Advertisement
INSTALLATION
1.Place the weather bar. The installation surface in the shower room must be flat.
1.放置挡水条，淋浴房安装面必须打水平。
1.Install the panel glasses and the magnetic seal jambs.
2.Adjust the distance between the edge of the glasses and the inter magnetic seal jambs to
680 mm.
3.Install the stainless steel weather bar assembly as shown in the figure below.
1.安装固定玻璃和磁条型材。
2.调节固玻边沿到夹磁条型材之间的距离为680mm(如下图)。
3.按下图所示装好不锈钢挡水条组件。
1.Loosen the lock screws on the inside of the hinge. Insert the adjusting mechanism into
the opening of the glasses (make sure that the plastic cover and the plastic washers on
both sides of the glasses are present before installation).Lock the hinges onto the panel
glasses.Tighten the upper and the lower adjust screws while keeping the hinge
horizontal. Then tighten the connecting screws on the internal cover.
1.松开铰链内侧锁板螺丝，将合页调节件卡入玻璃开口内（安装前需确保调节塑胶套无脱
落，玻璃两侧的塑胶垫片无遗漏。）将合页锁至固定玻璃上。当合页处于水平状态时拧
紧上下两个调节螺丝，最后锁紧内侧盖板的连接螺丝。
1380414-T01-A
IMPORTANT:
Tray MUST be level
along front edge.
0mm
重要：
底盘必须水平。
STEP
Installed weather bar
不锈钢挡水条安装方式
STEP
Adjusting mechanism
调节件
Reduce the distance between
the cover and the glass with
the adjusting mechanism.
可通过调节件减小盖板与玻璃
间的间隙。
Important:
The hinge externally marked with "UP/向上"
shall be installed on the top and that marked with
"DOWN/向下" on the bottom.
重要：
铰链外表面有"UP/向上"标识为上铰链；
铰链外表面有"DOWN/向下"标识为下铰链。
STEP
安装
1.Install the seal and wall clip onto the panel glasses. Place the glasses horizontally 30 mm
to the external edge of the stone base from the inside). Then draw lines and drill holes.
2.Place the magnetic seal jambs horizontally 30 mm to the external edge of the stone base
from the inside. Then draw lines and drill holes.
1.固玻上先装好胶条和墙夹，在石基外沿内偏30mm处水平放置，然后画线、钻孔。
2.磁条型材同样在石基外沿内偏30mm处水平放置，然后画线、钻孔。
重要：
墙夹要装正后，才开始画线、钻孔。
Important:
Draw lines and drill holes after installing the wall clip upright.
The wall jamb must be kept
vertical.
上墙材必须垂直。
1
1.Drill the installation holes into the wall according to the dimensions shown in the
figure below.
2.Install the handle.
1.按下图尺寸在墙面钻好安装孔。
2.安装拉杆。
Tighten all set screws
所有紧定螺钉需拧紧
3
1.Adjust the closing angle with the set screw.
1.通过紧定螺钉调整好关门的角度。
Tips:
1.The room must be sufficiently supported before the door
glass is installed.
2. Four set screws on the top hinge need to be loosened
when the door glass is being removed, otherwise the
hinge may rebound and cause the glass to break.
温馨提示：
1.门玻安装前，房体必须要有足够的支撑；
2.拆卸淋浴房门玻时，需松掉上铰链的四颗调节紧定螺钉，
防止铰链回弹引起玻璃爆裂。
The top hinge is used only to adjust
the closing angle
Taper ring
上铰链仅用于闭门角度的调节
锥形孔圈
Be careful of the orientation
of the taper ring
注意锥形孔圈方向
The bottom hinge is used to
adjust the closing speed
5
下铰链用于关门速度快慢的调节
-3-
STEP
Wall body
上墙座
90
Glass
玻璃
Position of the installation holes for
the wall body
上墙座钻孔位置示意图
*Note:
The decorative cover needs to be installed
after the trolley is installed
*注意：
拉杆安装完成后，需要扣上装饰盖
STEP
Top hinge
Outside
上铰链
房体外侧
!
Safety Tips:
External set screw
The internal and external set screws
外侧紧定螺钉
must be loosened when the door glass
is to be installed or removed. Otherwise,
the hinge may rebound and cause glass
Internal set screw
breakage.
内侧紧定螺钉
Inside
!
安全提示：
房体内侧
安装或拆卸门玻时，都须松掉内外紧定螺
钉，以防止铰链回弹，导致玻璃破碎。
Top hinge
Suggested closing angle <180°
上铰链
建议闭门角度<180°
Door glass
门玻
Outside
房体外侧
Inside
房体内侧
Adjustment Tips:
Loosen the external set screws, and tighten the internal set screws. Closing
angle ＜180°
Loosen the internal set screws, and tighten the external set screws. Closing
angle ＞180°
(Suggested offset distance: 30mm)
调节提示：
松外侧紧定螺钉 ， 紧内侧紧定螺钉时 ， 闭门角度＜180°;
松内侧紧定螺钉 ， 紧外侧紧定螺钉时 ， 闭门角度＞180°。
(闭门偏移距离建议为 30mm)
Bottom hinge
Adjustment Tips:
下铰链
Closing speed gets lower when
adjusting towards "-";
Closing speed gets higher when
adjusting towards "+";
调节提示：
向"-"调节时，关门速度变慢；
向"+"调节时，关门速度变快。
Bottom hinge
Door glass
!
Safety Tips: Positions of set screws for bottom
下铰链
门玻
hinge have been adjusted before delivery. If no
Inside 房体内侧
specified closing angle is needed, no more
adjustment is needed.
Outside 房体外侧
!
安全提示：下铰链紧定螺钉位置，出厂时已调节
好，如无特殊关门角度，无须调节。
α: Starting angle for closing acceleration
α为闭门加速启动角度
Tips for adjustment of starting angle for closing acceleration:
Loosen the external set screws, and tighten the internal set screws.
Starting angle <α
Loosen the internal set screws, and tighten the external set screws.
Starting angle >α
闭门加速启动角度调节提示：
松外侧紧定螺钉 ， 紧内侧紧定螺钉时 ， 启动角度<α;
松内侧紧定螺钉 ， 紧外侧紧定螺钉时 ， 启动角度>α。
STEP
2
4
6
Advertisement
