Advertisement
2
38
SUBMITTAL DATA | Series 1000 SM
UL/ULC Approved Smoke Damper
TAMCO® Series 1000 SM meets the require-
ments for smoke dampers established by:
UL 555S/ULC-S112.1 File R16679
National Fire Protection Association:
NFPA Standards 80, 90A, 92, 101, 105
California State Fire Marshall Listing#:
3230-2116:0100
MINIMUM OPENING SIZE:
11"w x 6"h
(280 mm x 153 mm)
MAXIMUM SINGLE-SECTION OPENING SIZE:
36"w x 48"h
(915 mm x 1220 mm)
MAXIMUM MULTI-SECTION OPENING SIZES:
144"w x 96"h
(3658 mm x 2438 mm)
288"w x 48"h
(7316 mm x 1220 mm)
PERFORMANCE DATA | Series 1000 SM
UL/ULC Approved Smoke Damper
VELOCITY VS.
PRESSURE DROP
AMCA Figure 5.3
1.0
0.5
0.1
.03
.01
100
500
Face Velocity (fpm)
LEGEND:
12" x 12"
24" x 24"
(305 mm x 305 mm)
(610 mm x 610 mm)
12" x 48"
36" x 36"
(305 mm x 1220 mm)
(915 mm x 915 mm)
INSTALLATION:
10. Smoke dampers may be mounted vertically (standing up/horizontal airflow) with blades
running horizontally, or mounted horizontally (lying down/vertical airflow).
11. Dampers are available in four install types: Installed In Duct, Flanged to Duct, Extended Rear
Flange, and Square to Round Transition. (See Install Types pages for details.)
12. Multi-section smoke dampers may require field assembly of sections.
13. Installation of dampers must be in accordance with TAMCO's current UL/ULC Approved
Smoke Damper Installation Guidelines, provided with each smoke damper shipment.
(Printed installation guidelines are provided with each damper shipment, however all
technical information available on TAMCO's web site at www.tamcodampers.com supersedes
information contained within printed versions.)
ACTUATORS:
14. UL 555S/ULC-S112.1 requires that all actuators for smoke dampers be factory mounted.
Approved actuators are Belimo and Honeywell.
15. Voltage:
16. Mounting: Internal or external actuator mounting. (All smoke dampers with internally
17. Options:
18. Actuator quantity and location requirements are shown in, and must be in accordance with,
TAMCO UL/ULC Approved Smoke Damper Configurations.
1,000
5,000
10,000
48" x 12"
(1220 mm x 305 mm)
www.tamcodampers.com
24 vac, 120 vac, 230 vac, single phase.
mounted actuators, will be mounted on a jackshaft. If actuator side of damper is to be
connected to duct work, smoke damper assembly will have to be installed in a sleeve.)
Auxiliary switches.
T.A. Morrison & Co. Inc. certifies that
the TAMCO Series 1000 SM UL/ULC
Approved Smoke Damper shown
herein is licensed to bear the AMCA
Seal. The ratings shown are based on
tests and procedures performed in
accordance with AMCA Publication 511
and comply with the requirements of
the AMCA Certified Ratings Program.
The AMCA Certified Ratings Seal
applies to air performance ratings.
FIG. 5.3
Test damper is fully ducted with a 5 diameter duct run
upstream, and a 6 diameter duct run downstream.
Pressure drop values are based on Flanged to Duct install type.
Pressure drop will be greater for In Duct install type dampers.
© T.A. Morrison & Co. Inc., 2016
TAMCO JUNE, 2016
Advertisement
