Related Manuals for Lissmac CDM 18 T
Summary of Contents for Lissmac CDM 18 T
- Page 1 CONSTRUCTION TECHNOLOGY OPERATING MANUAL DIAMOND CORE DRILLING MACHINE CDM 18 T LISSMAC Maschinenbau GmbH Lanzstrasse 4 D-88410 Bad Wurzach Telefon +49 (0) 7564 / 307 - 0 Telefax +49 (0) 7564 / 307 - 500 lissmac@lissmac.com www.lissmac.com 1/33...
- Page 2 2/33...
- Page 3 Imprint The operating manual is valid for: Diamond Core Drilling Machines CDM 18 T Company headquarters: LISSMAC Maschinenbau GmbH Lanzstraße 4 D - 88410 Bad Wurzach Tel: +49 (0) 7564 / 307 – 0 Fax: +49 (0) 7564 / 307 – 500 lissmac@lissmac.com...
- Page 4 BASIC SAFETY INSTRUCTIONS Warning notices and symbols in this operating manual The signal word behind the danger symbol indicates the degree of danger: DANGER! This signal word signifies an extremely dangerous situation. If the situation is not avoided, fatal injuries will result.
-
Page 5: Table Of Contents
OPERATING MANUAL This operation manual has been established to make it easier to become familiar with the Preface machine and to utilise its intended application options. This operation manual contains important information on how to operate the machine in a safe, appropriate and economic manner. - Page 6 Notes: 6/33...
-
Page 7: Description Of Performance
1. DESCRIPTION OF PERFORMANCE With their compact, lightweight, ergonomic design, the CDM 18 T provide simple, user-friendly dry drilling every day on the construction site and in buildings. The clamping collar ensures convenient control of the core drill using a clamping handle for hand-guided drilling as well as easy mounting on core drilling stand for guided core drilling. - Page 8 You should particularly handle malfunctions which can compromise safety immediately, or have them addressed by experts. The CDM 18 T is a dry core drill machine and follows the machine classification of a core Appropriate usage drill machine.
- Page 9 For safety-related changes to the machine or its running behaviour, stop the machine immediately and mark it accordingly. Report the problem to the responsible post/person! No changes, removal or addition of parts without the written approval of the manufacturer! The instructions of the tool maker must be followed. Only use tested original replacement parts from the manufacturer! Observe required or prescribed deadlines given in the operating manual for inspection.
- Page 10 1.4. Safety instructions for operation phases 1.4.1. Transport, assembly and installation Transport, assembly and installation on/with the machine may only be carried out if the drive motor is turned off. Transport may only be done, as long as all machine parts are tightened on the machine and individual parts cannot fall.
- Page 11 1.4.3. Operation Refrain from working in any manner that is questionable in regard to safety! Take measures to ensure that the machine is operated only in a safe, functional condition! The machine must be checked at least once per shift for externally identifiable defects or damages! Any changes which occur (including operating behaviour) must be reported immediately to the responsible post/person! If necessary, immediately stop the machine and secure it against restart! Immediately stop and secure the machine in case of malfunctions! Immediately correct malfunctions!
- Page 12 1.4.4. Special work while using the machine Follow all setup, maintenance, and inspection activities and schedules prescribed by the operating manual, including all information about the replacement of parts / assemblies! These activities may only be carried out by technical personnel. Inform operating personnel before beginning special and maintenance work! Name a supervisor! If the machine is turned off during maintenance and repair work, it must be secured against unexpected application of power.
- Page 13 1.5.2. Electric power Use only original fuses with the specified current rating! In case of malfunctions, turn the machine off immediately! Electrical work may only be carried out by technical and qualified personnel. Carry out maintenance or repair work only when the drive motor of the machine is turned off and the tool is not running any more.
- Page 14 1.6. Transport Even when moving only for a short distance, the drive motor of the machine must be turned off. The tool may not be rotating before a restart! When recommissioning, follow the operating manual! 1.7. Packaging and Storage To ensure sufficient protection during shipping and transport, the machine and its components are carefully packaged.
-
Page 15: Description Of Machine
2. DESCRIPTION OF MACHINE 2.1. Name of machine parts Pos. 1 Optical display Pos. 8 Dust collector hose connection Pos. 2 ON / OFF switch Pos. 9 Mounting bracket Pos. 3 Handle Pos. 10 Suction pipe Pos. 4 Connecting cable Pos. - Page 16 2.2. Technical data CDM 18 T Voltage 230 V, 50 Hz Current consumption 8,4 A Rated power 1800 W Output power 1250 W Kind of current einphasig System of protection (Insulation) Class 1 Spindle speed without load 1750 rmp Spindle speed with load...
