Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Elatec TWN4 LEPTO M
Summary of Contents for Elatec TWN4 LEPTO M
- Page 1 TWN4 LEPTO M INTEGRATION MANUAL...
-
Page 2: Table Of Contents
TABLE OF CONTENTS INTRODUCTION .................................. 3 ABOUT THIS MANUAL ..............................3 ABOUT TWN4 LEPTO M ..............................3 ELATEC SUPPORT ................................3 REVISION HISTORY ..............................3 SAFETY INFORMATION ..............................4 INTEGRATION INSTRUCTIONS ............................5 GENERAL ..................................5 LIST OF APPLICABLE RULES ............................5 SPECIFIC OPERATIONAL USE CONDITIONS ......................5 LIMITED MODULE PROCEDURES ..........................5... -
Page 3: Introduction
TWN4 Lepto M allows users to read and write almost all common worldwide 125 kHz and 13.56 MHz tags and/or labels. It supports all major transponders from various suppliers like ATMEL, EM, ST, NXP, TI, HID etc. and ISO standards like ISO 14443A/B (T=CL), ISO 15693, ISO 18092 / ECMA-340 (NFC). -
Page 4: Safety Information
• Before installing TWN4 Lepto M into a host device, the integrator should also make sure that he/she has read and understood the ELATEC technical documentation related to TWN4 Lepto M, as well as the technical documentation related to the host device. In... -
Page 5: Integration Instructions
GENERAL TWN4 Lepto M may be installed in any host devices, as long as it is operated under the operational conditions stated in the user manual and other technical documents (e.g. data sheet). TWN4 Lepto M is equipped with two integrated antennas. Thus, no antenna installation is required. -
Page 6: Antennas
ADDITIONAL TESTING, PART 15 SUBPART B DISCLAIMER TWN4 Lepto M is only FCC authorized for the specific rule parts (i.e., FCC transmitter rules) listed on the grant, and the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. -
Page 7: Mechanical Installation
The reader module can be fixed with a corresponding recess in the housing. 3.12 ELECTRICAL CONNECTION The reader module can be connected to the host by USB. 3.13 PROGRAMMATION/SOFTWARE INTEGRATION © 2022 ELATEC GmbH – TWN4 Lepto M integration manual DocRev1 – 09/2022 Page 5 of 11... -
Page 8: Compliance Statements
4 COMPLIANCE STATEMENTS TWN4 Lepto M is in compliance with the EU directives and regulations as listed in the respective EU declaration of conformity. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. -
Page 9: Integrator And Host Requirements
Using a permanently affixed label, TWN4 Lepto M must be labeled with its own FCC and IC identification numbers. In case this label is not visible anymore after integration of TWN4 Lepto M in the host device, it is necessary to bring a label on the host device (on a... -
Page 10: Appendix
Title 47 of the Code of Federal FCC’s rules and regulations Federal Communications Commission Regulations (CFR) For more information about this integration manual or TWN4 Lepto M, contact ELATEC. © 2022 ELATEC GmbH – TWN4 Lepto M integration manual DocRev1 – 09/2022 Page 8 of 11... - Page 11 Elatec reserves the right to change any information or data in this document without prior notice. Elatec declines all responsibility for the use of this product with any other specification but the one mentioned above. Any additional requirement for a specific customer application has to be validated by the customer himself at his own responsibility. Where application information is given, it is only advisory and does not form part of the specification.
Need help?
Do you have a question about the TWN4 LEPTO M and is the answer not in the manual?
Questions and answers