Table of Contents
Related Manuals for Lissmac CDR 251
Summary of Contents for Lissmac CDR 251
- Page 1 CONSTRUCTION TECHNOLOGY OPERATING MANUAL CORE DRILLING STAND CDR 251 CDR 501 LISSMAC Maschinenbau GmbH Lanzstrasse 4 D-88410 Bad Wurzach Telephone +49 (0) 7564 / 307- 0 Fax +49 (0) 7564 / 307 - 500 lissmac@lissmac.com www.lissmac.com 1/32...
- Page 2 2/32...
- Page 3 Imprint The operating manual is valid for: LISSMAC- Core drilling stand: CDR 251 CDR 501 Company headquarters: LISSMAC Maschinenbau GmbH Lanzstraße 4 D - 88410 Bad Wurzach Phone: +49 (0) 7564 / 307 – 0 Fax: +49 (0) 7564 / 307 – 500 lissmac@lissmac.com...
- Page 4 BASIC SAFETY INSTRUCTIONS Warning notices and symbols in this operating manual Indicates that failure to comply could lead to severe injury or even death. Danger! Indicates that failure to comply could sometimes lead to injuries. Caution! Note Indicates that failure to comply leads to damage to the machine or other property. Handling information for operators The defined sequence of the handling steps makes proper and safe handling of the machine easier.
- Page 5 Required core drill motor A LISSMAC core drill motor must be installed in the core drilling stand so that the core drilling stand can be operated. The core drill motors can be purchased from the manufacturer.
- Page 6 Notes: 6/32...
-
Page 7: Table Of Contents
1.6. Environmental protection ....................13 1.7. Disposal ..........................13 Machine description ......................14 2.1. Core drilling stand CDR 251 ....................14 2.2. Core drilling stand CDR 501 ....................15 2.3. Technical data ........................16 ... -
Page 8: Table Of Contents Description Of Performance
DESCRIPTION OF PERFORMANCE The CDR 251 and CDR 501 core drill stands are designed as sturdy core drill stands for the powerful daily professional use on the construction site. The CDR series is attractive due to its universal operating options from the left, right, or back of the drilling stand. -
Page 9: Basics Of Intended Use
1.1.4 The LISSMAC Core Drilling Stand is used as a guiding and fastening aid for a LISSMAC Core Drill Motor. A LISSMAC Core Drill Motor with a diamond core bit approved for it must be used for drilling. -
Page 10: Personnel Choice And Personnel Qualification; Basic Responsibilities
1.2.8 Only use original replacement parts from the manufacturer! 1.2.9 Keep intervals for service work which are specified or given in the operating manual! Workshop equipment suitable for the work is absolutely necessary for performing maintenance actions. 1.3. Personnel choice and personnel qualification; basic responsibilities 1.3.1 Only qualified personnel 18 years of age or older may operate the machine independently. -
Page 11: Commissioning
Electrical work may only be carried out by qualified electricians. 1.4.3.8 Only use suitable and tested diamond tools in combination with the LISSMAC Core Drill Motor. 1.4.3.9 For protection before acceleration, move the depth setting slowly into the solid floor. Avoid any contact with the running tool. -
Page 12: Special Work While Using The Machine
1.4.4. Special work while using the machine 1.4.4.1 Follow all setup, maintenance, and inspection activities and schedules prescribed by the operating manual, including all information about the replacement of parts / assemblies! These activities may only be carried out by technical personnel. 1.4.4.2 Inform operating personnel before beginning special and maintenance work! Name a supervisor! 1.4.4.4... -
Page 13: Packaging And Storage
1.5. Packaging and Storage To ensure sufficient protection during shipping and transport, the machine and its components are carefully packaged. When receiving the machine, the machine should be checked for damage. The packaging of the device consists of materials which can be recycled. Put these by type into the relevant recycling containers, so that they can be recycled properly. -
Page 14: Machine Description
MACHINE DESCRIPTION 2.1. Core drilling stand CDR 251 Pos. 1 hand crank Pos. 7 Pillar Pos. 2 UNIVERSAL fitting Pos. 8 Support Pos. 3 Clamping collar 60 mm Pos. 9 Levelling screws, front Pos. 4 Spirit level Pos. 10 Core drilling stand base Pos. -
Page 15: Core Drilling Stand Cdr 501
2.2. Core drilling stand CDR 501 Pos. 1 hand crank Pos. 7 Pillar Pos. 2 UNIVERSAL fitting Pos. 8 Support Pos. 3 Spirit level Pos. 9 Levelling screws, front Pos. 4 Handle Pos. 10 Core drilling stand base Pos. 5 Manual crank feed 1:1 Pos. -