- Page 17 Regulations state that hearing protection must be worn above a noise level of 85 dB (A), . Wear personal hearing protection The measurements were carried out in corresponding to the norm EN 60745. (Sound pressure) (Sound power) CDM 18 T 92 dB (A) 99 dB (A) 2.5. Hand arm vibration WARNING! Hazard due to vibration Vibrations can lead to bone or joint injuries and to circulation dysfunctions.
-
Page 18: Commissioning
COMMISSIONING 3.1. Connections and operating materials A reliable power source with an operating voltage and corresponding fuses as shown on the model plate Connection of electricity must be available. The automatic phase inverter automatically regulates the direction of rotation. Never operate the machine without the equipped portable residual current device (PRCD). Working with the core drilling machine is like a grinding process in which extremely fine dust is produced. - Page 19 3.3. PRCD-Switch DANGER! Risk of fatal injuries due to a defective PRCD personal protection switch. Severe or fatal injuries from electric shock. An operation of the machine with a broken safety switch PRCD is not permitted! The personal protection switch PRCD must be checked each time before the machine is started ...
- Page 20 3.4. Speed electronics The diamond drilling machine is equipped with specially developed electronics with soft start. It monitors the speed and the red / green indicator lights help to achieve the most favourable work progress and therefore tool bit protecting working conditions. Visual display Green Speed for optimum drilling performance...
- Page 21 ø 200 mm Hand-held max. ø 160 mm Stand Led In the LISSMAC sales booklet, the prices for the tools are determined. This sales booklet can be obtained from the manufacturer at any time. 21/33...
-
Page 22: Transport
3.5.2. Tool installation WARNING! Risk of injury due to hot tools. The tools can get hot if used for a lengthy time. Wear safety gloves when changing the hot tools or allow the tools to cool first. If the core drilling machine is used on a drill stand, the machine must be fixed in the motor collar before the tool is fitted. -
Page 23: Operation
5. OPERATION 5.1. Sicherheit DANGER! Falling drill cores can cause severe injuries! If drilling openings through objects, always check the rooms below or behind and block off the danger zone. Use formwork to secure the drill core against falling. WARNING! Risk of injury due to hot tools. - Page 24 5.2. Hand-held drilling WARNUNG! Risk of injury. Injuries by running tools. When moving the machine the tool must be at a stand still Location changes with the tool rotating are prohibited The ON / OFF switch must not be locked for hand-held held drilling ...
- Page 25 5.3. Switch soft impact feature on and off Only press the soft impact feature ON / OFF changeover switch if the machine is switched off. The core drilling machine is equipped with specially developed electronics with soft start. It monitors the speed and the red / green indicator lights help to achieve the most favourable work progress and therefore tool bit protecting working conditions.
- Page 26 5.4. Remove drill core (blind hole) NOTE! Risk of fracture of the machine cutting segments and/or damage to the drill! Never use the tool to break out the drill core. Use a suitable tool to break out the drill core in the stone ...
- Page 27 6. WARTUNG DANGER! Danger of injury Death or injury from the machine. Maintenance and repair works may only be carried out when the machine is turned off Maintenance and repair works must only be carried out by qualified personnel ...
-
Page 28: Tools
Depending on the application purpose and area, tools are different. To have the best results, the parameters must match. With this diagram, the optimal cutting performance can be determined. In the LISSMAC sales booklet, the prices for the tools are determined. This sales booklet can be obtained from the manufacturer at any time. -
Page 29: Parts List
8. PARTS LIST Art.-Nr. Description Specification Pcs. SUCTION PIPE SWIVEL CPL SPRING CLIP UTPUT SHAFT BULLET 4 DIN5401 CYLINDRICAL PIN 4X18 DIN6325 GROOVED BALL BEARING 6906 2RS LOCK RING J 47X1,75 DIN472 GROOVED BALL BEARING 16005 2RS OIL SEAL 30X47X7 DIN3760 SCHLAGRINGWELLE SCHLAGRING GEHÄUSE SCHR. - Page 30 Art.-Nr. Description Specification Pcs. ELECTRONIC ADJUSTER ADJUSTER HANDLE KPL. HANDLE EXTENSION To prevent incorrect deliveries, when ordering spare parts, indicate the complete model designation, year of manufacture and the machine number! Technical changes may be made! We make it explicitly clear that parts not supplied by us are also not tested and released by us. The installation and use of such products can therefore, in certain conditions, modify your equipment negatively and thus affect safety.
- Page 31 CDM 18 T Stand: 04-2016...
- Page 32 The technical documentation retained by LISSMAC Maschinenbau GmbH, Lanzstrasse 4, D-88410 Bad Wurzach. The CDM 18 T is a dry core drilling machine and follows the machine classification of a core Machine description: drill machine. This machine works in conjunction with a diamond impregnated core drill bit to drill circular holes into stone, concrete and composite materials.
- Page 33 -33-...