Yamaha MT-10 2021 Owner's Manual
  1. Manuals
  2. Brands
  3. Yamaha Manuals
  4. Motorcycle
  5. MT-10 2021
  6. Owner's manual

Yamaha MT-10 2021 Owner's Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

MOTORCYCLE
Read this manual carefully
before operating this vehicle.
B5Y-28199-10
Instrument and control functions
For your safety - pre-operation checks
Operation and important riding points
Periodic maintenance and adjustment
Motorcycle care and storage
Specifications
Consumer information
1
2
3
4
5
6
7
8
9
10
11
12
Index

Advertisement

Table of Contents
loading

Related Manuals for Yamaha MT-10 2021

Summary of Contents for Yamaha MT-10 2021

  • Page 1: Table Of Contents

    Read this manual carefully before operating this vehicle. Location of important labels OWNER’S MANUAL Safety information Description Special features Instrument and control functions For your safety – pre-operation checks Operation and important riding points Periodic maintenance and adjustment Motorcycle care and storage MOTORCYCLE Specifications MT10N/MT10NC (MT-10)
  • Page 2 EAU10045 Operating, servicing and maintaining a passenger vehicle or off-road vehicle can expose you to chemicals including engine exhaust, carbon monoxide, phthalates, and lead, which are known to the State of California to cause cancer and birth defects or other reproductive harm. To minimize exposure, avoid breathing exhaust, do not idle the engine except as necessary, service your vehicle in a well-ventilated area and wear gloves or wash your...
  • Page 3 Yamaha has met these standards without reducing the performance or economy of operation of the motorcycle. To maintain these high standards, it is important that you and your Yamaha dealer pay close attention to the recommended maintenance schedules and operating instructions contained within this manual.
  • Page 4 Important manual information EAU10134 Particularly important information is distinguished in this manual by the following notations: This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.

  • Page 5: Owner's Manual

    Important manual information EAU10194 MT10N/MT10NC OWNER’S MANUAL ©2022 by Yamaha Motor Corporation, U.S.A. 1st edition, December 2021 All rights reserved. Any reprinting or unauthorized use without the written permission of Yamaha Motor Corporation, U.S.A. is expressly prohibited. Printed in Japan.
  • Page 6 EXUP system ....... 5-37 Tires..........8-17 Special features ......4-1 Auxiliary DC jack ......5-37 Cast wheels ......... 8-20 YRC (Yamaha Ride Control) ..4-1 Sidestand ........5-38 Adjusting the clutch lever free Glossary ......... 4-4 Ignition circuit cut-off system..5-39 play...........
  • Page 7 Checking the steering....8-29 MOTORCYCLE LIMITED Checking the wheel bearings ..8-30 WARRANTY ......11-8 Battery .......... 8-30 YAMAHA EXTENDED SERVICE Replacing the fuses ...... 8-31 (Y.E.S.) ........11-10 Vehicle lights ........ 8-33 Supporting the motorcycle.... 8-34 Index ..........12-1 Troubleshooting......

  • Page 8: Location Of Important Labels

    Read and understand all of the labels on your vehicle. They contain important information for safe and proper operation of your vehicle. Never remove any labels from your vehicle. If a label becomes difficult to read or comes off, a replacement label is available from your Yamaha dealer. 4, 5...
  • Page 9 Location of important labels 4 California only WARNING VACUUM HOSE ROUTING BEFORE YOU OPERATE THIS VEHICLE, READ THE OWNER’S MANUAL AND ALL LABELS. ALWAYS WEAR AN APPROVED MOTORCYCLE PRESS. SENSOR HELMET, eye protection, and protective clothing. PREMIUM UNLEADED GASOLINE ONLY 91 Min.

  • Page 10: Safety Information

    Safety information EAU1028C Take a training course. Beginners • Use extra caution when you are should receive training from a cer- approaching passing tified instructor. Contact an autho- through intersections, since in- Be a Responsible Owner rized motorcycle dealer to find out tersections are the most likely As the vehicle’s owner, you are respon- about the training courses nearest...
  • Page 11 Safety information tice riding your motorcycle with both hands and keep both control levers, footrests, or wheels where there is no traffic until you feet on the passenger footrests. and cause injury or an accident.  have become thoroughly famil- Never carry a passenger unless Always wear protective clothing iar with the motorcycle and all of...
  • Page 12 Yamaha accessories, which are avail- to minimize imbalance or instabili- of the motorcycle is changed. To avoid able only from a Yamaha dealer, have the possibility of an accident, use ex- been designed, tested, and approved ...
  • Page 13 Yamaha, even if sold and limit suspension travel, steering not recommended.  installed by a Yamaha dealer.
  • Page 14 Safety information  Check that the fuel cock (if equipped) is in the off position and that there are no fuel leaks.  Shift the transmission into gear (for models with a manual transmis- sion).  Secure motorcycle with tie-downs or suitable straps that are attached to solid parts of the motorcycle, such as the frame or upper front fork triple clamp (and...