Page 16: Technical Data
2.3. Technical data CDR 251 CDR 501 Core bits -Ø maximum 250 mm 500 mm Adjustable useful length 550 mm 650 mm Motor assembly using UNIVERSAL and 60 mm clamping collar UNIVERSAL Feed 1:1 / manual crank (optional with gearbox 1:1/1:4) Angle drilling 90°... -
Page 17: Commissioning - Assembly And Settings
COMMISSIONING - ASSEMBLY AND SETTINGS 3.1. Securing the core drilling stand For wall or ceiling holes the core drilling stand must never be secured only by drop-in anchors or vacuum Danger! fastening, but always additionally with suitable lifting gear or a quick clamp column, for example. 3.1.1. -
Page 18: Assembly Of The Core Drill Motor
3.2. Assembly of the core drill motor The core drill motor must be disconnected from the power source before installation, cleaning and Danger! servicing! CDR 251 CDR 501 CDR 251 Caution! Caution when installing the core drill motor. There is a danger of crushing! ... -
Page 19: Set Column Incline
3.3. Set column incline Note Lower drill pressure must be selected for inclined holes to prevent the core bit from moving. Release the screwed joints at Pos. 2, Pos. 3 and Pos. 4 on both the left and right ... -
Page 20: Operation
OPERATION The safety instructions of the core drilling stand must absolutely be complied with. Danger! The operating manual of the core drill motor must be observed. Before each operation the core drilling stand must be checked for perfect condition and secure fastening. -
Page 21: Accessories
ACCESSORIES 7.1. Gear unit If necessary an additional gearbox (accessory) with a step-down from 1:4 can be mounted on the right side of the feed carriage. Gearbox mounted on the right side of the feed carriage. 21/32... -
Page 22: Tools
Depending on the application purpose and area, tools are different. To have the best results, the parameters must match. With this diagram, the optimal cutting performance can be determined. Note In the LISSMAC sales booklet, the prices for the tools are determined. This sales booklet can be obtained from the manufacturer at any time. 22/32... -
Page 23: Warranty
WARRANTY The warranty for this machine is 12 months. For the following listed wear parts the warranty only applies if the wear is not caused by operation. Wear parts are parts that with intended use of the machine have limited operational wear. The wear time is not uniformly specified, it differs according to intensity of use. -
Page 24: Spare Parts List Cdr 251
SPARE PARTS LIST CDR 251 Designation Specification 1000 Drill column assembly Drill column Head plate M6x20 DIN7991 Countersunk screw M12x90 Hexagon head screw M12 DIN985 Lock nut 2000 Steel base assembly Steel base Hexagon head screw M12x65 Cap nut 3000... - Page 25 Designation Specification 5000 Feed carriage assembly Base body drive shaft Deep groove ball bearing 6002 2RS SW19 Set screw M8x10 DIN913 Centring screw Eccentric guide pin Fixed guide pin Track roller without bearing Deep groove ball bearing 6001 2RS Lock nut M8 DIN982 Adjustment bolt M10x1 GN817-5-5 CK...
- Page 26 26/32 CDR 251 01-2017...
-
Page 27: Spare Parts List Cdr 501
SPARE PARTS LIST CDR 501 Designation Specification 1000 Drill column assembly Pillar Clamping block, left Hexagon socket head screws M8 x12 Support M12 DIN 934 Hexagon head screw M12x100 block Hexagon socket head screws M8x16 Countersunk screw M6x12 DIN 7991 Head plate Handle Retaining plate... -
Page 28: Accessories Cdr 501
Designation Specification 5000 Feed carriage assembly Feed carriage Countersunk screws M5x12 DIN 7991 Stop plate Adjustment bolt M10x1 GN817-5-5 CK Lock nut M12 DIN 982 Washer Ø13 DIN 125 Feed shaft Grooved bearings 6002 2 RS Set screw M8x10 DIN 913 SW19 Locking ring Ø15 DIN 471... - Page 29 The LISSMAC Core Drilling Stand is used as a guiding and fastening aid for a LISSMAC Core Description of the Drill Motor. A LISSMAC Core Drill Motor with a diamond core bit approved for it must be used machine for drilling.
- Page 30 Designation Specification 4500 Turning lever assembly (Accessories) Push button GN719.1 - 33 - B12 Crank rod 290mm Pressure piece GN614-6 DU Aligning pin Ø6x30 DIN7 Crank pin 8000 Wheel assembly Axis Wheel 125x38/NL50/15 Disk ø15 DIN 125 Splint ø 4 x 30 DIN 94 Hexagon head screw M12x40 DIN 931 Setting panel...
- Page 31 30/32 CDR 501 01-2017...
- Page 32 32/32...