1. Manuals
  2. Brands
  3. ISLABIKES Manuals
  4. Bicycle
  5. eJoni
  6. Owner's manual

ISLABIKES eJoni Owner's Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
eJoni
Owner's manual
www.islabikes.co.uk

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the eJoni and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for ISLABIKES eJoni

Summary of Contents for ISLABIKES eJoni

  • Page 1 Owner’s manual www.islabikes.co.uk...
  • Page 2 Setting up your eJoni The Bicycle Brake pads 13. Frame Saddle 14. Fork Seatpost 15. Cranks Seatpost clamp 16. Pedals Saddle clamp 17. Rear light Stem bolts 18. Front light 19. Charging point Spokes 20. Motor Tyres 21. Motor cable (Non driveside Chainstay) 10.
  • Page 3 24. iWoc TRIO controller 28. Stem bolt 25. Brake levers 29. Handlebars 26. Stem 30. Gear shifters 27. Headset www.islabikes.co.uk...
  • Page 4 The iWoc Controller Up Button Short Press: Increase Assist Long Press: Lights On/Off Indicator LED First Colour: Assist Level Second Colour: Battery Level Middle Button Long Press: On/Off Down Button Short Press: Decrease assist Long Press: Walk mode eJoni...
  • Page 5 Step 1 of 13 Remove front wheel and fork packaging Remove front wheel Remove fork protector. protection packaging. DO NOT PULL BRAKE when caliper spacer is removed. Please keep caliper spacer for transportation when wheel is removed. Remove brake caliper spacer www.islabikes.co.uk...
  • Page 6 Install quick release and secure front wheel in fork Install front quick release (QR) skewer from pedal box. Ensure QR skewer springs orientation is correct . Correct Incorrect 2. Put front wheel into the fork. Ensure (QR) lever is not on gear side. eJoni...
  • Page 7 Secondly, push and pull the wheel from side to side. If there is no movement from either of these actions the wheel is installed correctly. www.islabikes.co.uk...

  • Page 8: Handlebar Set Up

    3.3. Check the stem is tight by standing at the front of the bike with the wheel clamped between your legs. While holding the grips, gently try to turn the handlebars. The handlebars should not move independently to the wheel. eJoni...
  • Page 9 If it is possible to rotate the headset spacer, then continue to 3.6. If you cannot rotate a headset spacer, proceed to step 5 of 13. www.islabikes.co.uk...
  • Page 10 90° clockwise to remove the play. Re-tighten the two stem clamp bolts. Restart the process from step 3.3. If in doubt, please consult our technical support team on +44 (0) 1584 708 383 or email techsupport@islabikes.co.uk eJoni...
  • Page 11 Failure to correctly tighten stem clamp bolt may result in serious injury or death. If in doubt, please consult our technical support team on +44 (0) 1584 708 383 or email techsupport@islabikes.co.uk. Before riding check front brake operation is correct. To check this, apply both the front and rear brake, they should feel the same.

  • Page 12: Handlebar Height Adjustment

    Arrange the handlebar stem and spacers to achieve the desired handlebar height. Warning - spacers cannot be added or removed from this assembly. The original quantity needs to remain. Stem bolt Headset spacer Headset spacer Stem bolt Headset bearing cover eJoni...
  • Page 13 (5.) start the process again. WARNING: Failure to correctly adjust the handlebar height may result in serious injury or death. If in doubt, please consult our technical support team on +44 (0) 1584 708 383 or email techsupport@islabikes.co.uk. www.islabikes.co.uk...

  • Page 14: Pedal Installation

    LH pedal has line marking on axle. If these features are missing, another tip is to check the Islabikes logo. When standing at the back of the bike looking towards the front, the Islabikes text on the pedal should be in the correct orientation to read:...

  • Page 15: Adjust Saddle Height

    Saddle height is very much a personal preference amongst adult cyclists. If you are unsure of the most appropriate saddle height for you then we would be delighted to help. You can contact our technical support team on +44 (0) 1584 708 383 or email techsupport@islabikes.co.uk. www.islabikes.co.uk...
  • Page 16 This app will allow you to use the following features available on your ebike: Cycle Computer Dashboard Use your phone as a display for your eJoni to show real-time speed, distance covered, assist level, remaining battery life and power consumption.
  • Page 17 4. Open the app and follow the prompts to setup a new ebikemotion user account. Please ensure that you read through the Privacy Notice shown during the setup process and only accept if you are happy with the terms of the agreement. www.islabikes.co.uk...

