Related Manuals for Axminster AW150BG
Summary of Contents for Axminster AW150BG
- Page 1 AW150BG Code 107682 AW200BG Code 107684 Original Instructions AW150BG, AW200BG Bench Grinders AW150BG AW200BG AT: 09/02/2022 BOOK VERSION: 5...
-
Page 2: Eu Declaration Of Conformity
Wiring Diagram Notes 17-18-19 EU Declaration of Conformity Cert No: RBG625A, RBG825A EU Declaration of Conformity This machine complies with the following directives: Axminster Tool Centre Ltd Axminster Devon EX13 5PH UK 2006/42/EC EN 61000-3-3: 2013+A1: 2019 axminstertools.com 2014/30EU EN 55014-2: 2015... -
Page 3: What's Included
What’s Included Quantity Item Part Model Number Quantity Item Part Model Number AW150BG AW200BG 150mm Grinder 200mm Grinder Quantity Item Part Tool rest brackets Butterfly knobs & washers Eye shields Eye shield arms Long bolts & washers Instruction manual Magnifying glass... -
Page 4: General Instructions For 230V Machines
General Instructions for 230V Machines • Leave machine unplugged until work is about to The following will enable you to observe good working practices, keep yourself and fellow workers safe and commence. maintain your tools and equipment in good working order. •... - Page 5 Specific Safety Precautions for Grinding Machines 11. Hot sparks are a hazard! Never carry out grinding 16. Avoid awkward hand positions where a sudden slip operations near flammable gas or liquid. could cause the hands to come into contact with a grinding wheel, wire brush etc.
- Page 6 Assembly Step 3 Step 4 Threaded hole Gears Remove the clamping knobs (A) from the eye shields (E). Locate Locate the two long bolts (G), place a spring/washer over the the eye shield arms (F) and mess the two gears together. bolts.
-
Page 7: Illustration And Parts Description
Illustration and Parts Description Light bulb housings Air vents AW150BG Motor Light bulb Eye shield guard with integrated magnifying glass Grinding stone Tool rest butterfly clamping knob Housing slot for bolting the grinder Storage draw to the work bench Eye shield guard... -
Page 8: Specification
Specification Code 107682 Code 107684 Model AW150BG Model AW200BG Rating Workshop Rating Workshop Power 250W 230V 50Hz 1Ph Power 550W 230V 50Hz 1Ph Duty Cycle S1 150W Duty Cycle S1 370W Speed 2,980 rpm Speed 2,980 rpm Wheel Diameter 150 mm... - Page 9 Setting Up the Grinder Carry out final checks e.g. check the gap between the tool rest and the stone is correct, check the stone is not badly CONNECT THE GRINDER TO THE deformed (rounded edges, grooved face, etc; unless you MAINS SUPPLY.
- Page 10 Changing the Grinding Stone/Dressing the Stone Step 4 CONNECT THE GRINDER TO THE MAINS SUPPLY. Reconnect the grinder to the mains supply, give the grinder a ‘short burst’ , by switching it on and off quickly. Check the grinder is not subject to any undue vibration. If the grinder does vibrate, switch off immediately and disconnect from the main supply.
- Page 11 Dressing the Stone/Changing the Light Bulbs Changing the Light Bulb Code 410057 To replace a blown light bulb, follow the instruction below. Step 1 Phillips screw Diamond Dressing Block useful for dressing across the width of the grinding wheels or to produce flatter surfaces than single point dressers.
- Page 12 Exploded Diagrams/Lists AW150BG Bench Grinder 27.07.2020...
- Page 13 Exploded Diagrams/Lists Description Specification Cord clip Philips screw M4 x 8 Wire with plug Hex nut Cord Clip Plate Left wheel cover Philips screw+spring M4 x 8 washer+flat washer Type I hex nut M12 left Hex nut Wheel Flange Switch board Grinding wheel (WA 150x20xφ12.7mm 80#)
- Page 14 Exploded Diagrams/Lists AW200BG Bench Grinder 27.07.2020...
- Page 15 Exploded Diagrams/Lists Descriptions Specification Spring washer Philips screw M4 x 8 Hex nut Sleeve Swith plate Left wheel guard cover Swith I type hex nut Flat washer Whee flange Tooth lock wash Left wheel WA 80# 200x25x15.88mm Motor housing Philips screw M5 x 10 Cord sleeve Spring washer...
-
Page 16: Wiring Diagram
Wiring Diagram... - Page 17 Notes...
- Page 18 Notes...
- Page 19 Notes...
- Page 20 The packaging is suitable for recycling. Please dispose of it in a responsible manner. EU Countries Only Do not dispose of electric tools together with household waste material. By law they must be collected and recycled separately. Axminster Tools, Axminster Devon EX13 5PH axminstertools.com...