  • Page 15: Description

    Description EAU10411 Left view 2, 3, 4 10 9 7, 8 1. Headlights (page 8-33) 9. Spring preload adjuster (page 5-34) 2. Spring preload adjuster (page 5-32) 10.Rebound damping force adjuster (page 5-34) 3. Rebound damping force adjuster (page 5-32) 11.Shift pedal (page 5-25) 4.

  • Page 16: Right View

    Description EAU10421 Right view 3, 4, 5 1. Tool kit (page 8-2) 9. Rear brake fluid reservoir (page 8-23) 2. Fuel tank cap (page 5-28) 3. Spring preload adjuster (page 5-32) 4. Rebound damping force adjuster (page 5-32) 5. Compression damping force adjuster (page 5-32) 6.

  • Page 17: Controls And Instruments

    Description EAU10431 Controls and instruments 1. Clutch lever (page 5-25) 9. Brake lever (page 5-26) 2. Left handlebar switches (page 5-2) 3. Main switch/steering lock (page 5-1) 4. Instrument panel (page 5-4, 5-6) 5. Auxiliary DC jack (page 5-37) 6. Front brake fluid reservoir (page 8-23) 7.

  • Page 18: Special Features

    YRC (Yamaha Ride Control) when entering turns, when acceler- Yamaha Ride Control is a system that ating hard at a sharp lean angle, or incorporates numerous sensors and while braking, and it cannot prevent controls to support an improved riding front wheel slip or front wheel lift.
  • Page 19 Special features cally adjusts according to the vehicle’s EWA15433 ECA16801 WARNING NOTICE lean angle. To maximize acceleration, when the vehicle is upright a less The traction control system is not a Use only the specified tires. (See amount of traction control is applied. substitute for riding appropriately page 8-17.) Using different sized When cornering, a greater amount of...
  • Page 20 Special features ing. When the sensor on the shift rod from red zone detects the appropriate motion in the shift pedal, engine power output is mo-  and QS can be individu- mentarily adjusted to allow for the gear ally set. change to occur.

  • Page 21: Glossary

    PWR - Power delivery mode SC - Stability Control SCS - Slide Control System EWA20891 YRC - Yamaha Ride Control WARNING The brake control system is not a substitute for the use of proper rid- ing and braking techniques. The...

  • Page 22: Yrc Functions Visual Guide

    Special features EAU66912 YRC functions visual guide BC1/BC2 1. Start 6. Straightaway 2. Acceleration 3. Braking 4. Apex 5. Exit...

  • Page 23: Cruise Control System

    Special features EAU97470 tem indicator light “ ” is off. Activating and setting the cruise Cruise control system control system This model is equipped with a cruise 1. Push the cruise control/YVSL control system designed to maintain a power switch “ ”...
  • Page 24 Special features You can also manually increase your speed will return to the previously set traveling speed using the throttle. After cruising speed. The “ ” indicator light you have accelerated, you can set a will come on. new cruising speed by pushing the EWA16351 WARNING “SET–”...

  • Page 25: Yamaha Variable Speed Limiter (Yvsl)

    This model is equipped with the In some cases, the cruise control sys- has not been turned off, the trac- Yamaha variable speed limiter (YVSL) tem may not be able to maintain the set tion control system will operate which limits the vehicle to a maximum...
  • Page 26 Special features  To prevent accidentally activat- limit, apply the brakes. ing the YVSL system, turn it off When the YVSL disengages, engine when not in use. Make sure that output is gradually derestricted to en- the YVSL display is off. sure a smooth transition to full rider control of the throttle.
  • Page 27 If the color of the speed setting in- (5 mi/h).  dicator icon has changed and Push the cruise control/YVSL flashes, have a Yamaha dealer power switch “ ” located on the Deactivating the YVSL left handlebar. The YVSL display check the vehicle.
  • Page 28 Special features speed limit is too low for current conditions. Pushing the cruise control/YVSL power switch “ ” while the YVSL system is operating will turn the system off com- pletely and erase the previously set speed limit. You will not be able to use the resume function until a new speed limit has been set.

  • Page 29: Instrument And Control Functions

    Instrument and control functions EAU10462 without the engine running. To lock the steering Main switch/steering lock EAU10664 All electrical systems are off. The key can be removed. EWA10062 WARNING Never turn the key to “OFF” or LOCK “LOCK” while the vehicle is moving. Otherwise the electrical systems will 1.

  • Page 30: Handlebar Switches

    Instrument and control functions To unlock the steering EAU66057 Right Handlebar switches 1 1 1 Left 1. Stop/Run/Start switch “ ” 1. Push. 2. Wheel switch “ ” 2. Turn. 1. “MODE” switch Push the key in and turn it to “OFF”. EAU91630 2.
  • Page 31 Instrument and control functions 7-2 for starting instructions prior to EAU94151 Cruise control/YVSL switches starting the engine. See page 4-6 for an explanation of the Set this switch to “ ” to stop the engine cruise control system. in case of an emergency, such as when See page 4-8 for an explanation of the the vehicle overturns.

