Advertisement
JP1
1: PSU Jumper
Link
A
B
Position A: Sounder PCB is
powered from panel via ribbon cable.
Position B: Sounder PCB is
powered from external PSU (see
Specification).
+ 1 -
+ 2 -
+ 3 -
+ 4 -
+
-
JP1
A
B
TB1
TB2
TB3
PL2
FS02 DEOL MON. SOUNDER PCB
3: DIP Switch - Circuit Configuration Functions
DIP switch Settings
Option
1 2 3 4
0
0 0 0 0
1
1 0 0 0
2
0 1 0 0
3
1 1 0 0
4
0 0 1 0
5
1 0 1 0
6
0 1 1 0
7
1 1 1 0
8
0 0 0 1
9
1 0 0 1
10
0 1 0 1
11
1 1 0 1
12
0 0 1 1
13
1 0 1 1
14
0 1 1 1
15
1 1 1 1
4: Other Configuration Options
DIP switches: 5-8 settings
5 6 7 8
0 0 0 0
1 0 0 0
0 0 0 0
0 1 0 0
0 0 0 0
0 0 1 0
0 0 0 0
0 0 0 1
2: External PSU
R63
Earth Link
If an external PSU with its output
referenced to earth is used (i.e.
continuity between mains earth and 0V),
remove R63 to isolate the input. This
prevents earth faults from occurring.
1
2
!
0V
PL1
TB4
1
SW1
1
2 3 4 5 6 7 8
0
1 2 3 4 5 6 7 8
SK2
SK1
IN-CIRC
PROGR.
Circuit 1
Any zone
200R
200R
Any zone
Any zone
Any zone
Zone 1
Zone 5
Zone 1
Zone 2
Zone 1 or
Zone 2
Zone 1 and
Zone 2
Zone 1 and
Zone 3
Zone 2 and
Zone 4
Any zone
Key
Function
Steady/Pulsing
Steady sounders
Pulsing sounders, 1second on, 1 second off
Sounders > 250mA
Sounders > 250mA. Use this setting if one or more of the output circuits has a load current of 250mA or above.
Sounders < 250mA. Use this setting if none of the output circuits has a load current greater than 250mA.
Digital input circuit 1
Class change
Fire transmission confirmed (monitored fire routing output)
Digital input circuit 2
Day mode
Fault transmission confirmed (monitored fault routing output)
Fitting/Replacing the 4-Way Sounder PCB
Configuration Options
By default, the PCB is configured as follows:
All circuits are sounders, activated on first fire, any zone. Sounders steady
and load >250mA. Digital inputs set to Class Change and Day Mode.
If other options are required, configure links and DIP switch before fitting
the PCB into the panel. Perform configuration in the sequence given below:
1
Jumper link
Determine whether power is obtained from the panel or from an
external dc power supply unit (PSU) - refer to 'Specification' on page 4.
2
Earth link
Remove if the external PSU's output is referenced to earth.
3
DIP switch - circuit configuration functions
Use switches 1 to 4 to configure the four circuits.
1
4
DIP switch - other configuration options
0
Switch 5 determines whether the sounders are steady or pulsing.
Switch 6 must be set according to the maximum load current being
drawn on an circuit (if configured as an output). This is used by the PCB
to detect partial open and short circuits.
Switch 7 determines the function of digital input circuit 1.
Switch 8 determines the function of digital input circuit 2.
Functions
Circuit 2
Any zone
Return Signal
(unlatched)
Return Signal
(latched)
SST Fault
Any zone
RESET OUT
Zone 2
Zone 6
Zone 3
Zone 4
Zone 3 or
Zone 4
Zone 3 and
Zone 4
Zone 3 and
Zone 5
Zone 4 and
Zone 6
Any zone
Sounder activated on first fire in Zone n
Sounder delayed on first fire in Zone n
Sounder activated on second fire in
Zone n
3
Circuit 3
Any zone
SST Operated
Any MCP
Zone
Zone 3
Zone 7
Zone 5
Zone 6
Zone 5 or
Zone 6
Zone 5 and
Zone 6
Zone 5 and
Zone 7
Zone 6 and
Zone 8
Any zone
Fire Routing
Output
Fault Routing
Output
997-536-000-2, Issue 2 July 2009
Circuit 4
Any zone
Any zone
Any Detector
Zone
Zone 4
Zone 8
Zone 7
Zone 8
Zone 7 or
Zone 8
Zone 7 and
Zone 8
Any zone
Any zone
Any zone
ÜE
SST
Output
Output
ÜE
SST
Input
Input
Advertisement
