Table of Contents
Advertisement
Quick Links
Instructions
AirMax Gas Air Compressor
IMPORTANT SAFETY INSTRUCTIONS
Read all warnings and instructions in this manual.
SAVE THESE INSTRUCTIONS.
-For Compressed Air Delivery-
-For outdoor use only-
Model
Horse Power and
Motor Brand
1310G
200cc Honda
1720G
270cc Honda
proven quality. leading technology.
http://gracomanual.com
Maximum Working
Pressure
PSI
MPa
bar
125
0.86
8.6
175
1.21
12.1
3A0595D
EN
37-1106 041811
Advertisement
Table of Contents
Related Manuals for Graco AirMax 1310G
Summary of Contents for Graco AirMax 1310G
- Page 1 Instructions AirMax Gas Air Compressor 3A0595D -For Compressed Air Delivery- -For outdoor use only- IMPORTANT SAFETY INSTRUCTIONS Read all warnings and instructions in this manual. SAVE THESE INSTRUCTIONS. Model Horse Power and Maximum Working Motor Brand Pressure 1310G 200cc Honda 0.86 1720G 270cc Honda...
-
Page 2: Table Of Contents
Personal Protective Equipment ........5 Notes ................24 Component Identification ..........6 Technical Data ............. 25 Installation & Preparation Graco Standard Warranty ........... 26 Instructions ..............9 Initial Setup ..............9 Gasoline Engine ............10 Pre-Start Checklist ............10 Operation Instructions ..........11 Start-Up ................. -
Page 3: Important
The following warnings are for the setup, use, maintenance, and repair of this equipment. The exclama- tion point symbol alerts you to a general warning and the hazard symbols refer to procedure-specific risks. When these symbols appear in the body of this manual, refer back to these Warnings. Product-specific hazard symbols and warnings not covered in this section may appear throughout the body of this manual where applicable. -
Page 4: Toxic Fumes Hazard
WARNING before refueling. • Do not refuel indoors or in a poorly ventilated area. • Always refuel slowly to avoid the possibility of spilled fuel which may cause a risk of fire. • Do not operate the unit if gasoline is spilled. Wipe unit clean and move the unit away from the spill. Avoid creating any ignition until the gasoline has evaporated. -
Page 5: Moving Parts Hazard
WARNING MOvING PARTS HAZARD Risk of bodily injury from moving parts. • Before performing maintenance always turn off air compressor. Bleed pressure from the air hose and disconnect spark plug wire to prevent engine from starting unexpectedly. All repairs to the air compres- sor should be made by an Authorized Service Person. -
Page 6: Component Identification
Component Identification 262361 - Model 1720G Item Description Item Description 1 Beltguard 9 Engine 2 Air Filter 10 Engine Throttle Control 3 Oil Fill Port 11 Pressure Gauge - Tank Psi 4 Air Compressor Pump 12 Tank Drain Valve 5 Pump Oil Drain 13 Pressure Relief Valve 6 Oil Sight Glass 14 Pressure Gauge - Outlet Psi 7 Pilot Valve 15 Outlet Fitting 8 Engine Switch 16 Pressure Regulator... -
Page 7: Beltguard
Component Identification 262360 - Model 1310G Item Description Item Description 1 Engine 9 Beltguard 2 Engine Switch 10 Air Filter 3 Engine Air Throttle Control 11 Oil Fill Port 4 Pilot Valve 12 Pump 5 Oil Sight Glass 13 Pressure Regulator 6 Pump Oil Drain 14 Outlet Fitting 7 Pressure Relief Valve 15 Pressure Gauge - Outlet Psi 8 Pressure Gauge - Tank Psi 16 Tank Drain Valve... -
Page 8: Air Compressor Pump
Component Identification AIR COMPRESSOR PUMP (Single Stage): To compress air, the pistons move up and down in the cylinders. On the downstroke, air is drawn in through the air intake SAFETY RELIEF VALVE: This valve is designed to pre- valves while the exhaust valves remain closed. On the vent system failures by relieving pressure from the sys- upstroke, air is compressed, the intake valves close tem when the compressed air reaches a predetermined... -
Page 9: Installation & Preparation Instructions