  • Page 32: Indicator Lights And Warning Lights

    Instrument and control functions til TCS OFF is displayed. To turn scroll up/left or increase a setting value. EAU4939X Indicator lights and warning the traction control system back Rotate down - rotate the wheel down- lights on, use the MODE down “ ”...
  • Page 33  corresponding turn signal lights are lem is detected in the engine. If this oc- Use extra caution to avoid pos- flashing. curs, have a Yamaha dealer check the sible wheel lock during emer- on-board diagnostic system. gency braking. ...

  • Page 34: Display

    When the vehicle is turned on, this light If the oil pressure and coolant warn- should come on for a few seconds and then go off. Otherwise, have a Yamaha ing light does not go off after start- ing the engine or if it comes on while dealer check the vehicle.
  • Page 35 Instrument and control functions STREET MODE TRACK MODE  This model uses a thin-film-tran- sistor liquid-crystal display (TFT 12 : 00 12 : 00 EBM 1 EBM 1 1000 r/min 1000 r/min LCD) for good contrast and read- ability in various lighting condi- GEAR tions.
  • Page 36 “ ”. circuits.  When the Yamaha variable speed When the Yamaha variable speed lim- limiter (YVSL) system is operating iter (YVSL) system is operating in in STREET MODE, the fuel meter TRACK MODE, the transmission gear is replaced by the YVSL display.
  • Page 37 ” started. function properly. Use extra care when 3. Oil pressure warning “ ” braking and have a Yamaha dealer 4. Fuel level warning “ ” check the vehicle immediately. 5. Error mode warning “Err” If a malfunction is detected, the oil pres- sure warning icon will flash repeatedly.
  • Page 38 Instrument and control functions sumed Air temperature: Coolant temperature: TRIP-1, TRIP-2, F-TRIP, FUEL CON, and FUEL AVG items can be individu- ally reset. A. TEMP C. TEMP A. TEMP C. TEMP The display items are grouped into 4 customizable pairs (DISPLAY 1-4). In TRACK MODE only a single item can be displayed at a time.
  • Page 39 Instrument and control functions Tripmeters: Fuel reserve tripmeter: Odometer: TRIP-1 1234.5 3330.0 TRIP-1 mile mile F-TRIP 123456 123456 F-TRIP mile mile mile mile TRIP-2 1234.5 6660.0 TRIP-2 mile mile 1. Display in STREET MODE 1. Display in STREET MODE 1. Display in STREET MODE 2.
  • Page 40 Instrument and control functions Cruise control speed setting: Average fuel consumption: Current fuel consumption: FUEL AVG CRNT FUEL FUEL AVG CRNT FUEL 1. Display in STREET MODE 1. Display in STREET MODE 1. Display in STREET MODE 2. Display in TRACK MODE 2.
  • Page 41 Instrument and control functions Fuel consumption trip meter: 2. STREET MODE: Short push the the indicator will start flashing. wheel switch and the item group 3. Rotate the wheel switch to select will flash for 5 seconds. If both the temperature preset. items in the group are resettable, 4.
  • Page 42 Instrument and control functions setting menu. (See MODE-D: street use or rainy weather page 5-16.) To change YRC modes or make setting 12 : 00 MODE - MODE - changes  1000 r/min YRC settings shown on the bottom 1. Use the “MODE” switch to scroll of the main screen (PWR, TCS, left to right and highlight the item GEAR...

  • Page 43: Menu Screen

    Instrument and control functions records up to forty laps. On the main 2. While the information display item EAU93645 MENU screen screen, the lap timer shows the current is flashing, rotate the wheel switch lap time and lap number (indicated by upward.
  • Page 44 Instrument and control functions exit the MENU and return to the adjusting the setting levels (or on/off Brightness Adjust screen brightness main display. status as applicable) of YRC items Grip Warmer Adjust grip warmer presets Setting (if equipped)  To ensure that the desired settings PWR, TCS, SCS, QS “...
  • Page 45 Instrument and control functions SCS can be set to OFF, 1, 2, and 3.  The traction control system can OFF turns the slide control system off, only be turned off completely via setting level 1 provides the least sys- the main screen using the “MODE”...
  • Page 46 Instrument and control functions control system also regulate brake YRC Setting 10 : 00 LIF can be set to 1, 2, 3, or OFF. Setting pressure while cornering to suppress level 3 most strongly reduces wheel lift, lateral wheel slip. and setting level 1 provides the least system intervention.
  • Page 47 Instrument and control functions lete the lap time record. The fastest lap YRC Setting 10 : 00 and the average lap time stored in the 10 : 00 Lap Time lap time record are displayed at the top Display of the screen. Use the wheel switch to scroll and see all lap times.
  • Page 48 Instrument and control functions 2. Long push the wheel switch to re- set the item. 10 : 00 Unit GP GPS km or mile mile 10 : 00 Maintenance mile INTERVAL 1 123456 mile INTERVAL 2 123456 mile 1. Photo sensor “Wallpaper”...
  • Page 49 Instrument and control functions Shift Indicator 12 : 00 Shift Indicator 12 : 00 10 : 00 MENU GP GPS 1000 r/min 1000 r/min Shift Indicator Shift IND Setting Shift IND Setting Display Setting IND Mode IND Mode Brightness IND Start 6000 IND Start 7000...
  • Page 50 Instrument and control functions range is 5500–13000 r/min. mid-to-high r/min zones can be set to come on in green and then orange col- Shift Indicator 12 : 00 ors. 1000 r/min The blue area on the tachometer indi- 1. Select “IND Mode”. cates the currently set operational Tach IND Setting IND Mode...
  • Page 51 Instrument and control functions 5. Select “Tach IND 2nd”. “Peak Rev IND Setting” This module allows you to turn the rev- 12 : 00 EBM 1 olution peak hold indicator on or off. Shift Indicator 12 : 00 1000 r/min 1000 r/min “Display Setting”...
  • Page 52 Instrument and control functions ODO: odometer “Grip Warmer Setting” (if equipped) SPEED: cruise control speed set- This module is for adjusting the temper- 10 : 00 Display Setting ting ature values for the grip warmer pre- DISPLAY-1 FUEL AVG: average fuel consumption sets (LO/MIDDLE/HIGH).

