Related Manuals for Mobius MBX BUCKER
Summary of Contents for Mobius MBX BUCKER
- Page 1 USER GUIDE © 2 0 2 0 E T E R O S T E C H N O L O G I E S I N C . A L L R I G H T S R E S E R V E D . M O B I U S T R I M M E R .
-
Page 2: Table Of Contents
SAFETY SAFETY INSTRUCTIONS DISCLAIMER WARNING LABELS SERVICE & REPAIRS GENERAL SAFETY PRECAUTIONS OPERATING CONDITIONS INITIAL SETUP GET TO KNOW YOUR MBX BUCKER WHAT'S IN THE BOX OPERATIONS CONTENTS OPERATION PREP CONTROL PANEL OVERVIEW OPERATION PREP SET-UP & ADJUSTMENTS GENERAL CLEANING... -
Page 3: Safety
MBX BUCKER. We recommend the owner of this equipment develop a standard operating procedure specific to each worksite to address any local hazards or other conditions not outlined in this User Guide. The MBX BUCKER must be inspected regularly for damage, component failure, and wear. Results of inspection activity should be documented. -
Page 4: Warning Labels
A L L R I G H T S R E S E R V E D . M O B I U S T R I M M E R . C O M MOBIUS MBX BUCKER USER GUIDE... -
Page 5: Operating Conditions
If this equipment is used in conditions outside the specified operating conditions, Eteros Technologies cannot guarantee that the built-in safety functions of the Mobius MBX Bucker will function as intended. C O N T E N T S... -
Page 6: Get To Know Your Mbx Bucker
OPERATIONS STAND WELDMENT CASTERS WHAT'S IN THE BOX Your MBX BUCKER comes fully assembled, tested, and ready for operation. When unpacking the device, please ensure the following items are included: • MBX BUCKER MACHINE • USER GUIDE © 2 0 2 0 E T E R O S T E C H N O L O G I E S I N C . -
Page 7: Operation Prep
OPERATION PREP PRIOR TO DEVICE OPERATION, ENSURE ALL GUARDS AND THE Please take the following steps to confirm the MBX BUCKER is ready to operate: FRONT DIE PLATE ARE IN PLACE AND PROPERLY SECURED • Complete a thorough inspection of the equipment to ensure no damage occurred during shipment •... -
Page 8: Set-Up & Adjustments
SET-UP & ADJUSTMENTS MA CH I NE STO P S E QU E N C E The MBX BUCKER typically requires no set-up or adjustments under normal operating conditions. When the machine is in operation, press the stop button. MA CH I NE SHUT DOWN S E Q U E N C E BLADE ADJUSTMENT 1. -
Page 9: General
The machine is designed to be operated on smooth and level floors. If lifting is required, the Mobius MBX Bucker must be lifted using a forklift on the lower structural frame between the casters. Ensure that the forks are fully spread to avoid overturning or flipping off the forks. -
Page 10: Cleaning
The front die plate and rear chipper cover may be removed to facilitate cleaning. The inside of the MBX BUCKER can be washed and wiped as needed. The exterior of the MBX BUCKER should never be hosed or sprayed. Evidence of water near the motor, DO NOT SPRAY conduit, electrical panel, or gearbox could void the machine warranty. -
Page 11: Warranty
Temperature (Ambient) C - 40 Rotor damage is very rare on a MBX BUCKER and is typically the result of rocks, hard metallic objects, or poor setup. Rotor damage resulting from hard objects entering the MBX BUCKER is not covered 80% at 31 under warranty. -
Page 12: Troubleshooting
MATERIAL COMES OUT OF THE CHIPPER UNDER- • see chipper setup on pg 15 PROCESSED OR CHIPPER IS GETTING PLUGGING UP FREQUENTLY MBX BUCKER IS NOT PULLING STOCKS OR • see roller tension/setup on pg 15 BUCKING PROPERLY Eteros Technologies West Eteros Technologies East 202-17665 66A Ave.
Need help?
Do you have a question about the MBX BUCKER and is the answer not in the manual?
Questions and answers