  • Page 18: Charging The Battery

    Both the connector and the charging point have arrows moulded into them to show the correct alignment. Failure to correctly align the arrows may damage the pins in the connector and prevent you from being able to charge the bike. eJoni...
  • Page 19 The battery charger is suitable for indoor use only. Never attempt to tamper with either the charging plug or connector. Always re-fit the charging port cap once the bike is charged. Never attempt to remove the battery from the downtube of your eJoni. www.islabikes.co.uk...
  • Page 20 Turning the bikes electrical system on and off Your new eJoni will not provide any form of assistance unless the electronic portion of the bike is switched on. This not only acts as a safety feature but also makes it possible for you to use the bicycle normally should you run out of battery charge.
  • Page 21 4. Press the ‘link my SmartBike’ button at the bottom of the screen. If you have multiple eJoni’s, the app will give you a list of available bikes to choose from. 5. Once successfully paired, a notification banner will appear at the top of the screen and the iWoc Trio remote will flash blue.
  • Page 22 Step 11 of 13 Changing the level of motor assistance Your Islabikes eJoni’s EPAC is equipped with four levels of motor assistance: Level 0 (White Light) = No Assist Level 1 (Green Light) = Low Assist Level 2 (Orange Light) = Moderate Assist...
  • Page 23 Each slider corresponds with levels 1, 2 and 3 on the iWoc Trio controller. Remember to click ‘Save Configuration’ when you are ready to save the changes to the bicycle. www.islabikes.co.uk...

  • Page 24: Walk Mode

    Step 12 of 13 Walk mode 1. Press and hold button until the LED flashes white. The bicycle will advance at a constant 5km/h as long as the button is depressed. Long Press: Walk Mode eJoni...
  • Page 25 Important: Do not lock up the wheels at any point during the bed-in procedure. Allow the brakes to cool prior to any additional riding. If you require further information about your brakes, contact our technical support team on +44 (0) 1584 708 383 or email techsupport@islabikes.co.uk. www.islabikes.co.uk...
  • Page 26 Handlebar ends can become exposed from repeated contact with the ground or heavy fall. Never ride a bike with an unplugged handlebar end. You can buy replacement handlebar grips on our website www.islabikes.co.uk or call +44 (0) 1584 708 383. eJoni...
  • Page 27 Safety first Your eJoni weighs approximately 14Kg with no rider or luggage. Your eJoni has been designed to be ridden on paved roads for means of transportation or leisure where the tyres remain in contact with the ground. The maximum safe combined rider and luggage weight limits are as follows: •...

  • Page 28: Usage Guidelines

    If in any doubt, please contact our technical support team on +44 (0) 1584 708 383 or email techsupport@islabikes.co.uk. Or take it to a qualified cycle mechanic for inspection. Never use your eJoni as a method of towing any other person, vehicle or object. eJoni...

  • Page 29: Rear Wheel Removal

    Rear wheel removal Your eJoni bicycle uses a rear hub motor which consequently requires a slightly different procedure for removing the rear wheel: Ensure that the electronic system is switched off via the iWoc Trio controller. You must always disconnect the motor cable before doing any maintenance or servicing work on the rear of the bicycle.

  • Page 30: Refitting The Rear Wheel

    3. Line up outer sprocket from the cassette with the chain and push the axle up into the dropouts. 4. Align shaped washers correctly and torque up wheel nuts to 35Nm. eJoni...
  • Page 31 Re-attach the motor cable. You must ensure that the orientation arrows on the plug and socket are aligned whilst doing this to ensure that the cable is not damaged. www.islabikes.co.uk...
  • Page 32 7. Re-attach the cable guide clips. You must complete this final step in order to prevent the cable from getting trapped in the rear wheel. Failure to do so may result in serious injury or even, in severe circumstances, death. eJoni...