  • Page 53: Clutch Lever

    Instrument and control functions EAU12823 EAU83692 shifter is programmed to ignore unclear Clutch lever Shift pedal input signals. Therefore, be sure to shift using quick and sufficiently forceful in- puts. 1 1 1 1 1. Clutch lever 1. Shift pedal 2.

  • Page 54: Brake Lever

    Instrument and control functions EAU93080 EAU12944 EAU94200 Brake lever Brake pedal Brake control system (BC) The brake control system regulates hy- 1 1 1 draulic brake pressure for the front and rear wheels independently when the brakes are applied and wheel lock is detected.
  • Page 55 Instrument and control functions EWA16051 test when the vehicle is started and WARNING reaches a speed of 5 km/h (3 mi/h). During this test, a clicking noise may be Always keep a sufficient distance audible from the hydraulic control unit, from the vehicle ahead to match the 2 2 2 and a vibration may be felt at the brake...

  • Page 56: Fuel Tank Cap

    Instrument and control functions EAU13077 the key cannot be removed if the cap is EAU13222 Fuel tank cap Fuel not properly closed and locked. Make sure there is sufficient gasoline in EWA11092 the tank. WARNING EWA10882 Make sure that the fuel tank cap is WARNING 2 2 2 properly closed after filling fuel.
  • Page 57 ECA11401 EAU86110 NOTICE Use only unleaded gasoline. The use Your Yamaha engine was designed to use premium unleaded gasoline. Con- of leaded gasoline will cause severe 1. Fuel tank filler tube damage to internal engine parts, firm the pump octane number [(R+M)/2 2.

  • Page 58: Fuel Tank Breather Hose And Overflow Hose

    Instrument and control functions EAU97850 For California ter information. Fuel tank breather hose and overflow hose For U49 models 1 1 1 1 1 1 1. Clamp 2. Fuel tank overflow hose The breather hose prevents a vacuum condition from forming within the fuel 1.

  • Page 59: Catalytic Converter

    Instrument and control functions EAU13435 EAU94110 Catalytic converter Seat The exhaust system contains catalytic converter(s) to reduce harmful exhaust To remove the seat emissions. 1. Open the seat lock cover, insert EWA10863 the key into the seat lock, and then WARNING turn the key counterclockwise.

  • Page 60: Adjusting The Front Fork

    Instrument and control functions  Do not subject the IMU to strong EAU70414 To set the spring preload, turn the ad- Adjusting the front fork shocks. juster in direction (b) until it stops, and This model is equipped with adjustable then count the turns in direction (a).
  • Page 61 Instrument and control functions Rebound damping force Turn the adjusting bolt in direction (a) to 1 1 1  When turning the damping force increase the rebound damping force. adjuster in direction (a), the 0 click Turn the adjusting bolt in direction (b) to (a (a) (b (b) position and the 1 click position...

  • Page 62: Adjusting The Shock Absorber Assembly

    Instrument and control functions suspension. EAU74243 ed in the tool kit to make the ad- Adjusting the shock absorber justment. assembly This model is equipped with adjustable suspension. The spring preload, re- bound damping force, fast compres- sion damping force, slow 2 2 3 3 compression damping force can be ad-...
  • Page 63 Instrument and control functions suspension. Spring preload: Minimum (soft): (a (a) (b (b) Distance A = 76.5 mm (3.01 in) Compression damping force Standard: Distance A = 80.5 mm (3.17 in) Fast compression damping force Maximum (hard): Distance A = 84.5 mm (3.33 in) Turn the adjusting bolt in direction (a) to increase the compression damping 3.
  • Page 64 Take the shock stops, and then count the clicks in di-  When turning the damping force absorber assembly to a Yamaha rection (b). adjuster in direction (b), it may click dealer for any service. beyond the stated specifications,...

