F&F DRM-02 Quick Start Manual

Konstantynowska 79/81 95-200 Pabianice
phone/fax: (+48 42) 215 23 83 / 227 09 71 POLAND
http://www.fif.com.pl e-mail: fif@fif.com.pl
MICROWAVE MOTION DETECTOR
WARRANTY. The F&F products are
covered by a warranty of the 24 months
from the date of purchase. Effective only
with proof of purchase. Contact your
dealeror directly with us. More
information how to make a compliant can
be found on the website:
5 9 0 8 3 1 2
www.fif.com.pl/reklamacje
Do not dispose of this device to a garbage bin with other unsorted waste!
In accordance with the Waste Electrical and Electronic Equipment Act
any household electro-waste can be turned in free of charge and in any
quantity to a collection point established for this purpose, as well as to the
store in the event of purchasing new equipment (as per the old for new rule,
regardless of brand). Electro-waste thrown in the garbage bin or abandoned
in the bosom of nature pose a threat to the environment and human health.
Purpose
The motion detector is used for automatic, temporary lighting attach
if a person or another object appears in detector's range in places such
as hallways, courtyards, approaches and driveways, garages, etc.
Microwave sensor allows for motion detection by wooden boards,
plasterboard panels, glass and plastics.
Functioning
DRM sensor emits and bounces high-frequency 5.8 GHz electromagnetic
waves. The sensor detects changes in the reflected waves caused
by movement of the object in the area of detection. The sensor detects
movement of an object to and from the sensor. Movement in the range
of detection will automatically attach the lighting for time set by the user.
After this time the lights will be turned off automatically. The motion sensor
is equipped with light dependant relay able to attaching lighting during
the day. Detection status and standby to attach lights are activated only after
dusk. Sensor activation time might be adjust by the user.
- 1 -
Technical data
supply
current load
frequency of the microwaves radiation
power radiation
detection range
detection ray - adjustable (for h=2,5m)
activation treshold - adjustable
receiver's activation time - adjustable
activation delay
power consumption
connection
working temperature
dimensions
fixed two screws to the substrate
protection level
Assembly
1. Unscrew the outer shield of the detector. Unscrew the two screws and
remove the sensor cover (Pict. 1).
2. Disconnect the power.
3. Wires provide throughout eyelet rubber in mounting base of the sensor.
4. Basis with two screws attached to the substrate.
5. Connect according to schema.
6. Set area of detection, set the sensitivity of the light dependant relay and
activation time.
7. Assemble the sensor's cover housing (Pict. 3).
Wiring diagram
L
DRM
L'
N
- 3 -
In addition, there is a possibility of adjustment of the detection area in range
F&F Filipowski sp. j.
3-10 m (for h= 2.5 m) and the receiver actuation time adjustment
to 8 s ÷ 12 min. The inclusion of the receiver is signaled by a shining green LED.
Sensor can work indoors. The sensor allows for motion detection by wooden
boards, plasterboard panels, glass and plastics. Temperature changes do not
DRM-02
affect on motion detection
ATTENTION!
The power of microwave radiation is relatively low and is completely safe for
humans and animals. Its value is less than 10 mW. By comparison,
microwaves and cell phones radiate about 1000mW of power (100 times
harder).
5 9 3 9 6 6
Settings
Detection range
?
Actuation time
Sensitivity of light dependant relay
Device assembly
230V AC
<5A
5,8GHz
<10mW
360°
1÷10m
2÷2000Lx
8s÷12min.
1s
0,9W
screw terminals 1mm ²
-25÷50°C
Ø103 h= 42mm
IP40
(Pict. 2).
L
N
D150629
Radius of the sensor detection can be adjusted in the range from
R
2 m to 10 m (the parameters for the sensor mounted at a height
of 2.5 m). Rotate the knob to the right [max] increases the area of
a field of detection, rotate left [min] reduces the area of the field
detection.
Receiver's actuation time can be adjusted between 8 s for 12 min.
Rotate knob to the right [max] increases ON time, rotate left [min]
reduces the attached time. After a set time receiver is turned off
automatically.
Sensitivity of light dependant relay can be adjusted in
range from 2 Lx to 2000 Lx. Rotate the knob toward to the „moon"
sign - attached later, rotation to the „sun" sign - attached earlier.
In order to sensor was active throughout the day, set the knob
maximally toward the „sun".
- 2 -
Pict. 1
Pict. 2
- 4 -
Pict. 3