1
SUBMITTAL DATA | Series 1000 SM
UL/ULC Approved Smoke Damper
In Duct or
Flanged to Duct
Install Types
1"
25.4 mm
4"
101.6 mm
6.4"
162.6 mm
blades fully open
Extended Rear Flange
Install Type
1.06"
2"
27 mm
50.8 mm
Leakage Rating: Class 1
Operational
Rating:
Fail Position:
STANDARD CONSTRUCTION:
1. Extruded aluminum
thickness. Damper frame is 4"
sides of frame. Damper frame has a 2"
when ordered as Extended Rear Flange install type.
2. Blades are maximum 6"
blades are symmetrically pivoted.
3. Blade and frame seals are specially designed and engineered extruded silicone. Seals are
secured in an integral slot within the aluminum extrusions. Blade and frame seals are
mechanically fastened to prevent shrinkage and movement over the life of the damper.
4. Bearings are composed of a bronze oilite inner bearing - fixed around a
aluminum hexagon blade pivot pin - rotating within a bronze oilite outer bearing inserted in
the frame.
5. The
7
/
"
(11.11 mm)
16
zinc-plated steel. These provide a positive connection to blades and linkage.
6. Aluminum and corrosion-resistant zinc-plated steel linkage hardware is installed in the frame
side, complete with cup-point trunnion screws for a slip-proof grip.
7. Smoke dampers are designed for operation in temperatures ranging from -40°F
250°F
(121°C)
8. Smoke dampers are custom made to required size, without blanking off free area.
9. Smoke dampers are available with parallel blade action.
CONSTRUCTION OPTIONS:
For each option listed, replace the lines above with their corresponding lines below.
MR - MOISTURE RESISTANCE OPTION:
1. Extruded aluminum
thickness. Damper frame is 4"
sides of frame. Damper frame has a 2"
when ordered as Extended Rear Flange install type. Frame is assembled using stainless steel
screws.
7
5. The
/
"
(11.11 mm)
16
stainless steel. These provide a positive connection to blades and linkage.
6. Aluminum and stainless steel linkage hardware is installed in the frame side, complete with
cup-point trunnion screws for a slip-proof grip.
SW - SALT WATER RESISTANCE OPTION:
1. Extruded aluminum
thickness. Damper frame is 4"
sides of frame. Damper frame has a 2"
when ordered as Extended Rear Flange install type. Aluminum frame is clear anodized to a
minimum thickness of 0.7 mil
2. Blades are maximum 6"
anodized to a minimum thickness of 0.7 mil
5. The
7
/
"
(11.11 mm)
16
stainless steel. These provide a positive connection to blades and linkage.
6. Linkage hardware is installed in the frame side. All aluminum linkage hardware parts are clear
anodized. All non-aluminum linkage hardware parts are stainless steel. They are complete with
cup-point trunnion screws for slip-proof grip.
TAMCO® Series 1000 SM meets the require-
ments for smoke dampers established by:
UL 555S/ULC-S112.1 File R16679
National Fire Protection Association:
NFPA Standards 80, 90A, 92, 101, 105
California State Fire Marshall Listing#:
3230-2116:0100
www.tamcodampers.com
Airflow: 2000 fpm
(10.2 m/s)
Temperature: 250°F
(121°C)
Pressure: 4" w.g.
(1 kPa)
Closed
smoke damper frame is not less than 0.080"
(6063-T5)
deep x 1"
(101.6 mm)
(50.8 mm)
deep extruded aluminum
(152.4 mm)
hexagonal drive rod, U-bolt fastener, and hexagonal retaining nuts are
.
smoke damper frame is not less than 0.080"
(6063-T5)
deep x 1"
(101.6 mm)
(50.8 mm)
hexagonal drive rod, U-bolt fastener, and hexagonal retaining nuts are
smoke damper frame is not less than 0.080"
(6063-T5)
deep x 1"
(101.6 mm)
(50.8 mm)
deep. Frame is assembled using stainless steel screws.
(18 microns)
deep extruded aluminum
(152.4 mm)
(18 microns)
hexagonal drive rod, U-bolt fastener, and hexagonal retaining nuts are
© T.A. Morrison & Co. Inc., 2016
. Rated for airflow in either direction.
static pressure differential
, with mounting flanges on both
(25.4 mm)
mounting flange on the rear of the damper,
air-foil profiles. All
(6063-T5)
7
, with mounting flanges on both
(25.4 mm)
mounting flange on the rear of the damper,
, with mounting flanges on both
(25.4 mm)
mounting flange on the rear of the damper,
air-foil profiles, clear
(6063-T5)
deep. All blades are symmetrically pivoted.
in
(2.03 mm)
/
"
(11.11 mm)
16
to
(-40°C)
in
(2.03 mm)
in
(2.03 mm)
TAMCO JUNE, 2016