  • Page 65: Luggage Strap Holders

    EAU67050 EAU49454 Luggage strap holders EXUP system Auxiliary DC jack This model is equipped with Yamaha’s EXUP (EXhaust Ultimate Power valve) system. This system boosts engine power by means of a valve that controls exhaust flow within the exhaust cham- 1 1 1 ber.

  • Page 66: Auxiliary Dc Jack

    Instrument and control functions 3. Turn the accessory off. EAU15306 Yamaha dealer repair it if it does not Sidestand 4. Insert the accessory plug into the function properly. The sidestand is located on the left side auxiliary DC jack. of the frame. Raise the sidestand or lower it with your foot while holding the vehicle upright.

  • Page 67: Ignition Circuit Cut-Off System

    Instrument and control functions EAU57952 Ignition circuit cut-off system This system prevents in-gear engine starts unless the clutch lever is pulled and the sidestand is up. Also, it will stop the running engine should the sides- tand be lowered while the transmission is in gear.
  • Page 68 The neutral switch may not be working. 6. Move the sidestand up. The motorcycle should not be ridden until 7. Pull the clutch lever. checked by a Yamaha dealer. 8. Shift transmission into gear. 9. Move the sidestand down. Does the engine stall? The sidestand switch may not be working.

  • Page 69: For Your Safety - Pre-Operation Checks

    • If necessary, add recommended coolant to specified level. 8-14 • Check cooling system for leakage. • Check operation. • If soft or spongy, have Yamaha dealer bleed hydraulic system. • Check brake pads for wear. Front brake • Replace if necessary.
  • Page 70 • Tighten if necessary. Instruments, lights, signals • Check operation. — and switches • Correct if necessary. • Check operation of ignition circuit cut-off system. Sidestand switch 5-38 • If system is not working correctly, have Yamaha dealer check vehicle.

  • Page 71: Operation And Important Riding Points

    The vehicle can now be operated nor- there is a control or function you do not between 0 and 1600 km (1000 mi). For mally. understand, ask your Yamaha dealer. this reason, you should read the follow- ECA10311 NOTICE EWA10272 ing material carefully.

  • Page 72: Starting The Engine

    1 1 1 not work as described above, have a position or Yamaha dealer check the vehicle.  the transmission is in gear, the sid- estand is up, and the clutch lever is 3. Shift the transmission into the neu- pulled.

  • Page 73: Shifting

    Operation and important riding points EAU68221 EAU67084 pedal firmly until you feel the Shifting gear shift is complete.  Even with the transmission in the neutral position, do not This model is equipped with: coast for long periods of time ...
  • Page 74 Operation and important riding points the throttle, and at the same time, to downshift as necessary. acceleration deceleration quickly pull the clutch lever in. 4. Once the motorcycle has stopped, shown in the table below. 5. Shift the transmission into second the transmission can be shifted Shift up points: gear.

  • Page 75: Parking

    Operation and important riding points EAU17214 Parking When parking, stop the engine, and then remove the key from the main switch. EWA10312 WARNING  Since the engine and exhaust system can become very hot, park in a place where pedestri- ans or children are not likely to touch them and be burned.

  • Page 76: Periodic Maintenance And Adjustment

    – possibly leading to pending on the weather, terrain, geo- that is certified (if applicable). Yamaha death. See page 2-2 for more in- graphical location, and individual use, dealers are trained and equipped to...

  • Page 77: Tool Kits

    Periodic maintenance and adjustment EAU85240 your Yamaha dealer perform it for you. Tool kits 1. Tool kit The on–board tool kit is in the location shown. Also, an additional tool kit was handed out separately at the time of ve- hicle purchase.

  • Page 78: Periodic Maintenance Chart For The Emission Control System

    From 24000 mi (37000 km) or 36 months, repeat the maintenance intervals starting from 8000 mi (13000 km) or 12 months.  Items marked with an asterisk require special tools, data and technical skills, have a Yamaha dealer perform the service. EAU17602 Periodic maintenance chart for the emission control system...
  • Page 79 Periodic maintenance and adjustment INITIAL ODOMETER READINGS 600 mi 4000 mi 8000 mi 12000 mi 16000 mi 20000 mi ITEM ROUTINE (1000 km) (7000 km) (13000 km) (19000 km) (25000 km) (31000 km) 1 month 6 months 12 months 18 months 24 months 30 months Evaporative...

  • Page 80: General Maintenance And Lubrication Chart

    30 months • Perform dynamic inspection using Diagnostic system       Yamaha diagnostic tool. check • Check the error codes. 2 * Air filter element • Replace. Every 24000 mi (37000 km) • Check operation.  ...
  • Page 81 Periodic maintenance and adjustment INITIAL ODOMETER READINGS 600 mi 4000 mi 8000 mi 12000 mi 16000 mi 20000 mi ITEM ROUTINE (1000 km) (7000 km) (13000 km) (19000 km) (25000 km) (31000 km) 1 month 6 months 12 months 18 months 24 months 30 months •...
  • Page 82 Front and rear brake       29 * • Check operation. switches • Apply Yamaha cable lubricant or       30 * Control cables other suitable cable lubricant thoroughly. • Check operation.
  • Page 83 Periodic maintenance and adjustment EAU17653  Air filter • This model uses a disposable oil-coated paper element. This element cannot be cleaned with compressed air, doing so will only damage it. • Replace the air filter more frequently if you often ride in the rain or dusty conditions. ...

