SERVICE MANUAL Ver. 1.1 2005. 02 • The MDR-IF4000 is the cordless stereo headphones that comprises the MDR- DS4000. • MDR-DS4000 consists of the following models respectively. Cordless stereo headphone MDR-IF4000 Digital surround processor DP-IF4000 General Modulation System Secondary carrier wave frequency...
IC pins, etc. • Usable with ordinary solder It is best to use only unleaded solder but unleaded solder may also be added to ordinary solder. • Repaier DP-IF4000 with MDR-IF4000. TABLE OF CONTENTS Specifications ... 1 GENERAL ...
6 VOL (Volume) control Use to adjust the volume. 7 Ear pad (right) 8 POWER indicator By pulling up the self-adjusting band, the indicator lights red when battery power is sufficient. MDR-IF4000 This section is extracted from instruction manual.
MDR-IF4000 • This set can be disassembled in the order shown below. 2-1. DISASSEMBLY FLOW 2-2. FRONT PLATE (R) ASSY (Page 4) 2-3. RX BOARD (Page 5) 2-4. HANGER (R) (Page 5) 2-5. WIRING ON THE RIGHT SIDE (Page 6) Note: Follow the disassembly procedure in the numerical order given.
BATT board and driver (L-CH) natural 3 RX board to driver (R-CH) natural hanger lid (R) Pay attention to the leads when assembling. projection MDR-IF4000 cushion (B) to PD2 board to BATT board and driver (L-CH) natural 5 hanger (R)
MDR-IF4000 2-5. WIRING ON THE RIGHT SIDE 2-6. FRONT PLATE (L) ASSY housing (L) assy 5 front plate (R) assy 3 screw (P 2.6x6) RD1 board (R-CH front) RD2 board (R-CH rear) 4 Removal the solder at 2 places. Note for installation : Solder the leads at the...
4 BATT board natural 2 two screws (P 2.6x6) hanger lid (L) Pay attention to the leads when assembling. projection MDR-IF4000 places shown below with attention to their colors. natural to RX board to SW board to driver (L-CH) 5 hanger (L)
MDR-IF4000 2-9. WIRING ON THE LEFT SIDE RD2 board (L-CH front) RD1 board (L-CH rear) 2-10. HANGER LID (L) 1 screw (P2.6 x 6) 2 screw (P2.6 x 6) 3 head band hanger lid (L)
2-12. HOW TO HANG THE TENSION SPRING suspender assy housing (L) assy head band cushion (B) Note for installation : Insert the end of the hanger lid (L) tension spring suspender assy MDR-IF4000 suspender assy under the S701 on SW board. SW board S701...
MDR-IF4000 NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. For schematic diagrams. Note: • All capacitors are in µF unless otherwise noted. (p: pF) 50 WV or less are not indicated except for electrolytics and tantalums. • All resistors are in Ω and W or less unless otherwise specified.
Page 23
MDR-IF4000 US Model Canadian Model SERVICE MANUAL AEP Model E Model Ver. 1.1 SUPPLEMENT - 1 File this Supplement with the Service Manual. Subject : SUFFIX CHANGE OF RX BOARD 9-879-301-81...
Page 24
MDR-IF4000 • CHANGE OF RX BOARD The RX board was changed into suffix-12. Printed wiring board and schematic diagram of new type, and changed parts list are described in this Supplement-1. Refer to original service manual (9-879-301-02) previously issued for the other information.
Page 25
PRINTED WIRING BOARD – RECEIVER SECTION – Suffix-12 RX BOARD ( SIDE A ) RV201 POWER MDR-IF4000 : Uses unleaded solder. RX BOARD ( SIDE B ) BATT BOARD ( Page 13 ) ( NAT ) ( RED ) C301...
Page 27
8-719-988-61 DIODE 1SS355TE-17 6.3V D104 8-719-988-61 DIODE 1SS355TE-17 D502 8-719-059-98 DIODE SLR-342VC3F (POWER) MDR-IF4000 RX: Suffix-12 The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. When indicating parts by reference number, please include the board.
Page 28
MDR-IF4000 RX: Suffix-12 Ref. No. Part No. Description < IC > IC001 8-753-208-23 IC CXA3668N-T4 IC101 8-752-425-06 IC CXD4017R IC102 6-707-193-01 IC BU4223G-TR IC201 6-707-192-01 IC PCM1773PWR IC301 8-759-347-33 IC NJM2113V-TE2 IC302 8-759-347-33 IC NJM2113V-TE2 IC501 6-701-851-01 IC XC62HR1502MR < COIL >...
MDR-IF4000 REVISION HISTORY Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper right on the revised page allows you to jump to the next revised page. Ver. Date 2004.11 2005.02 Addition of US, Canadian and AEP models.