Summary of Contents for Thermo Scientific Lindberg Blue M 3055 Series
Page 1
Lindberg Blue M Performance Ovens 3055 and 3056 Series Operating Manual and Parts List LT2148X3 Rev. 0 _________________________________________________________________________________ Part of Thermo Fisher Scientific...
Page 2
Forced Air LB305565G (6943) 5 cu ft (Large) 120V Gravity LB305665M (6946) 5 cu ft (Large) 120V Forced Air MANUAL NUMBER LT2148X3 (7006941) 4/15/10 Transfer to Marietta (was LT2148X3 2/15/10) ECR/ECN DATE DESCRIPTION Thermo Scientific Lindberg Blue M Performance Oven...
Page 4
Always use the proper protective equipment (clothing, gloves, goggles, etc.) 4 Always dissipate extreme cold or heat and wear protective clothing. 4 Always follow good hygiene practices. 4 Each individual is responsible for his or her own safety. Thermo Scientific Lindberg Blue M Performance Oven...
Page 5
We can also provide you with a quotation on our Extended Warranty for your Thermo Scientific products. Whatever Thermo Scientific products you need or use, we will be happy to discuss your applications. If you are experiencing technical problems, working together, we will help you locate the problem and, chances are, correct it yourself...over the telephone without a service...
Introduction Section 1 Thermo Scientific Lindberg Blue M 3055 & 3056 Series premium ovens are available in three sizes: small, medium and large. All ovens provide PID Microprocessor control at operating temperatures ranging from 50°C (122°F) to 275°C (527°F). The forced air models provide improved temperature uniformity and control, as well as faster drying.
Unpacking Thermo Scientific Lindberg Blue M ovens are shipped in a single carton. After unpacking, locate each item shown in the list below. Report any missing items, by name and part number, to your Thermo Scientific distributor.
Press the 0 (lower) half in to turn off oven power. To reset the breaker, first place the switch to the Off position, then return it to the On position. Lindberg Blue M Performance Oven Thermo Scientific...
Alarm Indicator - Lights if the actual oven temperature exceeds the alarm temperature. The alarm temperature is factory-adjusted to be 5°C above the set temperature. Program Indicator - Lights when the control temperature is being set. Thermo Scientific Lindberg Blue M Performance Oven...
Pressing SET causes the display to show the set temperature. Used with INCREASE and DECREASE to change the set temperature or with MENU to access entry of a temperature display offset. Lindberg Blue M Performance Oven Thermo Scientific...
Note To rapidly increase or decrease the set temperature, press and hold the appropriate arrow key. To slowly increment or decrease the set temperature one degree at a time, press and immediately release the arrow key. Thermo Scientific Lindberg Blue M Performance Oven...
140°C. The oven immediately goes in to alarm once the set point is reset to 140 from 160. The oven will stay in alarm until the oven temperature cools down to 144.9° (140,+5,-0.1). Lindberg Blue M Performance Oven Thermo Scientific...
The calibrated thermometer reads 151°C. A display offset of 1 is entered. The immediate display reads 151. The oven cools to 150°C, the display reads 150 and the calibrated thermometer reads 150. Thermo Scientific Lindberg Blue M Performance Oven...
1. Set the power switch to off position and open chamber door. 2. Open door fully. Carefully remove and retain hardware from door hinges (case side). Lay door on a flat surface with the handle over the edge. Thermo Scientific Lindberg Blue M Performance Oven...
2. Remove the two mounting screws holding defective handle in place. 3. Mount the replacement handle using two screws. 4. Adjust bottom nut (13/16) from end of shaft. 5. Secure latch cover in place with two screws. Lindberg Blue M Performance Oven Thermo Scientific...
The top clips will come loose but the wiring will still be connected. 7. Carefully set the bezel on the bench. Thermo Scientific Lindberg Blue M Performance Oven...
4. Remove the two screws securing heater to cabinet. Slide heater forward to disengage back heater clips, lift back of heater up, then slide heater back and lift out. 5. Install replacement heater and reassemble oven by generally reversing the steps above. Lindberg Blue M Performance Oven Thermo Scientific...
10. Install replacement fan and reassemble oven by generally reversing the steps above. Note When installing the replacement fan, make certain air flow arrow molded into fan housing points into the oven chassis. Thermo Scientific Lindberg Blue M Performance Oven...
12. Detach the controller housing (oven bottom) by removing the eight screws which fasten it to the cabinet. Two screws are located on each side of the oven and four on the bottom of the oven. (continued) Lindberg Blue M Performance Oven Thermo Scientific...
7. Carefully set the bezel on the bench. 8. Locate terminal blocks on controller, remove all wires connected to controller. Note color and location of wires. Thermo Scientific Lindberg Blue M Performance Oven...
7. Carefully set the bezel on the bench. 8. Consult the schematic and locate the solid state relay (mounted on bezel). 9. Remove four lead wires from their screw-down terminals. Lindberg Blue M Performance Oven Thermo Scientific...
10. Remove two Phillips screws which mount the safety relay to the bezel. 11. Lift out the safety relay. 12. Generally reverse the steps above to install the replacement safety relay and re-assemble oven. Thermo Scientific Lindberg Blue M Performance Oven...
1 through 10 to complete installation of new thermocouple and reassemble oven. Caution Verify the yellow thermocouple conductor is under the (+) tab and the red thermocouple conductor is under the (-) tab. 6-10 Lindberg Blue M Performance Oven Thermo Scientific...
Replace control thermocouple Check thermocouple connections at rear of temperature Faulty or broken connections controller Temperature off from Independent Begin by setting offset to 0. See Display Calibration offset needs adjusted. thermometer Offsets. Thermo Scientific Lindberg Blue M Performance Oven...
Replacement Parts Section 8 Replacements for oven parts may be ordered, by part number, from Thermo Scientific Technical Services. Note Only factory authorized components should be used for repair. Item Part Number (ref) Line Cord and Plug CRX121 Temperature Controller...
Page 33
Section 8 Schematics Lindberg Blue M Performance Oven Thermo Scientific...
Page 34
Thermo Scientific 401 Millcreek Road Marietta, Ohio 45750 United States www.thermofisher.com...