  • Page 84: Checking The Spark Plugs

    Do not attempt to diagnose wipe off any grime from the spark plug such problems yourself. Instead, have threads. a Yamaha dealer check the vehicle. If a spark plug shows signs of electrode Tightening torque: Spark plug (new): erosion and excessive carbon or other 18 N·m (1.8 kgf·m, 13 lb·ft)

  • Page 85: Canister (For California)

    Periodic maintenance and adjustment EAU19683 EAU73973 rial enters the crankcase. Canister (for California) Engine oil The engine oil level should be checked To check the engine oil level before each ride. In addition, the oil 1. After warming up the engine, wait must be changed and the oil filter car- a few minutes for the oil level to tridge replaced at the intervals speci-...
  • Page 86 Periodic maintenance and adjustment 5. Check the O-ring for damage, and replace if necessary. 6. Install the engine oil filler cap. To change the engine oil (and filter) 1. Start the engine, warm it up for several minutes, and then turn it off.
  • Page 87 Make sure that the O-ring is properly An oil filter wrench is available at a seated. Wipe off any spilled oil before starting Yamaha dealer. 6. Install a new oil filter cartridge, and the engine. 5. Apply a thin coat of clean engine then tighten to the specified 9.

  • Page 88: Why Yamalube

    Yamalube the best choice for level is sufficient. your Yamaha engine. ECA20860 NOTICE If the oil pressure warning light flick- ers or remains on even if the oil level is correct, immediately turn the en- gine off and have a Yamaha dealer 8-13...

  • Page 89: Coolant

    3. If the coolant is at or below the minimum level mark, remove the 5. Pull the coolant reservoir cover A If genuine Yamaha coolant is not avail- coolant reservoir cap by referring toward you as shown, and then re- able, use an ethylene glycol antifreeze to the following procedure.
  • Page 90 Periodic maintenance and adjustment coolant reservoir cap. Never at- Yamaha dealer check the anti- tempt to remove the radiator freeze content of the coolant as when engine soon as possible, otherwise the hot. effectiveness of the coolant will [EWA15162] be reduced.

  • Page 91: Air Filter Element

    Check the engine idling speed and, if maintenance and lubrication chart. necessary, have it corrected by a Have a Yamaha dealer replace the air Yamaha dealer. filter element. Engine idling speed: 1200–1400 r/min...

  • Page 92: Valve Clearance

    To pre- fied tires. Vehicle: vent this from occurring, have your 172 kg (379 lb) Yamaha dealer check and adjust the Tire air pressure The vehicle’s maximum load is the combined weight of the rider, passen- valve clearance at regular intervals.
  • Page 93 Yamaha ageing. Old and aged tires shall be dealer replace the tire immediately. checked by tire specialists to ascertain their suitability for further use.
  • Page 94 Note the fol- Otherwise, leakage may occur. lowing points in order to make the Have a Yamaha dealer inspect most efficient use of these tires. the valve.  Use only the specified replace- After extensive tests, only the tires list- ment tires.

  • Page 95: Cast Wheels

    If any 2. Loosen the locknut further down damage is found, have a Yamaha the clutch cable. dealer replace the wheel. Do not 3. To increase the clutch lever free...

  • Page 96: Checking The Brake Lever Free Play

    1 1 1 1. No brake lever free play There should be no free play at the brake lever end. If there is free play, have a Yamaha dealer inspect the brake system. EWA14212 WARNING A soft or spongy feeling in the brake lever can indicate the presence of air in the hydraulic system.

  • Page 97: Brake Light Switches

    Periodic maintenance and adjustment EAU36505 EAU22393 touches the brake disc, have a Yamaha Brake light switches Checking the front and rear dealer replace the brake pads as a set. The brake light should come on just be- brake pads fore braking takes effect. The brake...

  • Page 98: Checking The Brake Fluid Level

     lock. If the brake fluid level goes down suddenly, have a Yamaha dealer check the cause before further rid- ing. EWA15991 WARNING Improper maintenance can result in loss of braking ability.

  • Page 99: Changing The Brake Fluid

    EAU22734 EAU22762 Changing the brake fluid Drive chain slack Have a Yamaha dealer change the The drive chain slack should be brake fluid every 2 years. In addition, checked before each ride and adjusted have the seals of the master cylinders if necessary.

  • Page 100: Cleaning And Lubricating The Drive

    Periodic maintenance and adjustment 1. Loosen the axle nut and the lock- EAU23027 1 1 2 Cleaning and lubricating the nut on each side of the swingarm. drive chain 2. To tighten the drive chain, turn the drive chain slack adjusting bolt on The drive chain must be cleaned and each side of the swingarm in direc- lubricated at the intervals specified in...

