Timotion TDH5 User Manual
  1. Manuals
  2. Brands
  3. Timotion Manuals
  4. Gate Opener
  5. TDH5
  6. User manual

Timotion TDH5 User Manual

Hide thumbs

Advertisement

Table of Contents

Hand Control Programming- TDH5
20210811
User Manual
Hand Control
Programming-
TDH5
Version 4 August 2021
1 of 15

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the TDH5 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Timotion TDH5

Summary of Contents for Timotion TDH5

  • Page 1 Hand Control Programming- TDH5 20210811 User Manual Hand Control Programming- TDH5 Version 4 August 2021 1 of 15...

  • Page 2: Table Of Contents

    Hand Control Programming- TDH5 Contents Contents ..................................2 Disclaimer .................................. 3 1. User Interface Guide ............................. 4 2. Reset ..................................5 3. Adjusting the Height ............................. 6 4. Setting the Memorized Position ........................... 6 5. Setting the Upper and Lower Height Limit ......................7 6.

  • Page 3: Disclaimer

    Hand Control Programming- TDH5 Disclaimer This user manual is ONLY for generic TiMOTION products. Manufacturers may have altered product settings causing them to differ from this user manual. Please contact the manufacturer for a revised manual if the product settings are different than this manual.

  • Page 4: User Interface Guide

    Hand Control Programming- TDH5 1. User Interface Guide 3-digit height display Up and down buttons Memory setting buttons Version 4 August 2021 4 of 15...

  • Page 5: Reset

    Hand Control Programming- TDH5 2. Reset Simultaneously press for 3 seconds. Continue pressing the buttons until both columns are in the lowest position. When finished with the reset, the control box will make a “beep” sound, and the buttons can be released.

  • Page 6: Adjusting The Height

    Press button until the desk reaches the preferred height. 4. Setting the Memorized Position TDH5 supports a maximum of 4 memory positions. How to memorize a position: Adjust the desk to the desired height. Press the preferred memory button (1, 2, 3, 4), with either for 2 seconds.

  • Page 7: Setting The Upper And Lower Height Limit

    Hand Control Programming- TDH5 5. Setting the Upper and Lower Height Limit Setting the upper height limit: (1) Adjust the desk to the preferred upper height limit. (2) Press buttons together for less than 3 seconds, holding and release button..

  • Page 8: Presetting The Desk Starting Height

    Hand Control Programming- TDH5 6. Presetting the Desk Starting Height (1) Press the button until the desk reaches its lowest position, then release the button. Re-press button again for 5 seconds, and the digital display will flash for 10 seconds.

  • Page 9: Adjusting Built-In T-Touch Or Tcs1 Sensitivity

    Hand Control Programming- TDH5 8. Adjusting built-in T-touch or TCS1 sensitivity Press memory buttons 1 & 2 for 5 seconds, the display will show the current sensitivity level (0~9) by flashing. (Note 4) Press the button to adjust the sensitivity level. If no button is pressed within 5 seconds, the system will resume normal operation mode.

  • Page 10: Restore Factory Setting

    Hand Control Programming- TDH5 10. Restore Factory Setting (1) Refer to Chapter 2-Reset: after the “beep” sound, press buttons together for 15 seconds, the control box will twice make a “beep” sound, and the digital display will show “---. “...
  • Page 11 Hand Control Programming- TDH5 again. Overuse Operating over the Wait for about 5 minutes, and 3 beeps duty cycle’s normal the desk will be operational protection Time andfrequency. again. Unbalanced 1) Even out the load on the 2 beeps A Desk tilt is desk and perform a reset.
  • Page 12 Hand Control Programming- TDH5 replaced. M2 motor M2 motor is Remove the heavy load 5 beeps overcurrent overloaded and the desk will return protection back to normal operation. 2) If the desk still cannot be operated normally, perform a reset and operate the desk.
  • Page 13 Hand Control Programming- TDH5 2) If a reset can't be performed, or the error keeps being triggered after a reset, the M4 column is defective and needs to be replaced. No signal Signal from M1 is Unplugthe motor cable, 1 long beep...
  • Page 14 Hand Control Programming- TDH5 a reset, the M3 column is defective and needs to be replaced. No signal Signal from M4 is Unplugthe motor cable, 1 long beep feedback from not detected wait a moment, then plug it back in.
  • Page 15 Hand Control Programming- TDH5 No power No current is detected Unplugthe motor cable, 4 beeps consumption from M3 wait a moment, then plug from M3 it back in. Perform a reset and operate the desk. If a reset can't be...

Table of Contents

Save PDF