ABB AutoLink Mounting Instructions
  1. Manuals
  2. Brands
  3. ABB Manuals
  4. Industrial Equipment
  5. AutoLink
  6. Mounting instructions
ABB AutoLink Mounting Instructions

ABB AutoLink Mounting Instructions

Hide thumbs Also See for AutoLink:
Table of Contents

Advertisement

Quick Links

Download this manual
TEHI95094– rev. 1
AutoLink
15kV, 27kV, 33kV
Mounting Instructions

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the AutoLink and is the answer not in the manual?

Questions and answers

Related Manuals for ABB AutoLink

Summary of Contents for ABB AutoLink

  • Page 1 TEHI95094– rev. 1 AutoLink 15kV, 27kV, 33kV Mounting Instructions...
  • Page 2 • Pay special attention to the danger notes indicated in the manual by the following symbol: Responsible behavior safeguards your own and other’s safety! For any requests, please contact the ABB Assistance Service. The information and illustrations are not binding. We reserve the right to make changes during technical development of the product.

  • Page 3: Table Of Contents

    6 Installation ........................5 6.1 General ........................5 6.2 Installation and service conditions................. 5 6.3 Initial Setting or Previous Setting Modification Instructions........6 6.4 AutoLink Repositioning..................8 7 Commissioning ......................10 7.1 General procedures ..................... 10 8 Maintenance ....................... 10...

  • Page 4: Introduction

    Also make sure that all materials described in the shipping note are included in the supply. Should any damage or irregularity be noted in the supply on unpacking, notify ABB (directly or through the agent or distributor) as soon as possible and in any case within five days of receipt.

  • Page 5: Storage

    The AutoLink Electronic Sectionalizer is a protective device that operates at a permanent failure in the distribution line. It must be used together with a backup recloser. Please take note that the AutoLink is not a fuse tripping device, therefore it cannot be used as a protective device by itself.

  • Page 6: Initial Setting Or Previous Setting Modification Instructions

    ANSI C37 63: Automatic Sectionalizer All accident prevention regulations in force in relative countries For special installation requirements or other operating conditions, please contact ABB. 6.3 Initial Setting or Previous Setting Modification Instructions Remove the contact cap (Fig. 1 A) with a 34mm fork spanner holding the base (Fig. 1 B) with the hand.
  • Page 7 7 / 11 Once the calibration current and counts are selected, cover the dipswitch with a generous amount of silicon grease (Fig. 3), supplied with AutoLink. Figure 3 Check the condition of the O’Ring (Fig. 2 E) and apply silicon grease (Fig. 4 F) both...

  • Page 8: Autolink Repositioning

    (torque between 8 and 10 Nm) without damaging the O’Ring (Fig. 5). Figure 5 6.4 AutoLink Repositioning Push the interlocking bolt (Fig. 6) until blocked (it will spin freely, but it will not reset). Do not strike the bolt, nor use any type of tool to reset.
  • Page 9 TEHI95094 – rev. 1 9 / 11 Figure 7 Turn the tensioning device support 90° , until it is firmly blocked (Fig. 8) Figure 8 Place the pole in the tube inferior eyelet (Fig. 9) and position in the isolating support body.

  • Page 10: Commissioning

    - Check that the mobile lever and the lower support of the AutoLink move easily at the joint. Clean and lubricate the joint surfaces of both pieces.
  • Page 11 TEHI95094 – rev. 1 11 / 11 ©Copyright 2007 ABB, All rights reserved Document Title AutoLink Document No. Date & Rev. Ind. No. of Pages Page TEHI95094-EN...

Table of Contents