  • Page 101: Checking And Lubricating The Cables

    Yamaha dealer at the ed if necessary. If a cable is damaged intervals specified in the periodic main- or does not move smoothly, have a tenance chart.

  • Page 102: Checking And Lubricating The Brake And Shift Pedals

    The brake lever pivot must be lubricat- ed by a Yamaha dealer at the intervals Brake pedal specified in the periodic maintenance and lubrication chart.

  • Page 103: Checking And Lubricating The Sidestand

    The operation of the sidestand should The swingarm pivots must be lubricat- Brake lever: be checked before each ride, and the ed by a Yamaha dealer at the intervals Silicone grease sidestand pivot and metal-to-metal specified in the periodic maintenance contact surfaces should be lubricated if and lubrication chart.

  • Page 104: Checking The Front Fork

    [EWA10752] have a Yamaha dealer check or re- tion. WARNING! To avoid injury, 2. Hold the lower ends of the front pair it. securely support the vehicle so...

  • Page 105: Checking The Wheel Bearings

    WARNING To charge the battery  Electrolyte is poisonous and Have a Yamaha dealer charge the bat- dangerous since it contains sul- tery as soon as possible if it seems to furic acid, which causes severe have discharged. Keep in mind that the burns.

  • Page 106: Replacing The Fuses

    Periodic maintenance and adjustment battery tends to discharge more quickly the main switch off, then con- EAU94164 Replacing the fuses if the vehicle is equipped with optional nect the positive lead before The main fuse, ABS motor fuse, and electrical accessories. connecting negative fuse boxes containing individual circuit...
  • Page 107 Periodic maintenance and adjustment 1 1 1 1 1 1 1 1 1 1. Fuse box 1 1. Fuse box 2 1. Fuse box 3 2. ABS solenoid fuse 2. Ignition fuse 2. Brake light fuse 3. Fuel injection system fuse 3.

  • Page 108: Vehicle Lights

    There are no user replaceable 7.5 A bulbs. ABS solenoid fuse: 15.0 A If a light does not come on, check the Fuel injection system fuse: fuses and then have a Yamaha dealer 15.0 A check the vehicle. Backup fuse: ECA16581 10.0 A NOTICE Electronic throttle valve fuse: 7.5 A...

  • Page 109: Supporting The Motorcycle

    1. Maintenance stand (example) self. However, should your motorcycle require any repair, take it to a Yamaha Since this model is not equipped with a dealer, whose skilled technicians have centerstand, use maintenance stands...

  • Page 110: Troubleshooting Chart

    Remove the spark plug and check the electrodes. The engine does not start. Have a Yamaha dealer check the vehicle. Check the compression. 4. Compression The engine does not start. There is compression.
  • Page 111 Start the engine. If the engine overheats again, have a The coolant level Yamaha dealer check and repair the cooling system. is OK. If coolant is not available, tap water can be temporarily used instead, provided that it is changed to the recommended coolant as soon as possible.

  • Page 112: Motorcycle Care And Storage

    Be  high-pressure washers of many components. Washing, clean- sure to consult a Yamaha dealer for steam-jet cleaners. Excessive ing, and polishing will also give you a advice on what products to use be- water pressure may cause water chance to inspect the condition of the fore cleaning the vehicle.
  • Page 113 Motorcycle care and storage gasoline, rust removers, brake hose. Use only enough pressure be sure to test all cleaning prod- fluid, or antifreeze, etc. to do the job. Avoid spraying water ucts before general applica- directly into the muffler, instrument tion.
  • Page 114 Motorcycle care and storage parts will become slippery, unpainted plastic parts. muffler. This should remove finger-  which could cause loss of con- Do not use abrasive polishing prints and other oil stains. If necessary, trol. Thoroughly clean the sur- compounds as they will wear an alkaline pH cleaning product and faces of these parts before...

  • Page 115: Storage

    Motorcycle care and storage EAU84141 perform any outstanding mainte- b. Pour a teaspoonful of engine oil Storage nance. into the spark plug bore. Always store the vehicle in a cool, dry 2. Follow all instructions in the Care c. Install the spark plug cap onto place.
  • Page 116 Motorcycle care and storage once a month in order to prevent the tires from becoming degraded in one spot. 9. Cover the muffler outlet with a plastic bag to prevent moisture from entering it. 10. Remove the battery and fully charge it, or attach a maintenance charger to keep the battery opti- mally charged.

  • Page 117: Specifications

    Specifications Dimensions: EAU84925 Starting system: Fuel reserve amount: Electric starter 4.0 L (1.06 US gal, 0.88 Imp.gal) Overall length: Engine oil: Fuel injection: 2100 mm (82.7 in) Overall width: Recommended brand: Throttle body: 800 mm (31.5 in) ID mark: Overall height: B5Y1 (MT10NC) 1165 mm (45.9 in) B5Y2 (MT10N)
  • Page 118 Specifications Manufacturer/model: Front turn signal light: BRIDGESTONE/BATTLAX HYPERS- PORT S22R Rear turn signal light: Loading: Auxiliary light: Maximum load: 172 kg (379 lb) License plate light: The vehicle’s maximum load is the combined weight of the rider, passenger, cargo and any accessories.

