Download Print this page

Advertisement

Quick Links

2610041926 10-15 WC18CV_WC18C 10/7/15 9:07 AM Page 4
The manufacturer is not responsible for radio
interference caused by unauthorized
modifications to this equipment. Such
modifications could void the user's authority to
operate the equipment.
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following
two conditions:
1) This device may not cause harmful
interference, and
2) This device must accept any interference
received, including interference that may
cause undesired operation.
These limits are designed to provide
reasonable protection against harmful
interference in a residential installation. This
equipment generates uses and can radiate
radio frequency energy and, if not installed
and used in accordance with the instructions,
may cause harmful interference to radio
communications. However, there is no
guarantee that interference will not occur in a
When batteries are not in
tool or charger, keep them
WARNING
away from metal objects. For example, to
protect terminals from shorting DO NOT place
Do not attempt to disas-
semble the battery or
WARNING
remove any com ponent projecting from the
battery terminals. Fire or injury may result.
Prior to disposal, protect exposed terminals
with heavy insulating tape to prevent shorting.
Lithium-ion Batteries
If equipped with a lithium-ion battery, the
battery must be collected, recycled or disposed
of in an environ mentally sound manner.
"The EPA certified RBRC Battery
Recycling Seal on the lithium-ion
(Li-ion) battery indicates Robert
Bosch Tool Corporation is
voluntarily participating in an
FCC Caution:
particular installation. If this equipment does
cause harmful interference to radio or
television reception, which can be determined
by turning the equipment off and on, the user
is encouraged to try to correct the interference
by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the
equipment and receiver.
• Connect the equipment into an outlet on a
circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced
radio/TV technician for help.
Changes or modifications not expressly
approved by the party responsible for
compliance could void the user's authority to
operate the equipment.
Battery Care
batteries in a tool box or pocket with nails,
screws, keys, etc. Fire or injury may result.
DO NOT PUT BATTERIES INTO FIRE OR
EXPOSE TO HIGH HEAT. They may explode.
Battery Disposal
industry program to collect and recycle these
batteries at the end of their useful life, when
taken out of service in the United States or
Canada. The RBRC program provides a
convenient alterative to placing used Li-ion
batteries into the trash or the munici pal waste
stream, which may be illegal in your area.
Please call 1-800-8-BATTERY for information
on Li-ion battery recycling and disposal
bans/restrictions in your area, or return your
batteries to a Skil/Bosch/Dremel Service
Center for recycling. Robert Bosch Tool
Corporation's involvement in this program is
part of our commitment to preserving our
environment and conserving our natural
resources."
-4-

Advertisement

loading

Summary of Contents for Bosch WC18CV

  • Page 1 Skil/Bosch/Dremel Service “The EPA certified RBRC Battery Center for recycling. Robert Bosch Tool Recycling Seal on the lithium-ion Corporation’s involvement in this program is (Li-ion) battery indicates Robert...
  • Page 2 INDICATOR (GREEN) CHARGING PLATFORM 12 V PLUG POWER SUPPLY DRAW HOOK Charger WC18CV Approximate Charging time for 2Ah battery: Input voltage: 290V 45min - 80%, 55min - 100% Output: 18V Approximate Charging time for 4Ah battery: Power supply 1600A00AM7 (Designed for...
  • Page 3 2610041926 10-15 WC18CV_WC18C 10/7/15 9:07 AM Page 6 WC18H Holster Assembly The Bosch power supply and wireless Note: Refer to Fig. 2a. charger must be used in conjunction with 1. Remove Screw/Nut 1. the wireless charging holster WC18H. 2. Loosen the (2x) Screw 2.
  • Page 4 2610041926 10-15 WC18CV_WC18C 10/7/15 9:07 AM Page 7 NUT 1 FIG. 2a INSERT SCREW 1 HOLSTER TOOL BATTERY SCREW 2 BATTERY RAIL POWER BATTERY CORD GUIDE SLOT UPPER TRAY GUIDE SLOT CHARGER LOWER TRAY GUIDE SLOT TRAY BOLT 1 TRAY GUIDE RAIL BATTERY FIG.
  • Page 5: Installation

    2610041926 10-15 WC18CV_WC18C 10/7/15 9:07 AM Page 8 Installation The Bosch power supply and wireless charger must be used in conjunction with the wireless FIG.3 charging holster WC18H. The holster allows secure installation in the cargo areas of a HOLSTER vehicle, either fastened to a shelf or to a wall.
  • Page 6 2610041926 10-15 WC18CV_WC18C 10/7/15 9:07 AM Page 9 Holster Side Mounting Instructions 3. Remove Bolt 1 (Fig. 2a) from bottom side mounting hole. The holster may be mounted to shelf or workbench side walls through the side 4. Attach holster to wall as shown in Fig. 5 mounting holes using the hardware provided Fasten holster securely to (Fig.
  • Page 7 2610041926 10-15 WC18CV_WC18C 10/7/15 9:07 AM Page 10 Holster Side Mounting Orientation power tool to fall out of holster (Fig. 6b) . When side mounting the holster, use only the Do not mount the holster to a ceiling (Fig. orientations between 0° and 80° from 7a).
  • Page 8 2610041926 10-15 WC18CV_WC18C 10/7/15 9:07 AM Page 11 Bottom Mounting Instructions The holster may be mounted to flat surfaces FIG. 9 through the holes in its base (Fig 8). Do not mount holster upside down (Fig. 9). Fasten holster securely to horizontal surfaces with WARNING appropriate hardware.
  • Page 9 2610041926 10-15 WC18CV_WC18C 10/7/15 9:07 AM Page 12 Operating Instructions The battery is supplied partially charged. battery can be charged at any time, without Completely charge the battery before using your reducing its service life. Interrupting the charging cordless tool for the first time. The lithium ion procedure does not damage the battery.

This manual is also suitable for:

Wc18c