INSTALLATION & PREPARATION INSTRUCTIONS Do not place air compressor in an area: Initial Setup • Where there is evidence of oil or gas leaks. • Where flammable gas vapors or materials may be present. • Where air temperatures fall below 32°F or exceed Read safety warnings before setting-up air compres- 104°F. -
Page 10: Gasoline Engine
INSTALLATION & PREPARATION Pre-Start Checklist INSTRUCTIONS 1. Check oil level. Add if necessary. 2. Remove any moisture in the air compressor air tank. Gasoline Engine Risk of bodily injury. Never attempt to open the Air Tank Review “Fire & Explosion Precautions” pg. 3, before Drain Valve when more than 10 PSI of air pressure is in fueling. -
Page 11: Operation Instructions
OPERATION INSTRUCTIONS Shutdown 1. To stop the air compressor, move the engine switch to Start-Up the “OFF” position. Refer to the Engine Manual. 2. Drain air from the air tanks by releasing air with an attached air tool or by pulling on the safety relief valve. -
Page 12: Maintenance Instructions
MAINTENANCE INSTRUCTIONS NOTICE * The pump oil must be changed after the first Read the instruction manual before performing main- 50 hours of operation and every 200 hours or 3 tenance. The following procedures must be performed months, whichever comes first. when stopping the air compressor for maintenance or service. -
Page 13: Troubleshooting
Torque head bolts: Single Stage=17 ft./lbs. Two Stage=33 ft./lbs. Air blowing from Air Intake Filter. Defective inlet (reed) valve. Contact Graco Customer Service. Moisture in discharge air. Condensation in air tank caused by Run air compressor a minimum of high level of atmospheric humidity... - Page 14 Oil leaks. Torque head bolts: Single Stage=17 ft./lbs. Two Stage=33 ft./lbs. Worn piston rings or scored cylinder. Contact Graco Customer Service. Oil has milky appearance. Water in oil due to condensation. Change oil and move air compres- sor to a less humid environment.
-
Page 15: Notes
Notes... -
Page 16: Air Compressor - Parts
Air Compressor - Parts 262360- Model 1310G... - Page 17 Washer 110755 Beltguard Cover 16E768 Locknut - 1/4-20 102040 44 pDecal - Operating Instructions (E) Decal - Graco Airmax 1310G 16E424 Bolt 16E599 9 pDecal - Maintenance 46 pDecal - Operating Instructions (S/F) Instructions (E) 47 pDecal - Risk of Burns...
-
Page 18: Pump Assembly - Parts
Pump Assembly - Parts 16E739 (for use with Model 1310G) - Page 19 Pump Assembly - Parts 16E739 (for use with Model 1310G) DESCRIPTION PART # Kit, Repair, Valve Plate Assy 24E998 Includes 2-8 (1) Kit, Repair, Piston Seals 24E999 Includes 15 Kit, Repair, Piston 24F002 Includes 11-14 Kit, Repair, Pump Gaskets 24F001 Includes 2, 8, 9, 10...
-
Page 20: Air Compressor - Parts
Air Compressor - Parts 262361- Model 1720G... - Page 21 38p Decal - Warning, Beltguard Instructions (E) In Place 4p Decal - Maintenance Beltguard Back 16E765 Instructions (S/F) 40p Decal - Warning: Risk of Burns Decal - Graco Airmax 1720G 16E425 Bolt 16E735 Locknut - 1/4-20 102040 Beltguard Bracket 16E685...
-
Page 22: Pump Assembly - Parts
Pump Assembly - Parts 16E738 (for use with Model 1720G) - Page 23 Pump Assembly - Parts 16E738 (for use with Model 1720G) DESCRIPTION PART # KIT, REPAIR, VALVE PLATE ASSY 24F003 INCLUDE 2-9 (1) KIT, REPAIR, PISTON SEALS 24F004 INCLUDES 16, 17 KIT, REPAIR, PISTON 24F006 INCLUDES 12-15, 18-21 KIT, REPAIR, PUMP GASKETS 24F005 INCLUDES 2, 7, 9, 10, 11...
-
Page 24: Notes
Notes... -
Page 25: Technical Data
Technical Data MODEL NUMBER 262360 262361 Engine: Honda Size 200cc 270cc Engine Type 4 Stroke, Overhead Valve, Single Cylinder Oil Type SAE 10W 30 Oil Capacity (oz./liters) 20 oz./591 ml 37 oz. /1094 ml Fuel Type Unleaded Gasoline 86 Octane Minimum Fuel Capacity (gallon/liters) .95/3.6 1.6/6.05... -
Page 26: Graco Standard Warranty
Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written...