  • Page 119: Consumer Information

    These identification numbers are need- EAU26401 Vehicle identification number ed when registering the vehicle with the 1 1 1 authorities in your area and when or- dering spare parts from a Yamaha dealer. 1 1 1 VEHICLE IDENTIFICATION NUM- BER: 1.
  • Page 120 This information will be it for reference when ordering a new cover. This label shows specifications needed when ordering spare parts from key. related to exhaust emissions as re- a Yamaha dealer. quired by federal law, state law and En- vironment Canada. 11-2...

  • Page 121: Diagnostic Connector

    Vehicle data uploaded will be handled appropriately according to the following Privacy Policy. Privacy Policy https://yamaha-motor.com/ privacy-policy Yamaha will not disclose this data to a 11-3...

  • Page 122: Reporting Safety Defects

    If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Yamaha Motor Corporation, U.S.A. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.

  • Page 123: Motorcycle Noise Regulation

    Consumer information EAU26561 Motorcycle noise regulation TAMPERING WITH NOISE CONTROL SYSTEM PROHIBITED: Federal law prohibits the following acts or the causing thereof: (1) The removal or rendering inoperative by any person other than for purposes of maintenance, repair, or replacement of any device or element of design incorporated into any new ve- hicle for the purpose of noise control prior to its sale or delivery to the ultimate purchaser or while it is in use or (2) the use of the vehicle after such device or element of design has been removed or rendered inoperative by any person.

  • Page 124: Maintenance Record

    Consumer information EAU26633 Maintenance record Copies of work orders and/or receipts for parts purchased and installed on your vehicle will be required to document that maintenance has been completed in accordance with the emissions warranty. The chart below is printed only as a reminder that maintenance work is required.
  • Page 125 Consumer information Maintenance Date of Servicing dealer Mileage Remarks interval service name and address 36000 mi (55000 km) or 54 months 40000 mi (61000 km) or 60 months 11-7...

  • Page 126: Yamaha Motor

    Consumer information EAU61803 YAMAHA MOTOR CORPORATION, U.S.A. 2020 AND LATER MODEL STREET & DUAL-PURPOSE MOTORCYCLE LIMITED WARRANTY Yamaha Motor Corporation, U.S.A. hereby warrants that Give notice to an authorized Yamaha motorcycle ENGINE DISPLACEMENT each new Yamaha motorcycle purchased from an...

  • Page 127: Warranty

    CUSTOMER SERVICE What costs are my responsibility during the warranty period? If your machine requires warranty service, you must take it to any authorized Yamaha The customer’s responsibility includes all costs of normal maintenance services, motorcycle dealer within the continental United States. Be sure to bring your warranty non-warranty repairs, accident and collision damages, and oil, oil filters, air filters, registration card or other valid proof of the original date of purchase.

  • Page 128: Yamaha Extended Service (Y.e.s.)

    This excellent Y.E.S. plan coverage is only available to warranty. See the sample contract at your Yamaha Yamaha owners like you, and only while your Yamaha is still dealer to see how comforting uninterrupted factory- within the Yamaha Limited Warranty period. So visit your backed protection can be.
  • Page 129 TRIP coverage right away, and you’ll rest easy knowing you’ll have strong factory-backed protection even after your Yamaha Limited Warranty expires. A special note: If visiting your dealer isn’t convenient, contact Yamaha with your VIN number and we’ll be happy to help you get the YAMAHA EXTENDED SERVICE Y.E.S.

  • Page 130: Index

    Index Display, menu screen ......5-15 Drive chain, cleaning and lubricating..8-25 ABS warning light........5-5 Labels, location ........1-1 Drive chain slack ........8-24 Air filter element ........8-16 Luggage strap holders ......5-37 Auxiliary DC jack........5-37 Auxiliary system warning light....5-6 Engine break-in ........
  • Page 131 Vehicle identification number....11-1 Vehicle lights ........8-33 Warranty, extended ......11-10 Warranty, limited........11-8 Wheel bearings, checking ....8-30 Wheels..........8-20 Yamalube ..........8-13 YRC functions visual guide..... 4-5 YRC settings......... 5-16 YRC (Yamaha Ride Control) ....4-1 YVSL ............4-8 12-2...
  • Page 133 Yamalube – Take care of your Yamaha with legendary Yamalube oils, lubricants, and care products. They’re formulated and approved by the toughest judges we know: the Yamaha engineering teams that know your Yamaha from the inside out.
  • Page 134 PRINTED IN JAPAN 2021.12-0.1×1 ! (E)

This manual is also suitable for:

Mt10n 2021Mt10nc 2021

Table of Contents