BN Products BNCE-30-24V Operation & Instruction Manual
Hide thumbs
Also See for BNCE-30-24V:
- Operation & instruction manual (16 pages) ,
- Operation manual (12 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for BN Products BNCE-30-24V
Summary of Contents for BN Products BNCE-30-24V
- Page 1 Operation & Instruction Manual Model BNCE-30-24V SN# ___________ Keep this booklet and enter your tool serial number in the appropriate space above. 3 4 50 Sabin Bro w n Ro ad • W icke n bu rg, AZ 8 53 9 0 ( 8 0 0 ) 9 9 2 -3 8 3 3 •...
-
Page 2: Specification
Instruction Manual Please read this m anual before operating this tool. Co n te n ts Ge n e ral Safe ty Ru le s W o rk Are a Safe ty Ele ctrical Safe ty Se rvice Fu n ctio n s an d Ap p licatio n s Specification Stan d ard Blad e : Op e ratio n... -
Page 3: Work Area Safety
Ge n e ral Safe ty Ru le s Warning! Read and understand all instructions. Failure to follow all instructions listed below may result in electric shock, fire and/or serious personal injury. PLEASE SAVE TH ESE IN STRU CTION S! W o rk Are a Safe ty •... - Page 4 ensure these are connected and properly used. Use of dust collection can reduce dust- related hazards. Keep fingers and body parts away from the blade opening. • Po w e r To o l U s e an d Care •...
- Page 5 Ap p licatio n o f th e To o l - Actual areas of application the Cutting Edge Saw is used for are as follows: The BNCE-30-24V can cut up to 1” grade 60 rebar (reinforcing bars, up to 3/5” I.D pipe, 1” O.D. copper water pipe, 1” O.D. tubing, 3/4” EMT conduit, 1” square steel tubing and bar, up to 1”water pipe sch40 and schedule 80, up to 1-1/8”...
-
Page 6: Main Te N An Ce O F Th E Main U N It
Op e ratio n In s tru ctio n s Locate the front handle in the m ounting hole that provides the best grip. To operate the trigger, depress the trigger and slide forward to start the saw. Start the saw before cutting and then apply a light pressure m oving forward through the cut. -
Page 7: Important Safety Instructions
It is also recom m ended that the cutting blade be rem oved and inspected for any m ateri- als that did not exit out the chip exhaust area. This should be done after 4-8 hours of use. Most m aterial cutting chips would norm ally exit out the chip exhaust area and into the Cutting Chip Catch Bag. - Page 8 • Do not operate charger with dam aged cord or plug. If the cord or plug is dam aged, ask BN Products-USA authorized service center to replace it in order to avoid a hazard. • Do not operate or disassem ble charger if it has received a sharp blow, been dropped, or otherwise damaged in any way;...
-
Page 9: Po W E R Gau Ge
Po w e r Gau ge If you press the switch on the bottom of the power tool to check the battery status, the LED light will turn off after a few seconds. Check the battery level as follows. Page | 9... -
Page 10: In S Tallin G An D Re M O Vin G Batte Ry
In s tallin g an d re m o vin g batte ry Do not use force when inserting the battery. To insert the battery, align the tongue on the battery with the groove in the housing and slip into place. Always insert it all the way until it locks in place with a little click. - Page 11 • Low tem perature: Let stand at room tem perature until norm al tem perature occures. If Checking does not solve the problem , please contact BN Products-USA, LLC or an au- thorized service center nearest you. Page | 11...
- Page 12 Page | 12...
- Page 13 Page | 13...
- Page 14 Parts List for BNCE-30-24V Note Description Part No. BNCEP1-71 HEXAGON SOCKET SCREW (M5X14) Part BNCEP30-02 BOTTOM PLATE GUARD (BNCE-30) Part BNCEP1-73 HEXAGON SOCKET SCREW (M5X8) Part RB-BNCE-30 BLADE, REPLACEMENT (BNCE-30) Part BNCEP1-75 BLADE FLANGE AND SPINDLE Part BNCEP-07 HEX BOLT (M5X30)
- Page 15 Parts List for BNCE-30-24V Note Description Part No. BNCEP-33 BLADE LOCKING BUTTONS Part BNCEP24V-34 SCREW TAPPING PAN HEAD T15 TOR 4 Part BNCEP24V-35 Part BNCEP24V-36 BEVEL PINION Part BNCEP24V-37 BALL BEARING 608-2RS Part BNCEP24V-38 DIAPHRAGM Part BNCEP24V-30A ROTOR ASSY Assy...
- Page 16 Lithium -Ion 24V Battery (2) With Charger Rem ovable Side Handle (Three Positions) Blade Spindle Locking Button Safety Trigger Switch Cutting Slot Opening And Blade Adjustable Slot Chip Exhaust Port (shown without For Cutting attachable Cutting Chip Catch Bag) Special Tungston Carbide Tipped Cutting Blades Flush Cutting Bottom Plate Model No.
Need help?
Do you have a question about the BNCE-30-24V and is the answer not in the manual?
Questions and answers