits a high-speed moving subject to be captured clearly with a shutter function incorporating a continuously available video signal. -
Page 10: Reset Restart
4-3. Reset Restart Input of an external reset-restart signal (VD) permits one screen of information to be output at an arbitrary timing. To set this mode, set the external trigger mode selection switch (i.e., MODE SELECT switch bits 5, 6, and 7) as illustrated in the diagram below. Rear HD/VD VIDEO OUT... -
Page 11: External Trigger Mode
4-4. External Trigger Mode Input of an external trigger permits a high-speed moving object to be captured at the proper position. Set the rear panel external trigger mode selection switch (i.e., MODE SELECT switch bits 5, 6, and 7) as illustrated in the diagram below. REAR HD/VD VIDEO OUT... - Page 12 • Pulse Width Trigger Mode (Setting by Trigger Pulse Width) Set all dip switches (1 to 4) of the rear panel to “OFF”. An arbitrary shutter speed is obtained by setting the width of the trigger pulse to 2 s or greater.
- Page 13 • Pulse Width Trigger SYNC-NON RESET Picture Output Timing (At Time of One-shot or Continuous External VD/Continuous External HD Input) Trigger* About 1 s Exposure period* External HD IN* External VD IN* (Internal VD) VIDEO INDEX Video output *1: Externally input signal *2: Exposure time = Trigger pulse width + 6 s (Valid trigger pulse width is 2 s or greater for external trigger shutter operation.) *3: Video is output at the falling edge of the internal VD following completion of the exposure...
- Page 14 • 1 Pulse Trigger SYNC-NON RESET Picture Output Timing (At Time of One-shot or Continuous External VD/Continuous External HD Input) Trigger* About 1 s Exposure period* External HD IN* External VD IN* (Internal VD) VIDEO INDEX Video output 525H (Partial scanning OFF) 175H (Partial scanning ON) *1: Externally input signal *2: Exposure time is determined by the setting of the MODE SELECT switch.
- Page 15 • 1 Pulse Trigger SYNC-RESET Picture Output Timing Trigger* VD OUT Video output VIDEO INDEX *1: Externally input signal *2: Exposure time is determined by the setting of the MODE SELECT switch. Refer to page 10. *3: VD is generated after 0 to 1H following the completion of the exposure period and the video is synchronized to this and output.
-
Page 16: Input Output Signal Specifications
5. Input Output Signal Specifications HD/VD Output Amplitude Specifications The amplitude level is the representative value when terminated with 10k . Output is enabled when the rear panel HD/VD signal input/output switch is set to the INT side. VIDEO INDEX Output Specifications 525H (Partial scanning OFF) 175H (Partial scanning ON) The amplitude level is the representative value... - Page 17 External HD/VD Input Phase Specifications External HD rising edge External HD The phase relationship of the external HD and VD should correspond to the center phase (i.e., the external HD falling edge) as illustrated in the above diagram. External VD falling edge: Please input within about 100 clock cycles of the standard center phase.
-
Page 18: Ccd Output Waveform Timing Chart
6. CCD Output Waveform Timing Chart Horizontal Output Waveform Timing Chart output signal Horizontal blanking interval 132clk Video output signal (Representative values) 18clk (0.73 s) Vertical Output Waveform Timing Chart (286 s) output signal Dummy pixels Video Vertical blanking interval 20H output signal (Representative values) -
Page 19: Exterior View
7. EXTERIOR VIEW IK-53V R0.3 (whole circumference) 29 [1.14"] IK-52V R0.3 (whole circumference) 29 [1.14"] 2-M2 depth 2.5 [0.10"] R0.3 (whole circumference) 14.5 [0.57"] 12.5 [0.49"] 29 [1.14"] 7.9 [0.31"] 3 [0.12"] 11.6 [0.06"] 3.8 [0.15] 14.8 [0.58"] 23.7 0.1 [0.93"] 22 0.1 [0.87"]... -
Page 20: Specifications
Progressive Scanning 1/3 inch CCD (IK-53V) Progressive Scanning 1/2 inch CCD (IK-52V) 659 x 494 (H/V) 5.84 x 4.94mm (IK-53V), 7.48 x 6.15mm (IK-52V) H: 31.469 kHz, V: 59.94Hz Internal/external (HD/VD) (HD/VD input/output area selected by the switch on the rear panel.) - Page 21 Spectral Sensitivity Characteristics (Representative Values) (Including lens characteristics, excluding light source characteristics) IK-53V IK-52V Wave length (nm) Wave length (nm) 1000 1000...