Hix N-680D Owner's Manual

15”x15” / 16”x20” air automatic heat transfer machines

Hide thumbs

Quick Links

N-680

15"x15" / 16"x20" Air Automatic Heat Transfer Machines

OWNER'S MANUAL

N-680

For Customer Service, Call 1-800-835-0606

CONTENTS

Receiving & Installation

Temperature & Time Instructions

Pressure Control

Maintenance Schedule

BEFORE warranty repair you MUST get Prior Authorization:

or Visit www.hixcorp.com

/ N-880

N-880

2-3

4-5

5-6

8-10

70146 RV D_101310

Need help?

Do you have a question about the N-680D and is the answer not in the manual?

Questions and answers

Summary of Contents for Hix N-680D

Page 1: Table Of Contents
N-680 / N-880 15”x15” / 16”x20” Air Automatic Heat Transfer Machines OWNER’S MANUAL N-680 N-880 For Customer Service, Call 1-800-835-0606 or Visit www.hixcorp.com CONTENTS Receiving & Installation Temperature & Time Instructions Auto Shut Off Pressure Control Transfer Application Relay Bypass Repairs Maintenance Schedule Troubleshooting...
Page 2: Receiving & Installation
RECEIVING & INSTALLATION SHIPPING OR RETURNS NOTE: Save all of your shipping/packing materials. DO NOT RISK COSTLY SHIPPING DAMAGE! SHIP ONLY IN ORIGINAL BOX. 1. Fasten machine to plywood shipping base with bolts provided. 2. Tie or tape handle securely to base. 3.
Page 3: Temperature & Time Instructions
Damage to the machine’s internal air operated components can occur that will not be covered under warranty. Combination air filter/water traps are available at any major hardware store or may be purchased directly from HIX (part #71145). OPERATION Digital Display For Class D Models DIGITAL TEMPERATURE &...
Page 4: Auto Shut Off
AUTO SHUT OFF FEATURE NOTE: This machine is programmed from the factory to turn the heat off after 3 hours of non use. One Minute before the machine is going into “Auto Shut Down” mode, the controller will “BEEP” five times to alert the operator that the machine is about to shut the heat off.
Page 5: Transfer Application
TRANSFER APPLICATION The 120 volt models have a slower heat recovery (i.e. 18-20 seconds @ 375°F). The 220 volt models are recommended for quicker cycle times (i.e. 10 seconds @ 375°F). 1. Set the temperature, time, & pressure to the desired settings as instructed.
Page 6 TRANSFER APPLICATION When you fail to make a successful transfer you can wonder, “Is it the machine’s fault, or the transfer, wrong settings or what”? FIRST, THE BASICS: 1. Be sure to set the heat transfer machine to the transfer manufacturer’s recommended Temperature, Time and Pressure settings.
Page 7: Relay Bypass
REPAIRS RELAY BYPASS WARNING: Before making repairs, be sure ON/OFF switch is OFF and machine is unplugged! ATTENTION: Eteindre la machine avant de faire des réparations. 1. Remove the back cover of the machine. WARNING: To prevent posible electrical shock, unplug the machine before removing cover to service.
Page 8: Troubleshooting
TROUBLESHOOTING WARNING: Before making repairs, be sure on/off switch is off and machine is unplugged! *Customer Service Tech Sheets are available for this step. Visit www.hixcorp.com to print or call 620-231-8568 and we will send you one. Parts ordering is available on-line.
Page 9 TROUBLESHOOTING WARNING: Before making repairs, be sure on/off switch is off and machine is unplugged! *Customer Service Tech Sheets are available for this step. Visit www.hixcorp.com to print or call 620-231-8568 and we will send you one. Parts ordering is available on-line.
Page 10 TROUBLESHOOTING WARNING: Before making repairs, be sure on/off switch is off and machine is unplugged! *Customer Service Tech Sheets are available for this step. Visit www.hixcorp.com to print or call 620-231-8568 and we will send you one. Parts ordering is available on-line.
Page 11 NOTES...
Page 12: Warranty
In the event of a defect, HIX, at its option, will repair, replace or substitute the defective item at no cost during this period subject to the limitations of insurance and shipping costs stated below.

This manual is also suitable for:

N-880d