  • Page 33: Troubleshooting

    Check the plug connection at the wall. Check the connection to the charging port on your bike. If the bike still does not begin to charge, please contact Islabikes. 5. If the motor assist does not work: Check the PAS sensor (on the drive side of the rear hub) is in position.
  • Page 34 There is an error in the system. Connect your smartphone by Bluetooth to see a detailed description of the error. Alternatively contact Islabikes for assistance. Please note that if the issue is serious enough it could stop the motor from working.
  • Page 35 Using the SmartBike web dashboard The SmartBike web dashboard also provides you with the opportunity to get more from the technology inside your eJoni bicycle. To access the dashboard, follow these steps: 1. Log onto Islabikes.my-smartbike.com. 2. Enter the username and password that you chose when setting up the My SmartBike smart device app for the first time.
  • Page 36 Discontinue use immediately if anything untoward is spotted and contact our technical support team on +44 (0) 1584 708 383 or email techsupport@islabikes.co.uk. eJoni...
  • Page 37 Storage In order to safely store and maintain your eJoni bike, please observe the following instructions: Do not store or leave your eJoni in direct sunlight for prolonged periods of time. Do not leave your eJoni parked outside in extreme weather conditions.

  • Page 38: Cleaning And Maintenance

    Trio controller and cause irreversible damage to the unit. Your eJoni bicycle contains electrical parts that could be sensitive to damage if cleaned incorrectly. Only clean your bicycle by hand using a wet cloth and do not attempt to shower or submerge the unit.

  • Page 39: Disc Brakes

    DO NOT ALLOW brake fluid to contact skin or eyes. If fluid comes into contact with skin or eyes seek to dilute with plenty water and seek medical advice. The X35+ rear hub motor fitted to your eJoni is only compatible with rotor sizes from Ø160-180mm. www.islabikes.co.uk...
  • Page 40 Disc brakes continued YOU MUST only use Islabikes genuine replacement disc rotor bolts and washers. Failure to use the correct bolts and washers will void your warranty and damage the motor beyond repair. eJoni...
  • Page 41 Wheels Rim trueness – Depending on the type of riding you do your Islabikes bikes wheels may become untrue or damaged when riding. This means they will not spin straight and will wobble. If for any reason they are untrue our wheels can be easily repaired, please contact our technical support team on +44 (0) 1584 708 383 or email techsupport@islabikes.co.uk.

  • Page 42: Tyres And Tubes

    Inflate to correct pressure and then carefully re- tighten to close the valve. Valve closed Valve open Use our guide to inflate your tyres, https://www.islabikes.co.uk/knowledge/ technical-support/maintaining-your-islabike/ eJoni...
  • Page 43 +44 (0) 1584 708 383 or email techsupport@islabikes.co.uk. Headset Servicing – The eJoni headset uses sealed cartridge bearings, however, this headset will still need regular maintenance. The headset bearings should be removed, cleaned, checked for wear and reinstalled with fresh grease.

  • Page 44: Recommended Torque Settings

    We only recommend using genuine parts for safety critical components e.g. brake cables, brake blocks and bolts. Your eJoni is fitted with a rear hub motor which makes the specification, quality and correct installation of all wheelset components critically important. If you should experience any issues...

  • Page 45: Frame Number

    Please make a record of your frame number. This is a combination of letters and numbers unique to your bike stamped to the underside of the frame. This is required by police and insurance companies in case of loss. Islabikes do not keep a record of this. Frame number...

  • Page 46: Supplementary Notes

    2. The A-weighted emission sound pressure level at the rider’s ears is less than 70 dB(A). 3. Islabikes and Mahle SmartBike Systems accept no responsibility for modifications made to the EPAC through tampering with any of the electronic components fitted.
  • Page 47 UK Declaration of conformity Product Name: Islabikes eJoni Manufacturer Address: Islabikes Ltd, Unit 10 Lower Barns Business Park, Ludlow, Shropshire, SY8 4DS, UK This declaration of conformity is issued under the sole responsibility of the manufacturer, Islabikes Ltd. The object of the declaration is the...
  • Page 48 www.islabikes.co.uk...

Table of Contents