Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Elatec TWN4 MULTITECH NANO M
Summary of Contents for Elatec TWN4 MULTITECH NANO M
- Page 1 TWN4 MULTITECH NANO M INTEGRATION MANUAL...
-
Page 2: Table Of Contents
TABLE OF CONTENTS INTRODUCTION .................................. 3 ABOUT THIS MANUAL ..............................3 ABOUT TWN4 MULTITECH NANO M ........................... 3 ELATEC SUPPORT ................................ 3 REVISION HISTORY ..............................3 SAFETY INFORMATION ..............................4 INTEGRATION INSTRUCTIONS ............................5 GENERAL ..................................5 LIST OF APPLICABLE RULES ............................5 SPECIFIC OPERATIONAL USE CONDITIONS ...................... -
Page 3: Introduction
English will prevail. ABOUT TWN4 MULTITECH NANO M TWN4 MultiTech Nano M is designed for integration into machines or other devices. It can be connected to an external antenna through a printed circuit board (125 kHz, 13.56 MHz or both). -
Page 4: Safety Information
ELATEC technical documentation related to TWN4 MultiTech Nano M, as well as the technical documentation related to the host device. In particular, the instructions and safety information given in the user manual of TWN4 MultiTech Nano M should be read carefully and listed in the technical documentation of the host manufacturer as well, as soon as these instructions and safety information are required for a safe and proper use of the host device containing TWN4 MultiTech Nano M. -
Page 5: Integration Instructions
3 INTEGRATION INSTRUCTIONS GENERAL TWN4 MultiTech Nano M may be installed in any host devices, as long as it is operated under the operational conditions stated in the user manual and other technical documents (e.g. data sheet). LIST OF APPLICABLE RULES... -
Page 6: Rf Exposure Considerations
Lead free, coil fixed by using backed wire Please note that the use of TWN4 MultiTech Nano M with other antennas than the ones described above is not part of the approvals granted to the module. In case TWN4 MultiTech Nano M is used with other antennas, a separate approval, additional testing or new authorization for a use with these specific antennas is required. -
Page 7: Additional Testing, Part 15 Subpart B Disclaimer
ADDITIONAL TESTING, PART 15 SUBPART B DISCLAIMER TWN4 MultiTech Nano M is only FCC authorized for the specific rule parts (i.e., FCC transmitter rules) listed on the grant, and the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. -
Page 8: Compliance Statements
4 COMPLIANCE STATEMENTS TWN4 MultiTech Nano M is in compliance with the EU directives and regulations as listed in the respective declaration of conformity. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. -
Page 9: Integrator And Host Requirements
The FCC and IC identification numbers of TWN4 MultiTech Nano M can be found in Chapter “Compliance Statements” of the user manual and on the device packaging. After integration of TWN4 MultiTech Nano M into the host device, it is necessary to bring a label... -
Page 10: Appendix
Development Canada Apparatus (All Frequency Bands) For more information about this integration manual or TWN4 MultiTech Nano M, go to www.elatec.com or contact ELATEC. © 2022 ELATEC GmbH – TWN4 MultiTech Nano M integration manual DocRev4 – 04/2022 Page 8 of 11... - Page 11 Elatec reserves the right to change any information or data in this document without prior notice. Elatec declines all responsibility for the use of this product with any other specification but the one mentioned above. Any additional requirement for a specific customer application has to be validated by the customer himself at his own responsibility. Where application information is given, it is only advisory and does not form part of the specification.
Need help?
Do you have a question about the TWN4 MULTITECH NANO M and is the answer not in the manual?
Questions and answers