BC Biomedical SonoSite ULT-2000 Series Quick Start Manual

Ultrasound probe leakage testing
Hide thumbs Also See for SonoSite ULT-2000 Series:

Advertisement

SonoSite Ultrasound Probe Leakage Testing with the BC Biomedical ULT-2000 Series
Quick Start Guide
Install the SonoSite Probe Connector on the compatible BC Biomedical Probe Adapter ULT-PA-32 (pictured above). Align the SonoSite Probe
Connector with the Probe Adapter and gently insert the connector into the adapter. Turn the latch counterclockwise to engage the connector
then fold the latch against the connector to lock it into place. Refer to the chart on the following page to cross reference your SonoSite Probe
with the compatible BC Biomedical Probe Adapter(s).
Page 1 of 5
ULT-2000 Series Quick Start Guide (SonoSite Ultrasound) – 10/2019

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SonoSite ULT-2000 Series and is the answer not in the manual?

Questions and answers

Summary of Contents for BC Biomedical SonoSite ULT-2000 Series

  • Page 1 Quick Start Guide Install the SonoSite Probe Connector on the compatible BC Biomedical Probe Adapter ULT-PA-32 (pictured above). Align the SonoSite Probe Connector with the Probe Adapter and gently insert the connector into the adapter. Turn the latch counterclockwise to engage the connector then fold the latch against the connector to lock it into place.
  • Page 2 SonoSite Ultrasound BC Biomedical Adapter ULT-AC-10 Probe Ultrasound ULT-PA-11 ULT-PA-32 (Fork Adapter) Model System(s) Also Required? ✓ TEExi MTurbo & Edge II TEExp X-Porte ✓ Refer to the chart above to determine if the ULT-AC-10 Fork Adapter is also required to test your SonoSite Probe. If the ULT-AC-10 Fork Adapter is required, gently insert it between the two deflection control wheels until it firmly clips onto the metal center shaft of the control wheels.
  • Page 3 ULT-SP-20 Splitter is only required if using the ULT-AC-10 Coil Cable from BC Biomedical Fork Adapter. If the Fork Probe Adapter Adapter is not used, the Probe Adapter cable may connect directly to the Ultrasound Leakage Tester. BC Biomedical, ULT-2000 Series...
  • Page 4 *If using an automated TEE Probe Disinfector see Appendices for details. BC Biomedical, ULT-PC-10 Conductivity Probe Soak Tray Setup BC Biomedical, ULT-PC-30 or ULT-PC-31 Submersible Conductivity Probe SonoSite Probe submerged between 60cm and 90cm as indicated on the probe shaft.
  • Page 5 Example Soak Tube Test Setup To Perform a SonoSite Ultrasound Probe Leakage Test with the ULT-2000 Series 1. Verify that the ULT-2000 Series is set to test a SonoSite Ultrasound Probe, as indicated by the Device Configuration screen above. o The Device Configuration Screen appears briefly as the ULT-2000 Series is powered on.
  • Page 6 Appendix A CS Medical TD 100 Details Using a TD 100 to high-level disinfectant your TEE probe, perform electrical leakage testing inside the TD 100: Press START on the TD 100 to initiate a disinfection cycle and insert your TEE probe. Insert the tip of the ULT-PC-31 Submersible Conductivity Probe until the white mark is at the reservoir.

Table of Contents