Roger Technology H70/200AC Quick Start Manual
Hide thumbs
Also See for H70/200AC:
- Instruction and warnings for the installer (172 pages) ,
- Instructions and recomendations for the installer (60 pages) ,
- Instruction and warnings for the installer (41 pages)
Table of Contents
Advertisement
Quick Links
H70/200AC is a range of 230V AC controllers and controls automations for gates with 1 or 2 asynchronous single phase ROGER
motors.
1. Typical installation
2
A
Power supply H70/200AC - Motors
1
Photocell - Receiver
2
Photocell - Transmitter
3
Flashing lamp unit
4
Antenna
5
Selector / Keypad
Quick Start H70/200AC
4
3
5
1
A
3x1,5 mm
4x0,5 mm
2x0,5 mm
2x1 mm
2
RG58 50 Ohm cable for external use (max.10 m)
Cavo 3x0,5 mm
1
double insulated cable (max.15 m) - 3x2,5 mm
2
double insulated cable (max.20 m)
2
double insulated cable (max.20 m)
2
double insulated cable (max.10 m)
cable (max.20 m)
2
Via S. Botticelli 8 • 31021 Bonisiolo di Mogliano Veneto (TV) • ITALIA
P.IVA 01612340263 • Tel. +39 041.5937023 • Fax. +39 041.5937024
info@rogertechnology.com • www.rogertechnology.com
EN
Rev01 20/08/2020
2
A
(max. 30 m)
2
ROGER TECHNOLOGY
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Roger Technology H70/200AC
Summary of Contents for Roger Technology H70/200AC
- Page 1 Quick Start H70/200AC Rev01 20/08/2020 H70/200AC is a range of 230V AC controllers and controls automations for gates with 1 or 2 asynchronous single phase ROGER motors. 1. Typical installation Power supply H70/200AC - Motors 3x1,5 mm double insulated cable (max.15 m) - 3x2,5 mm (max.
- Page 2 2. Electrical connections RECOMMENDED USE for Series F2ES - F2S photocells 1 2 3 4 5 Accessories illustrated are indicative only 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 FUSE F630mA PROG TEST F630mA...
- Page 3 4. Before starting ... a) Select the automation system model installed with the parameter A1. Standard motor (4-pole) - (MONOS4/200 and all existing codes with the exception of the following codes for the value A1 01) Slow motor (6pole) - (R20/302, R20/502, R21/368, H23/282, R41/832, R41/833) 1 MOTOR 2 MOTORS b) Select the number of motors installed with the parameter 70.
- Page 4 5. Acquisition procedure (with encoder enabled, with or without limit switches - 75 01) 1. Press and hold PROG for 4 seconds. 2. APP- appears on the display. 3. Press PROG. 4. AUTO appears on the display. 5. MOTOR 1 starts opening at low speed. 6.
- Page 5 Acquisition procedure (without encoder, only for opening limit switch) 1. Press and hold PROG for 4 seconds. 2. APP- appears on the display. 3. Press PROG. 4. MOTOR 1 starts opening at normal speed. 5. AP1 is shown on the display. 6.
- Page 6 6. Setting basic parameters Position control Position control MOTOR 1 MOTOR 1 deceleration space MOTOR 1 deceleration space MOTOR 2 deceleration space Opening delay of MOTOR 1 Initial acceleration MOTOR 2 Position control when opening Initial acceleration when opening Initial acceleration when closing Opening delay of MOTOR 2...
Need help?
Do you have a question about the H70/200AC and is the answer not in the manual?
Questions and answers