Maintenance; Register Online - DeWalt DWE625 Instruction Manual

Using a Side Fence (Fig. M)

CAUTION: Ensure working position is comfortable and
at a suitable working height.
1. Ensure the wing bolts
guide rods 26 into the routing base
the wing bolts.
2. Adjust the fence fine adjustment knob
required distance and clamp in place with the wing
bolts 28 .
3. Then lower the cutter height until the cutter is just above
the workpiece.
4. Fine adjustments are possible by loosening the
wing bolt 28 and adjusting the side fence fine
adjustment knob 29
5. Tighten the wing bolt
nOTE: One revolution of the side fence fine adjustment
knob 29 equals 3/64" (1.0 mm) of side feed.
6. Lower the cutter onto the workpiece and set the cutter
height by to the required distance. Refer to Setting the
Router Depth.
7. Switch the router on and after the cutter reaches full
speed, gently lower the cutter into the workpiece and
lock the plunge.
8. Feed along the workpiece, keeping sideways pressure to
ensure the side fence does not wander away from the
workpiece edge and downward pressure on the inside
hand to prevent the router from tipping.
9. When finished, raise the router, secure with the plunge
locking lever 6 and switch the router off.
nOTE: When starting the cut, keep the pressure on the front
cheek until the back cheek contacts the workpiece edge.
nOTE: At the end of the cut, keep pressure on the back
cheek until the cut is finished. This will prevent the router
cutter swinging in at the end of the workpiece and
nipping the corner.
Side Fence Routing (Fig. I, J)
The side fence is used to guide the router when moulding,
edge profiling or rebating the edge of a workpiece or when
routing grooves and slots in the center of the workpiece,
parallel to the edge.
The edge of the workpiece must be straight and true.
The strips 31 are adjustable and should be set ideally with a
1/8" (3 mm) gap each side of the cutter.

MAINTENANCE


WARNING: To reduce the risk of serious personal
injury, turn unit off and disconnect it from
power source before making any adjustments or
removing/installing attachments or accessories.
An accidental start‑up can cause injury.
Your D WALT power tool has been designed to operate
e
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
28 are fully released. Slide the
10 and tighten
29 to the
.
28 to secure the position.
Cleaning

WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the
risk of eye injury, always wear ANSI Z87.1 approved
eye protection and an approved dust mask when
performing this procedure.

WARNING: Never use solvents or other harsh
chemicals for cleaning the non‑metallic parts of the
tool. These chemicals may weaken the plastic materials
used in these parts. Use a cloth dampened only with
water and mild soap. Never let any liquid get inside the
tool; never immerse any part of the tool into a liquid.
Accessories

WARNING: Since accessories, other than those offered
by D WALT, have not been tested with this product, use
e
of such accessories with this tool could be hazardous.
To reduce the risk of injury, only D
accessories should be used with this product.
Recommended accessories for use with your tool are
available at extra cost from your local dealer or authorized
service center. If you need assistance in locating any
accessory, please contact D
(1‑800‑433‑9258) or visit our website:www.dewalt.com.
Base Mounting Points for Accessories (Fig. N)
This router has three threaded holes
that allows it to attach to other accessories.
Repairs

WARNING: To assure product SAFETY and RELIABILITY,
repairs, maintenance and adjustment (including power
cord repairs, and brush inspection and replacement,
when applicable) should be performed by a D
factory service center or a D
center. Always use identical replacement parts.

Register Online

Thank you for your purchase. Register your product now for:
• WARRAnTY sERViCE: Registering your product will
help you obtain more efficient warranty service in case
there is a problem with your product.
• COnFiRMATiOn OF OWnERshiP: In case of an
insurance loss, such as fire, flood or theft, your registration
of ownership will serve as your proof of purchase.
• FOR YOUR sAFETY: Registering your product will
allow us to contact you in the unlikely event a safety
notification is required under the Federal Consumer
Safety Act.
• Register online at www.dewalt.com
English
WALT recommended
e
WALT call 1‑800‑4‑D WALT
e e
38 built into the base
e
WALT authorized service
e
WALT
11